- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: rp7420 deinstall, remove from rails
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2006 09:30 AM
тАО12-11-2006 09:30 AM
We are deinstalling a rp7420 and I cannot figure out how to slide it off the rails.
I was expecting a lock button other either side but there is none.
Before I start taking screws out does someone know the trick ?
Thanks in advance.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2006 10:35 AM
тАО12-11-2006 10:35 AM
SolutionBill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2006 01:42 PM
тАО12-11-2006 01:42 PM
Re: rp7420 deinstall, remove from rails
1. Fully extend the server.
2. There are 4 screw that lock the server onto the rail, you must open these.
3. You should be able to slide the server off the rails, as Bill said, it is very heavy so be careful.
Regards,
Sandy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2006 05:36 AM
тАО12-12-2006 05:36 AM
Re: rp7420 deinstall, remove from rails
if you extend the server out of the rack, you should find 2 handles inside the rack. To install them, you need to remove the servers side panels.
Remove the 4 (or6?) screws holding the server on the rails.
Be very very careful, the rails may spread and the server may fall down onto your feed.
So you need to secure the server while removing the screws.
Do this on your own risk only.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2006 08:31 AM
тАО12-12-2006 08:31 AM
Re: rp7420 deinstall, remove from rails
As Bill mentioned, I have seen so many different rail types over the years as well you never know if there is a trick or not.
Much thanks !