- Community Home
- >
- Servers and Operating Systems
- >
- HPE Synergy
- >
- HPE Synergy
- >
- Re: Command Line Interface for HPE Virtual Connect...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-12-2019 09:55 AM
03-12-2019 09:55 AM
Hallo,
does the SE 40Gb F8 module offer a Command Line Interface?
I am a little unsure:
On the one hand, there is a topic in this forum 'Monitoring Synergy Chassis' which I was reading that the Command Line Interface is only available for HPE support.
Additionally, the QuickSpecs document
'HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy'
does not include a reference to 'Command Line Interface' or 'CLI'.
On the other hand, there is a 'HPE Synergy 40Gb F8 Switch Module Command Line Interface (CLI) Guide' (dated 2019).
I suppose, 'HPE Synergy 40Gb F8 Switch' and 'HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy' are two different modules, and the 'HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy' actually does not support a command line interface, right?
In general: a command line interface is only supported when referenced in the QuickSpecs. But if referenced there, it can be accessed by the user.
Regards
Christof
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-12-2019 10:49 AM
03-12-2019 10:49 AM
Solution---
L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast.
https://www.avast.com/antivirus
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2021 05:13 PM
01-11-2021 05:13 PM
Re: Command Line Interface for HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy?
yes command line is available for virtual connect, but you need to enable the netop password using restful API
try using this powershell script
https://github.com/steem-supporter/synergy-powershell/blob/master/netop_pass-v02.ps1
also dont forget to assing IP to switches through oneview , use enclosure group to configure them and then update the LE from the group
Cheers