Having ignite issues when trying to restore a server from tape

[sujit kumar singh]

Hi

sorry for the typo in theearlier post.

the Shell command written as rconnect -r is

Shell>reconnect -r

regards
sujit

[Joe Profaizer]

Same exact result as before:

* Sun Feb 01 05:52:00 EST 2009: Completed archive load of the source
(Recovery Archive).
* Executing user specified script:
"/opt/ignite/data/scripts/os_arch_post_l".
* Running in recovery mode (os_arch_post_l).
* Relocating RAM filesystems.
* Running the ioinit command ("/sbin/ioinit -c")
* Creating device files via the insf command.
insf: Installing special files for sdisk instance 2 address 0/0/3/0.0.0.0
insf: Installing special files for sdisk instance 1 address 0/1/1/0.0.0
insf: Installing special files for sdisk instance 0 address 0/1/1/0.1.0
insf: Installing special files for esdisk instance 4 address 64000/0xfa00/0x2
insf: Installing special files for esdisk instance 3 address 64000/0xfa00/0x3
insf: Installing special files for esdisk instance 5 address 64000/0xfa00/0x4
insf: Installing special files for stape instance 0 address 0/1/1/0.6.0
insf: Installing special files for estape instance 4 address 64000/0xfa00/0x0
insf: Installing special files for pseudo driver dlpi
insf: Installing special files for pseudo driver kepd
insf: Installing special files for pseudo driver framebuf
insf: Installing special files for pseudo driver sad
* Creating the system file.
Creating your system file in the file /tmp/ign_configure/tstand.system
* Constructing the bootconf file.
* Setting primary boot path to "/dev/rdisk/disk4".
Primary boot path set to 0/1/1/0.0x1.0x0 (/dev/rdisk/disk4)
NOTE: Skipping hwpath: "0/0/3/0.0.0" class: "target" new_instance: "11"
because instance number does not need to remain persistent.
NOTE: Skipping hwpath: "0/1/1/0.0" class: "target" new_instance: "1" because
instance number does not need to remain persistent.
NOTE: Skipping hwpath: "0/1/1/0.1" class: "target" new_instance: "0" because
instance number does not need to remain persistent.
NOTE: Skipping hwpath: "0/1/1/0.6" class: "target" new_instance: "12"
because instance number does not need to remain persistent.
NOTE: Skipping hwpath: "0/1/1/0.4" class: "target" new_instance: "2" because
instance number does not need to remain persistent.
* Executing: "/var/adm/sw/products/OS-Core/CORE-SHLIBS/iux_postload".
* Running: /var/adm/sw/products/OS-Core/CORE-SHLIBS/postinstall
* Executing: "/var/adm/sw/products/OS-Core/CORE2-KRN/iux_postload".
* Executing: "/var/adm/sw/products/OS-Core/CORE-KRN/iux_postload".
* Executing: "/var/adm/sw/products/FC-FCD/FC-FCD-KRN/iux_postload".
* Loading_software: Complete
======= 02/01/09 04:52:17 CST Building the new kernel.
* Build_Kernel: Begin
* Building a new kernel using the command: "/usr/sbin/mk_kernel -f -o
/stand/vmunix".
* The currently running configuration has been imported from
'/stand/system'.
* Build_Kernel: Complete
* Boot_From_Client_Disk: Begin
======= 02/01/09 04:53:13 CST Rebooting machine as expected.
NOTE: Rebooting system.
Calling function e000000001d980e0 for Shutdown State 1 type 0x1

sync'ing disks (0 buffers to flush):
0 fcache pages still dirty
0 buffers not flushed
0 buffers still dirty
Calling function e00000000299ff50 for Shutdown State 5 type 0x1
Calling function e000000002032bb0 for Shutdown State 5 type 0x1

Closing open logical volumes...
Done
***********************************************************
* ROM Version : 04.29
* ROM Date : 12/10/2007
* BMC Version : 04.06
***********************************************************
0 0 0x0015B2 0x0000000021721057 boot time event
1 0 0x0000A4 0x0000000000000000 start memory configuration
0 0 0x0015B2 0x0000000057372928 boot time event
1 0 0x000014 0x0000000000000000 CPU0 starting cell relocation
1 0 0x000009 0x0000000000000000 CPU0 launch EFI
EFI version 1.10 [14.62]
EFI64 Running on Intel(R) Itanium Processor Family
EFI 1.10 IPF server rx4640 5.48 [Thu Nov 10 15:08:03 2005] firmware by HP
Loading 'SysROM:Floating-Point Software Assistance Handler'...
-- 'SysROM:Floating-Point Software Assistance Handler' returned Success
Loading 'SysROM:Broadcom Gigabit Ethernet Driver'...

Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.10

-- 'SysROM:Broadcom Gigabit Ethernet Driver' returned Success
Loading 'SysROM:SCSI Bus Driver'...
-- 'SysROM:SCSI Bus Driver' returned Success
Loading 'SysROM:SCSI Tape Driver'...
-- 'SysROM:SCSI Tape Driver' returned Success
Loading device drivers
































EFI Boot Manager ver 1.10 [14.62] OS might use only the primary console set via boot manager or conconfig command
/----------------------------------\ /----------------------------------\ | System Overview | | Boot Menu | | hp server rx4640 | | HP-UX Primary Boot: 0/1/1/0.... | | Serial #: USE4414736 | | Core LAN Gb A | | | | EFI Shell [Built-in] | | System Firmware: 4.29 [4750] | | Boot Disk | | BMC Version: 4.06 | | Internal Bootable DVD | | MP Version: E.03.32 | | DAT Drive | | Installed Memory: 32768 MB | | ------------------------------- | | | | Boot Configuration | | CPU Logical | | System Configuration | | Module CPUs Speed Status | | Security Configuration | | 0 1 1.5 GHz Active | | | | 1 1 1.5 GHz Active | \----------------------------------/ | 2 1 1.5 GHz Active | | 3 1 1.5 GHz Active | | | | | \----------------------------------/
Use <^|v> to scroll to Select or for Previous Menu

