- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: enable remote console on rp7410
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 08:09 AM
тАО10-15-2003 08:09 AM
Hi guys,
I'v got an rp7410 and i need to enable the remote console inorder to enable people to connect via modem. When I go to the MP and do er it dose not enable the remote console and the remote led dose not go on.
What is the sequanse of commands on the MP to enable it? if posible how to do it also on the rp 5470
Regards,
Mike
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 08:32 AM
тАО10-15-2003 08:32 AM
Re: enable remote console on rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 08:57 AM
тАО10-15-2003 08:57 AM
Re: enable remote console on rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 09:02 AM
тАО10-15-2003 09:02 AM
Re: enable remote console on rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 09:07 AM
тАО10-15-2003 09:07 AM
Re: enable remote console on rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 06:17 PM
тАО10-15-2003 06:17 PM
Re: enable remote console on rp7410
Guys ..
This is kind of urgent i'm at the SP>CM prompt but what option to use inorder to enable it.
thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2003 08:09 PM
тАО10-15-2003 08:09 PM
Re: enable remote console on rp7410
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-16-2003 03:35 AM
тАО10-16-2003 03:35 AM
Re: enable remote console on rp7410
It will then ask if you want to modify the configuration. you must specify 'y' for yes.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2003 01:58 AM
тАО10-19-2003 01:58 AM
SolutionFirst of all, in order to access the Management Processor for the initial installation, the M cable must first
be connected to the DB25 connector located on the Primary MP/SCSI board. The Primary
MP/SCSI board is located in the lower MP/SCSI board slot.
1. Connect the server to AC power.
2. Check the bulk power supply LED for each BPS.
3. Login to the MP:
3.1. Enter Admin at the login prompt. This term is case sensitive.
3.2 Enter Admin at the password prompt. This term is case sensitive.
Then,
1. At the MP Main Menu prompt (MP>), enter cm. From the MP Command Menu prompt (MP:CM>), enter
lc (for LAN configuration).
2. At the prompt, Do you want to modify the configuration for the customer LAN?, enter y.
The current IP address is shown; then the following prompt appears: Do you want to modify it? (Y/[N])
3. Enter y.
4. Enter the new IP address.
The customer shall provide this address for network interface 0.
5. Confirm the new address.
6. Enter the MP Network name.
This is the host name for the customer LAN. The name can be as many as 64 characters, and include
alpha numerics, - (dash), _ (under bar),. (period), or a space. It is recommended that the name be a
derivative of the complex name. For example, Acme.com_MP.
7. Enter the LAN parameters for Subnet mask and Gateway address.
This information shall come from the customer.
8. Once step 7 is completed, the system will indicate the parameters have been updated and return to the
MP Command Menu prompt (MP:CM>)
9. To check the LAN parameters and status, enter the ls command at the MP Command Menu prompt
(MP:CM>).
Please, ATTENTION:
Remote SP via GPM On Green Dial-in (remote) console enabled
Off Dial-in (remote) console is disabled, or SP not
installed, or SP installed and not active
If there is a cell board, please verify the following procedure.
Bye