Music on Hold

[danieldunn10]

Hi, is it possible to set up an NBX V3000 so that when a caller is put on hold music is played in the background?

I have found the music on hold setting in the system wide settings, but cannot find where you choose the music to play?

Thanks very much

[DanCarroll]

the moh is an external connection.

Radio, MP3 player, cd player etc.

[merlin_1]

Use a radio with an RCA type of jack and plug it into the nbx .Next go into system settings and enable music on hold and music on transfer . Put a call on hold and listen to the back ground music . 

[danieldunn10]

Thanks for that, I can see the audio jack input, but when I plug it in and try the hold feature there is still no music. I've made sure the MOH option is ticked.

How can I adjust the volume, I can see there is a hole with volume marked on it on the front of the telephone system

Thanks

[kgregg]

I would call your cell phone or place a phone nearby on hold and adjust the volume of the input device. This is how I've always done it. Make sure that the incoming volume is not to high of it will clip when being played.

[merlin_1]

Once you plug into the jack , the connection is very simple . Make sure the radio is on , make sure both ends of the cable are plugged in . It should work as if the 2 check boxes are checked then thats all you have to do ....

I would check the music source  or a cable issue first .

[jenni.leister]

 Actually, for roughly $100 we bought a side plug in system... OnHold Plus 600, a MP3 digital on hold audio system... It's quite simple.. load the MP3s into its memory, press play, opt for repeat of all tracks and then press play... I adjusted volume once.. never again... I can also record my own messages if I want to and have them play on and off with audio tracks....

[maknbx_1]

Hi,

if in the NBX V3001BRI th volume of MOH/MOT is very low wath i do?

In my case i try with sound card of PC or MP3 withc cable jack 3,5", and the PC and MP3 player is function, but when connect intoa NBX the volume is very low also the volume of device is to high.

Previous customer's NBX100 have the volume on the NCP card, and the same PC with same cable function the MOH/MOT, is there any method with bring up the volume on the NBX V3001BRI?

Thanks

[DanCarroll]

3kb23123.

To change the volume connect to console and type--

mohSetVol (0 - 15) 0 is lowest 15 highest

to Check setting

type mohGetVol <ret>

[maknbx_1]

Thanks very lot !!!!!!

Unfortunately my first way is knowledgebase, but only in this case i suppose, in bad method, that this command i cannot find......

SORRY

and many thanks

[merlin_1]

Somebody snuck this by me ....

DanCarroll , who gave this to you ?

Subject:	How to change Music-on-Hold volume
Goals:
Symptoms:	How to change Music on hold volume MOH volume too soft MOH volume too loud
Changes:
Facts:	NBX 3Com NBX V300 Note 1. Setting takes effect on the next call. No need to reboot the box. 2. Setting will stay as you set it even through a power outage.
Causes:	Music on Hold Volume does not have a hardware setting on the V3000/V3001/V3001R as it does on the NBX100 and V5000.
Fixes:	To change the volume, connect to the console and type mohSetVol (0-15). Zero is the lowest setting, 15 is the highest. To check the setting , type mohGetVol <ret> and this will show you the setting.
Notes:
Product(s):	NBX
Sub Product(s):	3Com NBX V3000

Date Article Modified:

2008-06-11

[DanCarroll]

 I did a search on the knowledge base.

search term was---v3001r and moh.

[DanCarroll]

I did a knowledge base search

search term was--v3001r and moh