- Community Home
- >
- Software
- >
- HPE OneView
- >
- Unable to see Additional Mezzanine OneView enclosu...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-15-2016 11:21 PM
05-15-2016 11:21 PM
Unable to see Additional Mezzanine OneView enclosure with 4 x HP VC FlexFabric 10Gb/24-Port Module
Hi,
C7000 enclosure with 4 x HP VC FlexFabric 10Gb/24-Port Module managed by Oneview.
Scenario:
BL460c Gen9 with addtional 650M (installed on Mez slot 1) while creating server profile i am unable to see added Mezzanine card on port list. I should see 16ports (8 from 650FLB and 8650M additional Mez). Screen Shot attached.
Firmware Details Below:
Details Below
Server Model : BL460c Gen9
SPP FW Level : April-2016-SPP
Additional MezCard : 650M
VC Firmware : 4.41
OA Firmware : 4.40 Dec 08 2014
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-16-2016 08:12 PM
05-16-2016 08:12 PM
Re: Unable to see Additional Mezzanine OneView enclosure with 4 x HP VC FlexFabric 10Gb/24-Port Modu
Are you trying to design a Server Profile for a sepcific server resource, or a Server Hardware Type? If your trying to design one for a specific server resource, can you check to make sure that OneView has discovered the correct number of adapters? If Server Hardware Type, make sure it is the correct one that contains the 650m in your mezzanine slot.
If those all check out correct, then you need to look at the Logical Interconnect of the Enclosure where you are designing the Server Profile. Check to make sure it is operational.
Can you tell me what HPE OneView version you are using?
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2016 12:59 AM
05-18-2016 12:59 AM
Re: Unable to see Additional Mezzanine OneView enclosure with 4 x HP VC FlexFabric 10Gb/24-Port Modu
Hi,
Thanks for the reply. For you information, I have deployed test server BL460c Gen8 with additional 554M in the same OneView appliance and it works fine all the NIC's have been detected (see attached image). I am only facing issue on BL460c Gen9 with additional 650M that i am not able to see additional mezzanine ports while creating server profile. I have attached image for BL460c gen8 and gen9 for your ref.
OneView verion: 2.00.02-0219211