- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: rp8400
HPE 9000 and HPE e3000 Servers
1755382
Members
3765
Online
54828
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2007 02:42 AM
тАО11-01-2007 02:42 AM
Hi,
I have an rp8400 with 3 cell boards install and I only have 1 partiton.I need to add a fourth cell board.Is there away I can add this cell board to the partiton going thru the mp console or do I have to use partiton manager thru the os to add this cell board?
Thank you
Jon
I have an rp8400 with 3 cell boards install and I only have 1 partiton.I need to add a fourth cell board.Is there away I can add this cell board to the partiton going thru the mp console or do I have to use partiton manager thru the os to add this cell board?
Thank you
Jon
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2007 04:01 AM
тАО11-01-2007 04:01 AM
Solution
Hi Jon,
I would use the nPartition manager or the system managemnt homepage.
See
http://docs.hp.com/en/5991-1247B/index.html
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
I would use the nPartition manager or the system managemnt homepage.
See
http://docs.hp.com/en/5991-1247B/index.html
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2007 06:08 AM
тАО11-01-2007 06:08 AM
Re: rp8400
Hi Jon,
The easiest way is from command line:
example:
To add a new cell in slot3 to the existing partition with Partition Number 1.
#parmodify -p 1 -a 3:base:y:ri
#shutdown -Ry 0
(note upper case R for "reset for reconfiguraton)
the machine will reboot and stop at BIB.
Check the F/W is the same as the rest of the cells:
CTRL B
MP> CM> SYSREV
If ok, then release from BIB by doing:
MP> CM> BO
The machine will boot with all 4 cells in the npar.
Just make sure your new cell has the same speed CPU's and that the firmware is the same.
Cheers,
Phil
The easiest way is from command line:
example:
To add a new cell in slot3 to the existing partition with Partition Number 1.
#parmodify -p 1 -a 3:base:y:ri
#shutdown -Ry 0
(note upper case R for "reset for reconfiguraton)
the machine will reboot and stop at BIB.
Check the F/W is the same as the rest of the cells:
CTRL B
MP> CM> SYSREV
If ok, then release from BIB by doing:
MP> CM> BO
The machine will boot with all 4 cells in the npar.
Just make sure your new cell has the same speed CPU's and that the firmware is the same.
Cheers,
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2007 06:24 AM
тАО11-01-2007 06:24 AM
Re: rp8400
Thank you for your help.I thought you needed to do it from the os and not from the mp .
Jon
Jon
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP