- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Added SCSI disk to 9000 Class A but can not see th...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 01:09 AM
08-23-2007 01:09 AM
Added SCSI disk to 9000 Class A but can not see the disk
Hi
I have added a 146GB SCSI disk to A class 9000 HP server running HP-UX 11v1 via a dual port SCSI host bus adapter. I am able to see the adapter but can not see the new disk. Server has 1 internal disk with OS on it. Please post your suggestions about possibilities.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 01:12 AM
08-23-2007 01:12 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 01:13 AM
08-23-2007 01:13 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
insf -C disk
ioscan -fnC disk
Try again.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 01:14 AM
08-23-2007 01:14 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
model command.
We work a lot with these systems and some of the earlier ones could not see very large disks.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 01:16 AM
08-23-2007 01:16 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
Is the HBA supported for this server and CLAIMED?
Is the bus terminated?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 02:47 AM
08-23-2007 02:47 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
I have run insf command, rebooted server, SCSI interfaces are terminating properly.
Disk specs are:
Seagate brand
Cheetah 10K.7
Ultra U320 SCSI Drive
Model# ST373207LW
RPM: 10K
Serial# 3KT0QXGF
Disk is connects via dual port SCSI host bus adapter and I can see bus adapter but not the disk.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 04:13 AM
08-23-2007 04:13 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 04:22 AM
08-23-2007 04:22 AM
Re: Added SCSI disk to 9000 Class A but can not see the disk
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-23-2007 07:59 PM
08-23-2007 07:59 PM
Re: Added SCSI disk to 9000 Class A but can not see the disk
Model# ST373207LW
ST = Seagate
First 3 = 3 inch size
73 = 73GB
What SCSI ID is the disk set to ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-29-2007 12:42 PM
08-29-2007 12:42 PM
Re: Added SCSI disk to 9000 Class A but can not see the disk
(Since the forums provide no means of
communicating to other posters (outside a thread, AFAIK ...
you didn't assign points in the
"Do you know ftp location for
PF_CHAW4350.tar.gz?" thread!
Back to your SCSI disk ...
can you see it via a "SEA" (search) command
below the ISL prompt level? (That's a firmware implemented command.)
Stan
sieler@allegro.com