Problem with EMU module on disk enclosure (EVA8000)

[Tsirulev Dmitry]

Hello all,
I have problem with disk enclosure EVA8000,
one of the four enclosures is not working properly. EMU alphanumeric display shows "00", then pause 20 seconds and shows "2.1" and beeps (one long beep and 5 short beep).
LEDs on the EMU show the normal (flashing-green -- green -- off). All cables work.
What is it?!!
Thanks in advance.

[Torsten.]

What does commandview say?

[Tsirulev Dmitry]

Torsten, enclosure are not visible, but disks from this enclosure placed in to unmappable hardware and work normally.
event log does not show errors.

[warrenfu]

In a host you can see the disk on the EVA8000? read or write is working properly?


Affirm EAB Cable connect first.

[Tsirulev Dmitry]

>"In a host you can see the disk on the EVA8000? read or write is working properly?"
Yes, they work.
EAB cable and all others cables is working, I checked them on other enclosure.
---
I understand that "00" it is problem EMU connections, bat I don't understand that such "2.1".

[Torsten.]

I would start with re-seating the EMU module.

[Tsirulev Dmitry]

Thanks Torsten, I already thought of it.

[Mark...]

Hi,
You should get the fault code from the emu to help. It is a SIX digit code. 2.1 is not enough.
To do this make sure the EMU readout says "Er" if not press and release the BOTTOM button till it does.
When you have Er press and HOLD the TOP button till you get a two digit number. Something like 0.4. for example. The . are important. Make a note of this code. Now press and release the TOP button and you will get the next two digits maybe 12. Now do the same again for the third pair of digits 00.
You should now end up with a six digit code for example 0.2. 01. 00
Post this and it can be decoded for you or look in the user guide if you have one.
Mark...

[Mark...]

Hi,
Oh yes Unmappable h/w is normally an EAB/CAN related problem so check EMU, EAB EMU cable, Termination of EAB - both ends - segmnets are all plugged to gether properly. If you do find a problem it can take a lonnng time for this event to go away in CV once fixed so check the above and then leave at least 30mins to see if resolved.
Mark...

[Tsirulev Dmitry]

Mark, thanks are final, but I will repeat:
"LEDs on the EMU show the normal (flashing-green -- green -- off). All cables work."
---
"EAB cable and all others cables is working, I checked them on other enclosure."
---
And alphanumeric display don't show "Er".
Only "00" and "2.1".

[Mark...]

Hi,
Read my note again above - it explains how to get the code out.
Mark...

[Tsirulev Dmitry]

>"When you have Er press and HOLD the..."
I speak - I DON'T have "Er" ))

[Torsten.]

...
To do this make sure the EMU readout says "Er" if not press and release the BOTTOM button till it does...

The "Er" entry is always there.

[warrenfu]

pls see the attachment 1

[warrenfu]

pls see the attachment 2

[warrenfu]

SORRY

Download the photo(i take the photo on my book 10Mb), input get Code No:e6574cb8 for download.

http://62.dc.ftn.qq.com/ftn_handler/8876ba68c2a5991aa98d8a912d41d6362fc201d9a149e41d768e7cf277b63d1562e6233aacae199377281357da10d8d3e3fd22e6985560d7e17f0ae82cd4ab61/M5314X.rar?k=5b36353799213dc788d8ab3712635017500500055105015c48030703054e560c0306180f06010315525451025150545e5c030c0234696275500504036c4d10591736


Hope this is can help you.

[Tsirulev Dmitry]

thanks all, but I know it ))) I read the manuals.
But I DON'T have "Er".
Only: "00"--20sec->"2.1" --20sec->"00"...etc.
I will replac this EMU module in to other enclosure tomorrow.
It will be problematic - I live in Russia, EVA is located in Tajikistan ))

[warrenfu]

Oh,so far away.

If in the Beijing of China, May be can help you. :)