Operating System - HP-UX
1755730
Members
3619
Online
108837
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2001 07:39 AM
тАО05-10-2001 07:39 AM
I do not have the GSP configured on a Lan port but I have the ATTN amber flashing light on all the time. Should I be concerned?
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2001 07:45 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2001 07:46 AM
тАО05-10-2001 07:46 AM
Re: GSP
Hi,
Just to make sure, I would connect GSP:
At the console type
CTRL-B then at the prompt type SL, to see what is logged: e, and to leave quit =q
and co to return at the console...
All the best
Victor
Just to make sure, I would connect GSP:
At the console type
CTRL-B then at the prompt type SL
and co to return at the console...
All the best
Victor
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2001 07:57 AM
тАО05-10-2001 07:57 AM
Re: GSP
If you want show log of GSP with Accessing Guardian Service Processor Internal Port:
The Guardian Service Processor (GSP) internal port can be used as a "back door" to reset
security options in case the GSP administrator password is forgotten, for example. It can
also be used in order to upgrade the GSP firmware from an HP-UX session. The internal
port needs to be configured in order to use it.
1. On the system, the GSP internal port should be /dev/tty1p0.
2. SAM does not configure the GSP internal port.
3. If the device file is not present, it can be created as follows:
#cd/dev
#mknod tty1p0 c 1 0x010000
4. Since this allows unrestricted access to the GSP and bypasses GSP security features (no
user or password required). Make sure to delete this device file when you have finished
using it.
5. The internal port can be accessed via terminal emulators such as cu. To use cu, you
need the follow entries (the entries must be exactly as shown):
/usr/lib/uucp/Systems needs the following entry:
gspiport Any;5 gspiport,f900 - ''''\r\d\r\d\r ogin:-BREAK-ogin:
uucp asswrd: uucp-BREAK-ogin: uucp asswrd: uucp
The spelling looks unusual, but it needs to be exactly as shown.
/usr/lib/uucp/Devices needs the following entry:
gspiport tty1p0 - 9600 direct
6. when all of the configuration is done, you should be able to access the GSP internal port
with the cu command:
cu-1/dev/tty1p0
7. To terminate the cu session, use "~." [return]
8. Kermit can also be used to access the special device file. See the kermit web pages for
details.
CAUTION Securing the /dev/tty1p0 device file with root capabilities will not prevent
non-root users from accessing the GSP internal port. This is due to the fact
that cu and kermit carry root access and run with the sticky bit enabled.
To secure the internal port from unauthorized use, be sure to remove the
/dev/tty1p0 file after using it.
The Guardian Service Processor (GSP) internal port can be used as a "back door" to reset
security options in case the GSP administrator password is forgotten, for example. It can
also be used in order to upgrade the GSP firmware from an HP-UX session. The internal
port needs to be configured in order to use it.
1. On the system, the GSP internal port should be /dev/tty1p0.
2. SAM does not configure the GSP internal port.
3. If the device file is not present, it can be created as follows:
#cd/dev
#mknod tty1p0 c 1 0x010000
4. Since this allows unrestricted access to the GSP and bypasses GSP security features (no
user or password required). Make sure to delete this device file when you have finished
using it.
5. The internal port can be accessed via terminal emulators such as cu. To use cu, you
need the follow entries (the entries must be exactly as shown):
/usr/lib/uucp/Systems needs the following entry:
gspiport Any;5 gspiport,f900 - ''''\r\d\r\d\r ogin:-BREAK-ogin:
uucp asswrd: uucp-BREAK-ogin: uucp asswrd: uucp
The spelling looks unusual, but it needs to be exactly as shown.
/usr/lib/uucp/Devices needs the following entry:
gspiport tty1p0 - 9600 direct
6. when all of the configuration is done, you should be able to access the GSP internal port
with the cu command:
cu-1/dev/tty1p0
7. To terminate the cu session, use "~." [return]
8. Kermit can also be used to access the special device file. See the kermit web pages for
details.
CAUTION Securing the /dev/tty1p0 device file with root capabilities will not prevent
non-root users from accessing the GSP internal port. This is due to the fact
that cu and kermit carry root access and run with the sticky bit enabled.
To secure the internal port from unauthorized use, be sure to remove the
/dev/tty1p0 file after using it.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP