- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: how to configure LACP in 6125xlg Blade switch
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-10-2016 07:07 AM
01-10-2016 07:07 AM
how to configure LACP in 6125xlg Blade switch
hi
plaese someone explain how can I config 6125xlg switch to provide LACP(and what is the number of ports that can use in LACP) configuration ??!!
and how can I config a backup port in LACP which comes in LACP when one port (that's work in LACP) status goes down??
thanks alot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-10-2016 10:10 PM - edited 01-10-2016 10:11 PM
01-10-2016 10:10 PM - edited 01-10-2016 10:11 PM
Re: how to configure LACP in 6125xlg Blade switch
create the aggregated link interface:
interface bridge-aggregation 1
Add physical interfaces to the aggregation group:
int g1/0/1 port link-aggregation group 1
int g1/0/2 port link-aggregation group 1
I am guessing you can have 8 active ports in an aggregated group.
If you want a port to be a member of an aggregation group without being up, you could set it with a link-aggregation port-priority with a higher value than the default of 32K, so that if there are more ports configured in the aggregate group than the allowable maximum, it will stay down until another of the ports goes down.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2016 05:55 AM
01-11-2016 05:55 AM
Re: how to configure LACP in 6125xlg Blade switch
thanks for reply but I Read in Switch document that says By default, the maximum number of Selected ports for an aggregation group is 32. my questions is that means we can have 32 port in LACP ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2016 08:27 AM
01-11-2016 08:27 AM
Re: how to configure LACP in 6125xlg Blade switch
I haven’t tested, but my understanding is that yes, if you IRF enough 6125s so that you actually have 32 ports to add to LACP, and if the device you are connecting them to also actually supports 32 ports in selected state in LACP, then you could have 32 selected ports in a single LACP group. OP also asked about backup ports...... As example, you could add 4 ports to a LACP group, and then modify the maximum # of allowable selected ports ('link-aggregation selected-port maximum number') to 3. Then one of those ports will be in unselected state ready to switch over to selected in case any of the 3 selected ports go down. You can also control which port is the backup port by using port priorities ('link-aggregation port-priority port-priority').
The Layer 2 LAN Switching Configuration Guide is great resource for this topic.
Hope that helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-13-2016 01:21 AM
01-13-2016 01:21 AM
Re: how to configure LACP in 6125xlg Blade switch
Thank you I will try your answer and reply result.
thank's alot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-14-2016 11:14 PM
01-14-2016 11:14 PM
Re: how to configure LACP in 6125xlg Blade switch
we have to lacp group with 8 port on each lacp and two 10G external port (ex port 14 and port 15) come with access link (no vlan)
we want port 14 send traffic to lacp group 1 and port 15 send to lacp group 2
how can assain external port to send traffic on which lacp group ?
thanks for answers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-15-2016 12:04 PM
01-15-2016 12:04 PM
Re: how to configure LACP in 6125xlg Blade switch
You can make port 14 and LACP group 1 access ports (or trunk if you need packets tagged) in VLAN X.
Then port 15 and LACP group 2 will be access ports in VLAN Y.
port link-type access
port access vlan x