- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- P-Class Power questions .... PLEASE HELP!!!!
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-10-2012 02:34 AM
02-10-2012 02:34 AM
P-Class Power questions .... PLEASE HELP!!!!
I have a configuration of 2 x 3 phase power attached to 4 enhanced enclosures. A couple of days ago we had the left side of the rack power down. When we noticed and looked at the rack, all the PSU's looked on, the scalable bus bars and power enclosures all lights were on, but all the blades had no lights, not even a standby light. Reseating the blades did make them come back up. But I'm trying to find out why it happened. How do you check on P-Class what the redundancy is set to on? I have attached a serial connection and collected the below. Any advise would be greatly appreciated. If it helps we have a mixture of BL25p and BL45p in the rack. we are alo running 2.4 f/w on all enclosures.
LQQQQQQQ REDUNDANCY KEY QQQQQQQQQQK
XXXXX = NOT PS REDUNDANT X
XXXXX = NOT BUS BAR REDUNDANT X
XXXXX = NOT PWR. ENCL. REDUNDANT X
MQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQJ
ICMB A BOTH B
E410 1174 240 0 Z-CLASS CHASSIS <<<<<<< DO WE KNOW WHY B IS SET 0
E22F 908 240 454 Z-CLASS CHASSIS
992F 681 240 908 Z-CLASS CHASSIS
CCF0 681 240 908 Z-CLASS CHASSIS
4CBB >8721< >8721< POWER CHASSIS
3B24 >8721< >8721< POWER CHASSIS
Many Thanks
Koopa79
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-16-2012 08:51 AM
02-16-2012 08:51 AM
Re: P-Class Power questions .... PLEASE HELP!!!!
question: Are all power zones set the same?
Louis
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-20-2012 03:36 AM
02-20-2012 03:36 AM
Re: P-Class Power questions .... PLEASE HELP!!!!
I believe that on 2.4 f/w everything gets set to zone 3, which is obviously something you can't normally set by the back of the enclosures.