- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: FW synchronization algorithm when replacing P2...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2020 11:25 PM - last edited on тАО02-19-2020 08:31 PM by Parvez_Admin
тАО02-18-2020 11:25 PM - last edited on тАО02-19-2020 08:31 PM by Parvez_Admin
FW synchronization algorithm when replacing P2000 MSA G3 controller
G4/G5ф╕Цф╗гуБоMSAуБоSMUуГкуГХуВбуГмуГ│уВ╣уВмуВдуГЙуБлуБпф┐ЭхоИщГихУБуБоуВ│уГ│уГИуГнуГ╝уГйуГ╝ф║дцПЫуВТхоЯцЦ╜уБЧуБЯха┤хРИуАБхЕГуБоуВ│уГ│уГИуГнуГ╝уГйуГ╝уБЛуВЙф║дцПЫщГихУБуБ╕FWуБМхРМцЬЯуБХуВМуВЛуБиуБошиШш╝ЙуБМуБВуВЛуБМуАБP2000 MSA G3уБлуБпхРМцзШуБошиШш╝ЙуБМшжЛуБдуБЛуВКуБ╛уБЫуВУуБзуБЧуБЯуАВ
G3уБоMSAуВВхРМцзШуБоFWхРМцЬЯуВвуГлуВ┤уГкуВ║уГауБМхЛХф╜ЬуБЩуВЛуБоуБЛчв║шкНуБЧуБЯуБДуАВ
Google Translated
The SMU reference guide for the G4 / G5 generation MSA states that if a maintenance part controller is replaced, the FW will be synchronized from the original controller to the replacement part. Could not be located. I want to check if the same FW synchronization algorithm works for G3 MSA.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2020 07:15 AM
тАО02-20-2020 07:15 AM
Re: FW synchronization algorithm when replacing P2000 MSA G3 controller
Hi,
go to the CLI and enter:
show advanced-settings
Look for
Partner Firmware Upgrade
The command is:
set advanced-settings partner-firmware-upgrade enabled|disabled|on|off
Cali
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2020 07:27 AM
тАО02-20-2020 07:27 AM
Re: FW synchronization algorithm when replacing P2000 MSA G3 controller
For the P2000 (MSA2000 G3) the controller with the newer firmware clones to the controller with the older firmware.
This is different to G4 and G5 (see above).
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!