- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: FCIP Replication performance problems
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2006 01:37 AM
тАО10-19-2006 01:37 AM
FCIP Replication performance problems
EVA3000 - VCS 3028
EVA4000 - XCS 5031
Two independent fiber links (dedicated to CA) with bulk electronic in it, that delivers 30-75 Mbits/sec. Length is less than 10 Km.
2 + 2 SR2122 with only FCIP protocol, dedicated to CA.
In the performance test phase we use Command View to manage CA activity. No SRM installed.
Ping letency for 2KBytes packets are 4 ms (round trip). FTP bandwith is over 8MB/sec average. We measure this using two hosts that use this line.
Using the performance estimator we should have arround 100-115 I/Os sec (block=16KB) and trip latency of 2ms and low line usage.
Now the reality ... very sad data:
- Full Copy of one single copy set in one DR group takes for ever ... 0,6 MB/sec. Using EVAperf drt we get latency of more than 1000 ms.
- Host I/O (iometer) of 16KB (full writes) gives arround 2 I/Os/sec
During the test there are no other significant load on the EVA3000 and NO load at all on the EVA4000. The line is dedicated to CA all the time.
The obvious answer is that the problem is the line speed. Said that, way the ping & ftp numbers are good and the CA are so bad ??
Have you had similar experience in other FCIP replications ??
Any help or experience sharing will be appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2006 09:57 AM
тАО10-19-2006 09:57 AM
Re: FCIP Replication performance problems
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2006 06:25 PM
тАО10-19-2006 06:25 PM
Re: FCIP Replication performance problems
We don't use the Brocade MPR.
The switches are SAN switch 2/16 & 2/16V.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2006 06:34 PM
тАО10-19-2006 06:34 PM
Re: FCIP Replication performance problems
Reading the SR2122 Getting Started Guide
P/N=AA-RTE1G-TE
page 62 ...
regarding the parameter "useBport"
you can see:
Use Fibre Channel (FC) B_port connectivity. This configuration option applies
to all FCIP connection types. By default, the useBport setting is enabled.
However, the setting is dependent on the Fibre Channel switches and switch
firmware in use:
├в B-series
├в useBport disabled (B-series FW 3.2.x or 4.4.x or later)
├в useBport enabled (other B-series switch FW)
├в C-series - useBport disabled (MDS FW v2.01b or later)
├в M-series - useBport enabled
My switches versions are 5.1.x & 3.2.x so I have to disable useBport.
After that I get 250 I/O/sec doing iometer on a replicated disk and arround 4MB/sec bandwidth.
So, take care with this parameters !!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-17-2007 09:44 AM
тАО04-17-2007 09:44 AM
Re: FCIP Replication performance problems
From time to time (once or twice per week) we got communications problems between the SR's.
Link drop and after few second/minutes link come up again.
We have two lines, 4 SR2122-2 for FCIP.
In one of our lines, as soon as the line comes up, we can see automatic FLOGI from the SR and the CA activity resumes.
In the other line, when the link comes up, nothing happend.--> connection down for ever.
To fix that, I need to disable/enable the FC switch port where the SR is, in this way the SR logs in again to the fabric.
As far as I can see, all the elements in the two lines are similar. Way then this big difference reaction?
Where can I start debugging this ?
Thanks in advance.
antonio
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2007 12:31 PM
тАО05-28-2007 12:31 PM
Re: FCIP Replication performance problems
http://h18006.www1.hp.com/products/storageworks/fcipd_gateway/index.html?jumpid=reg_R1002_USEN
Shaun