- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: No Display on BL460c G6
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2010 01:21 AM
тАО03-22-2010 01:21 AM
No Display on BL460c G6
One of the blades isn't showing any display anymore.
Accessing through ILO gives a blank screen, accessing through the SUV-dongle at the front of the server directly also shows the same blank screen.
I've tried booting with minimum config and also switching into maintenance mode (moving maintenance switch #1, #5 and #6 in ON position) without any success.
Also noticed that during the time the server is on, the fans on the enclosure for that area turn at full RPM.
is that a dead board issue? or any other explanations?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2010 01:26 AM
тАО03-22-2010 01:26 AM
Re: No Display on BL460c G6
did you tried to run the failed blade in another blade BAY/SLOT ???
mikap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2010 01:57 AM
тАО03-22-2010 01:57 AM
Re: No Display on BL460c G6
yea I've tried that also. running it in another enclosure bay, same thing.
no display
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2010 03:06 AM
тАО03-22-2010 03:06 AM
Re: No Display on BL460c G6
so would recommend to open HW call in HP for your blade server.
mikap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2010 07:53 AM
тАО03-22-2010 07:53 AM
Re: No Display on BL460c G6
Is there a red or amber LED on the front of the blade when you power it on? Can you check the IML (Integrated Management Log) for this server?
It sounds like either a failed system board or a failed processor, but there are other potential causes. Visit the Onboard Administrator, select your blade, then click the IML Log tab. If this doesn't provide answers then you will need to call HP support.
good luck!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2010 11:29 AM
тАО03-24-2010 11:29 AM
Re: No Display on BL460c G6
thanks all for your contribution.
WFH-WI - no red light on the blade, didn't get much info from the IML log either.
I changed the system board earlier - server is up and running fine now.