- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- Re: Bridge Aggregation MSR3012
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-30-2020 08:07 PM
03-30-2020 08:07 PM
Bridge Aggregation MSR3012
Hi All,
I am trying to create link aggregation on MSR3012 on ports GE0/1 and GE0/2. I am using the below commands:
interface Bridge-Aggregation 1
link-aggregation mode dynamic
then I go to GE0/1 and run the following command port link-aggegation group 1 and get the bellow error:
The link aggregation group does not exist.
please advice.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2020 05:49 AM - last edited on 04-01-2020 10:51 PM by Parvez_Admin
03-31-2020 05:49 AM - last edited on 04-01-2020 10:51 PM by Parvez_Admin
Re: Bridge Aggregation MSR3012
Hello! @ZainChaudhry
It happens, because ports Ge0/1 and Ge0/2 seem to be in routed mode. Unfortunately, these ports can't be used in bridged mode, unless be used only for the EVI feature. Try to enter "port link-mode bridge" under these interfaces context and you should see that warning message (don't forget to enable 'terminal monitor' in the console session in order to see the message, otherwise check with 'display logbuffer reverse')
The viable alternative would be a Route-Aggregation with sub-interfaces. It is practically the same as Bridge-Aggregation with Vlan-interfaces.
Example:
interface vlan 10
ip address 10.0.10.1 24
interface vlan 20
ip address 10.0.20.1 24
interface Bridge-Aggregation1
port link-type trunk
port trunk permit vlan 10,20
can be represented as:
interface Route-Aggregation1
#
interface Route-Aggregation1.10
ip address 10.0.10.1 24
vlan-type dot1q vid 10
#
interface Route-Aggregation1.20
ip address 10.0.20.1 24
vlan-type dot1q vid 20
Hope it helps!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-10-2020 01:14 PM - last edited on 04-12-2020 10:04 PM by Vajith V
04-10-2020 01:14 PM - last edited on 04-12-2020 10:04 PM by Vajith V
Re: Bridge Aggregation MSR3012
The HPE MSR3000 Switch Arrangement is a particular stage with a wide scope of availability choices that empowers the correct structure for your requirements.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-29-2020 07:34 AM
04-29-2020 07:34 AM
Re: Bridge Aggregation MSR3012
Hi @ZainChaudhry !