- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: Tru64 Boot on SAN MSA 1000
MSA Storage
1783193
Members
1679
Online
109144
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-08-2004 04:20 AM
04-08-2004 04:20 AM
Tru64 Boot on SAN MSA 1000
Dear All,
I`m trying to configure boot on SAN from Alpha sistem running Tru64 UNIX with MSA1000.
I`m using two HBA adapters (FCA-2354)with latest available firmware configured for fabric topology.
MSA1000 have two 2/8FC shitches.
MSA 1000 controllers are configured for Tru64.
There is no problem to access and use all LUN`s configured on MSA 1000 when system is booted from local system disk.
In console mode, after WWIDMGR -QUICKSET command, all LUN`s are recognized by the system with message that they can be used after INIT command.
When I submit INIT command,on a next boot,there is no any information about previously detected MSA 1000 LUN`s.
Any suggestions or similar expirience?
Regards,
Goran
I`m trying to configure boot on SAN from Alpha sistem running Tru64 UNIX with MSA1000.
I`m using two HBA adapters (FCA-2354)with latest available firmware configured for fabric topology.
MSA1000 have two 2/8FC shitches.
MSA 1000 controllers are configured for Tru64.
There is no problem to access and use all LUN`s configured on MSA 1000 when system is booted from local system disk.
In console mode, after WWIDMGR -QUICKSET command, all LUN`s are recognized by the system with message that they can be used after INIT command.
When I submit INIT command,on a next boot,there is no any information about previously detected MSA 1000 LUN`s.
Any suggestions or similar expirience?
Regards,
Goran
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-08-2004 07:35 AM
04-08-2004 07:35 AM
Re: Tru64 Boot on SAN MSA 1000
Goran,
I have just written an answer in the following thread - please let us continue the discussion there:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=543834
I have just written an answer in the following thread - please let us continue the discussion there:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=543834
.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP