- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE 3PAR StoreServ Storage
- >
- Re: Reconfigure StoreServ and SP network settings
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-09-2016 09:12 AM
08-09-2016 09:12 AM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-13-2016 01:21 PM - edited 08-13-2016 01:22 PM
08-13-2016 01:21 PM - edited 08-13-2016 01:22 PM
Re: Reconfigure StoreServ and SP network settings
What version of SP and StoreServ software?
The CLI command setnet is what you can use for the array.
Are you just talking about the network for management? Or do you have iSCSI and RCIP?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-15-2016 11:34 AM
08-15-2016 11:34 AM
Re: Reconfigure StoreServ and SP network settings
- The version of VSP is 4.1.0 and the console managemen is 4.7.1
- I am just talking about the network for management.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2016 06:53 PM
08-20-2016 06:53 PM
SolutionI've done the Re-IP of SP and 3PAR Management console before.
You can change service processor IP in the SPOCC. On the left side menu select SPmaint. Then Select "option 2. Network configuration. Then "Select Option 4. Change public IP Network interface parameters". Change the IP needed then "save and activate."
You will need to close the browser and re-open to enter new SP IP.
For 3PAR Management console. I used CLi command to change the Management IP. I refer to this link for guide:
http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0115900
Type setnet startaddr "current IP" "new IP" "subnet mask" and enter
It will show the status change of IP successfully started
Type shownet to view the status of changing IP.
To complete the setting type setnet finish. If you want to force IP change without verifying type setnet finish -f
Then type shownet again to verify the state.