- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- HPE Aruba Networking & ProVision-based
- >
- 5406zl port with Giants issue
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2014 03:15 AM
тАО02-18-2014 03:15 AM
5406zl port with Giants issue
I have several Cisco 3702i access points connected to an J8705A Gig-T/SFP zl module on HP5406zl.
Everyone of the 3702i shows up with RX error, more specific; giants error.
I'm running version; K.15.10.0009
The config on the switch is default. I allso have an 2510-10 that shows the same error.
In this switch I run version; Q.11.57
Show int on HP 5406
Name :
MAC Address : 001871-xxxxxx
Link Status : Up
Totals (Since boot or last clear) :
Bytes Rx : 4,224,972,101 Bytes Tx : 2,398,026,875
Unicast Rx : 10,245,508 Unicast Tx : 4,133,885
Bcast/Mcast Rx : 401,628 Bcast/Mcast Tx : 47,356,349
Errors (Since boot or last clear) :
FCS Rx : 0 Drops Tx : 0
Alignment Rx : 0 Collisions Tx : 0
Runts Rx : 0 Late Colln Tx : 0
Giants Rx : 19,292 Excessive Colln : 0
Total Rx Errors : 19,292 Deferred Tx : 0
Others (Since boot or last clear) :
Discard Rx : 0 Out Queue Len : 0
Unknown Protos : 0
Rates (5 minute weighted average) :
Total Rx (bps) : 5,172,968 Total Tx (bps) : 5,264,208
Unicast Rx (Pkts/sec) : 49 Unicast Tx (Pkts/sec) : 14
B/Mcast Rx (Pkts/sec) : 1 B/Mcast Tx (Pkts/sec) : 198
Utilization Rx : 00.51 % Utilization Tx : 00.52 %
Anyone suggestions on what to do if there is anything I can do on the switch?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2014 10:57 AM
тАО02-18-2014 10:57 AM
Re: 5406zl port with Giants issue
They are likely just jumbo frames, which would be disabled by default on Procurve.
vlan <number> jumbo (n config mode) enables them for a particular VLAN.
Or you could try to disable them at the other end or just forget about them. The chances that it's a faulty NIC are fairly small.
If you really want to get to the bottom of it, you'll probably need to capture the frames on something that supports jumo frames, see where they are coming from.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2017 06:03 AM
тАО08-31-2017 06:03 AM
Re: 5406zl port with Giants issue
I'm also having this issues. My HP 5406 is showing Giants Rx : 1,070 and continues to increment.
Basically my HP 5406 connects to Cisco 2951.
cisco has default configurations MTU (1500).
Could somone please help on this?