- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: console problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 05:16 AM
12-27-2001 05:16 AM
We have a K210 model and am installing hpux11.00 on it. First I want to know whether K210 model supports 11.00, 32 bit or not?
Additionly, while installing I am stuck up at the console prompt...machine is booting up...but i can't retrieve output on console...although I switch on/off consolee it just shows the same bottom menu of "Auto" etc. how to get rid of this menu?
pl help !!!!
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 05:39 AM
12-27-2001 05:39 AM
Solutionfirst K-210 in support by hp-ux 11.00 .
i have this k-class in our office and i install over there 11i and also 11.00
this is for your first que.
about your second que.
check the key in the computer to see if it is on service or hold .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 05:43 AM
12-27-2001 05:43 AM
Re: console problem
the server key is in "on" mode only.
Whenever we r putting it on we r getting user interface menu direrctly so I think that this may be the problem. Eventhough I am resetting the monitor I gets user interface menu....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 06:04 AM
12-27-2001 06:04 AM
Re: console problem
The steps to put the terminal into REMOTE MODE (and out of BLOCK MODE if necessary) or to change the emulation depend on the terminal you are using.
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 06:18 AM
12-27-2001 06:18 AM
Re: console problem
Thanks a lot..atlast I am able to get into. It starts showing the booting process on the console. But the new prob is If I enter any command at "MENU" prompt say "boot P6" then it shows "Error : unknown commnad". what may be the possible reasons....any key sequence of terminal U suggest for the same?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-27-2001 07:48 AM
12-27-2001 07:48 AM
Re: console problem
I have experienced the same problem. Look like you have some problems with the terminal settings. Choose the terminal emulation as "HP". If needed, select "7 bit and odd parity" or "8 bit no parity". This depend on your terminal type. You need to play around with that.
HTH,
Shiju
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-28-2001 10:58 PM
12-28-2001 10:58 PM
Re: console problem
Now we r facing a different poblem. We are able to install hpux11.00 os on HPK210 model server. I want to add a disk of 36 GB capacity to the server for additional work load. It's a scsi disk. If I connect it to the scsi port of k210, my k210 server doesn't boot at all. After removing the disk it behaves well. I checked for scsi id conflict but there seems tobe no problem. Have you ever connected an additional scsi disk to k210 server?
pl reply asap.