Hewlett Packard Enterprise Community
Help
cancel
Turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 

P2000 G3 not updated firmware on one controller.

inetimon
Occasional Contributor
‎12-02-2015 04:17 AM
‎12-02-2015 04:17 AM

P2000 G3 not updated firmware on one controller.

P2000 G3 not updated firmware on one controller.

# show versions
Controller A Versions
---------------------
Bundle Version: TS252R007
Build Date: Fri May  8 15:40:57 MDT 2015

Controller B Versions
---------------------
Bundle Version: TS250P003
Build Date: Mon Aug 12 16:06:02 MDT 2013

 

 

How to update just one controller.
Thank you.

Tags (1)
0 Kudos
Reply
2 REPLIES 2
Torsten.
Acclaimed Contributor
‎12-02-2015 04:59 AM
‎12-02-2015 04:59 AM

Re: P2000 G3 not updated firmware on one controller.

Did you start the update recently?

How?

 

 

To update the single controller, disable PFU (partner firmware update) in settings, then use the GUI firmware page to update, this updates the controller you are connected to.

 

 

Be careful, if you startet an update with PFU enabled recently, it may be still in progress. This can take up to 1.5 hours.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
0 Kudos
Reply
Highlighted
inetimon
Occasional Contributor
‎12-02-2015 08:21 PM
‎12-02-2015 08:21 PM

Re: P2000 G3 not updated firmware on one controller.

 

Yes updated recently.

After the update it's been longer than 12 hours.

Updated via GUI download from the HP website (Online ROM Flash Component for Windows - HP P2000 G3 MSA Arrays).

Controller is in the state Degraded . State controller at the moment

 

# show controllers
Controllers
-----------
Controller ID: A
Serial Number: CN831........
Hardware Version: 53
CPLD Version: 22
MAC Address: 00:C0:FF:00:9D:00
WWNN: 20800.....................
IP Address: 10.
IP Subnet Mask: 255.255.255.0
IP Gateway: 10.
Disks: 24
Vdisks: 2
Cache Memory Size (MB): 2048
Host Ports: 2
Disk Channels: 2
Disk Bus Type: SAS
Status: Operational
Failed Over to This Controller: Yes
Fail Over Reason: Boot handshake timeout
Health: Degraded
Health Reason: A subcomponent of this component is unhealthy.
Health Recommendation: - No action is required.
Position: Top
Phy Isolation: Enabled
Controller Redundancy Mode: Fail Over
Controller Redundancy Status: Operational but not redundant

Controllers
-----------
Controller ID: B
Serial Number: CN831........
Hardware Version:
CPLD Version:
MAC Address: 00:00:00:00:00:00
WWNN: 20800...................
IP Address: 10.
IP Subnet Mask: 255.255.255.0
IP Gateway: 10.
Disks: 24
Vdisks: 2
Cache Memory Size (MB): 2048
Host Ports: 2
Disk Channels: 2
Disk Bus Type: SAS
Status: Down
Failed Over to This Controller: No
Fail Over Reason: Not applicable
Health: Fault
Health Reason: The controller is not operational.
Health Recommendation: - Restart the Storage Controller in this controller modul
e, unless it is performing an operation where it is normal for it to be shutdown
, such as firmware update.
Position: Bottom
Phy Isolation: Enabled
Controller Redundancy Mode: Fail Over
Controller Redundancy Status: Operational but not redundant

 

0 Kudos
Reply