error in ignite Backup

[cabloy]

Hi...
I just run make_recovery -v -A -d /dev/rmt/0m and received the following error:

message=N::Boot device is: 1/0/0/3/0.6.0

# ACTION NAME:CONFIG_SAVE

save_config: Error - get_system_info failed to get IO information from IO listener.
ERROR: /opt/ignite/bin/save_config failed.

Can someone please help me resolved this issue? Currently were running on HPUX 11.23 RX7640.

For your reference below is the output file of lvmtab,bdf,lvnlboot.
# strings /etc/lvmtab
/dev/vg00
/dev/dsk/c0t6d0s2
/dev/dsk/c3t6d0s2
/dev/vg01
/dev/dsk/c11t0d2
/dev/vg02
/dev/dsk/c11t0d0
/dev/dsk/c11t0d1
# lvlnboot -v
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
/dev/dsk/c0t6d0s2 (1/0/0/3/0.6.0) -- Boot Disk
/dev/dsk/c3t6d0s2 (1/0/1/1/0/4/1.6.0) -- Boot Disk
Boot: lvol1 on: /dev/dsk/c0t6d0s2
/dev/dsk/c3t6d0s2
Root: lvol3 on: /dev/dsk/c0t6d0s2
/dev/dsk/c3t6d0s2
Swap: lvol2 on: /dev/dsk/c0t6d0s2
/dev/dsk/c3t6d0s2
Dump: lvol2 on: /dev/dsk/c0t6d0s2, 0

# vgdisplay -v /dev/vg00
--- Volume groups ---
VG Name /dev/vg00
VG Write Access read/write
VG Status available
Max LV 255
Cur LV 10
Open LV 10
Max PV 16
Cur PV 2
Act PV 2
Max PE per PV 4356
VGDA 4
PE Size (Mbytes) 32
Total PE 8702
Alloc PE 3239
Free PE 5463
Total PVG 0
Total Spare PVs 0
Total Spare PVs in use 0

--- Logical volumes ---
LV Name /dev/vg00/lvol1
LV Status available/syncd
LV Size (Mbytes) 1792
Current LE 56
Allocated PE 112
Used PV 2

LV Name /dev/vg00/lvol2
LV Status available/syncd
LV Size (Mbytes) 8192
Current LE 256
Allocated PE 512
Used PV 2

LV Name /dev/vg00/lvol3
LV Status available/syncd
LV Size (Mbytes) 800
Current LE 25
Allocated PE 50
Used PV 2

LV Name /dev/vg00/lvol4
LV Status available/syncd
LV Size (Mbytes) 2016
Current LE 63
Allocated PE 126
Used PV 2

LV Name /dev/vg00/lvol5
LV Status available/syncd
LV Size (Mbytes) 3008
Current LE 94
Allocated PE 188
Used PV 2

LV Name /dev/vg00/lvol6
LV Status available/syncd
LV Size (Mbytes) 8448
Current LE 264
Allocated PE 528
Used PV 2

LV Name /dev/vg00/lvol7
LV Status available/syncd
LV Size (Mbytes) 7360
Current LE 230
Allocated PE 460
Used PV 2

LV Name /dev/vg00/lvol8
LV Status available/syncd
LV Size (Mbytes) 8704
Current LE 272
Allocated PE 544
Used PV 2

LV Name /dev/vg00/lvol9
LV Status available/syncd
LV Size (Mbytes) 15008
Current LE 469
Allocated PE 469
Used PV 1

LV Name /dev/vg00/lvswap
LV Status available/syncd
LV Size (Mbytes) 8000
Current LE 250
Allocated PE 250
Used PV 1


--- Physical volumes ---
PV Name /dev/dsk/c0t6d0s2
PV Status available
Total PE 4346
Free PE 2367
Autoswitch On

PV Name /dev/dsk/c3t6d0s2
PV Status available
Total PE 4356
Free PE 3096
Autoswitch On

[Ramesh S · Accepted solution]

Hi

Because, it's checking every device to see if it is a boot device on a PA system.

I would suggest you to install latest version of ignite and try...

Also, have a look on these threads

http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=7162&admit=-682735245+1187582913706+28353475
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=95102&admit=-682735245+1187583008497+28353475

Thanks & Regards

Ramesh

[cabloy]

Hi

Is it safe to install a new version of Ignite? please take note that that the system is currently in production.

Please advice...

Thanks,

[Robert-Jan Goossens]

Yes you can savely upgrade the Ignite software, no reboot required.

Could you post the complete error ooutput from youur ignite command, and why are you using make_recovery? This is the old recovery command, you should use the make_tape_recovey command.

Best regards,
Robert-Jan

[Shrikant Lavhate]

Hi,

Check print_manifest runs smoothly or not. Updating ignite dosnt harm your system. It dosnt require any reboot too.

[Torsten.]

Not related to this problem, but why you have an unmirrored swap?

LV Name /dev/vg00/lvswap
LV Status available/syncd
LV Size (Mbytes) 8000
Current LE 250
Allocated PE 250
Used PV 1


If this disk fails, your system will most likely crash ...

[Torsten.]

... and now related to problem:

You did a

make_recovery -v -A -d /dev/rmt/0m

but it should be

make_tape_recovery -v -A -a /dev/rmt/0mn

[cabloy]

Hey guys.....it was a typo error. We used the command make_tape_recovery.

Hi Torsten thanks..we wiill just mirror the logical swap.

thanks to all for your immediate reply we will just update you once we upgrade the ignite software.

- cabloy