Scsi(Pun1,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Loading.: HP-UX Primary Boot: 0/1/1/0.0x1.0x0
Starting: HP-UX Primary Boot: 0/1/1/0.0x1.0x0

(C) Copyright 1999-2008 Hewlett-Packard Development Company, L.P.
All rights reserved

HP-UX Boot Loader for IPF -- Revision 2.036

Press Any Key to interrupt Autoboot
\EFI\HPUX\AUTO ==> boot vmunix
Seconds left till autoboot - 0
AUTOBOOTING...> System Memory = 32739 MB
loading section 0
.................................................................................. (complete)
loading section 1
............. (complete)
loading symbol table
loading System Directory (boot.sys) to MFS
.....
loading MFSFILES directory (bootfs) to MFS
.....................

================================================================================
WARNING: Multiple console output devices are configured. If this message
remains on the screen for more than a few minutes, then this is not the
device in use by HP-UX as the console output device. If you would like this
device to be the one used by HP-UX as the console ouput device, reboot and
use the EFI boot manager or the EFI 'conconfig' command to select this device
and deconfigure the others.
================================================================================

Launching /stand/vmunix
SIZE: Text:41544K + Data:6397K + BSS:21890K = Total:69832K
Console is on Serial Device - via PCDP
Booting kernel...

Loaded ACPI revision 2.0 tables.
Using /stand/ext_ioconfig

Memory Class Setup
-------------------------------------------------------------------------
Class Physmem Lockmem Swapmem
-------------------------------------------------------------------------
System : 31139 MB 31139 MB 31139 MB
Kernel : 31139 MB 31139 MB 31139 MB
User : 29880 MB 26490 MB 26593 MB
-------------------------------------------------------------------------

Starting ktracer 0 1
Installing Socket Protocol families AF_INET and AF_INET6
Kernel EVM initialized
sec_init(): kernel RPC authentication/security initialization.
secgss_init(): kernel RPCSEC_GSS security initialization.
rpc_init(): kernel RPC initialization.
rpcmod_install(): kernel RPC STREAMS module "rpcmod" installation. ...(driver_install)
NOTICE: nfs_client_pv3_install(): nfs3 File system was registered at index 11.
NOTICE: nfs_client_pv4_install(): nfs4 File system was registered at index 12.
NOTICE: cachefsc_install: cachefs File system was registered at index 14.
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/2/1/0
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/5/1/0
Boot device's HP-UX HW path is: 0.1.1.0.1.0

System Console is on the Built-In Serial Interface
igelan0: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/1/2/0
AF_INET socket/streams output daemon running, pid 41
afinet_prelink: module installed
Starting the STREAMS daemons-phase 1
LVM: Root VG activated
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
The device file /dev/rroot does not exist or is not correct.
Automatic checks of the root file system not performed.
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: B.11.31_LR FLAVOR=perf
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 33524756 Kbytes, lockable: 25192804 Kbytes, available: 28475124 Kbytes

insf: Installing special files for sdisk instance 2 address 0/0/3/0.0.0.0
insf: Installing special files for sdisk instance 1 address 0/1/1/0.0.0
insf: Installing special files for sdisk instance 0 address 0/1/1/0.1.0
insf: Installing special files for esdisk instance 4 address 64000/0xfa00/0x2
insf: Installing special files for esdisk instance 3 address 64000/0xfa00/0x3
insf: Installing special files for esdisk instance 5 address 64000/0xfa00/0x4

[Joe Profaizer]

In addition when the system tried to reboot by itself the system crashed, below is the output:

Scsi(Pun1,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Loading.: HP-UX Primary Boot: 0/1/1/0.0x1.0x0
Starting: HP-UX Primary Boot: 0/1/1/0.0x1.0x0

(C) Copyright 1999-2008 Hewlett-Packard Development Company, L.P.
All rights reserved

HP-UX Boot Loader for IPF -- Revision 2.036

Press Any Key to interrupt Autoboot
\EFI\HPUX\AUTO ==> boot vmunix
Seconds left till autoboot - 0
AUTOBOOTING...> System Memory = 32739 MB
loading section 0
.................................................................................. (complete)
loading section 1
............. (complete)
loading symbol table
loading System Directory (boot.sys) to MFS
.....
loading MFSFILES directory (bootfs) to MFS
.....................

================================================================================
WARNING: Multiple console output devices are configured. If this message
remains on the screen for more than a few minutes, then this is not the
device in use by HP-UX as the console output device. If you would like this
device to be the one used by HP-UX as the console ouput device, reboot and
use the EFI boot manager or the EFI 'conconfig' command to select this device
and deconfigure the others.
================================================================================

Launching /stand/vmunix
SIZE: Text:41544K + Data:6397K + BSS:21890K = Total:69832K
Console is on Serial Device - via PCDP
Booting kernel...

Loaded ACPI revision 2.0 tables.
Using /stand/ext_ioconfig

Memory Class Setup
-------------------------------------------------------------------------
Class Physmem Lockmem Swapmem
-------------------------------------------------------------------------
System : 31139 MB 31139 MB 31139 MB
Kernel : 31139 MB 31139 MB 31139 MB
User : 29880 MB 26490 MB 26593 MB
-------------------------------------------------------------------------

Starting ktracer 0 1
Installing Socket Protocol families AF_INET and AF_INET6
Kernel EVM initialized
sec_init(): kernel RPC authentication/security initialization.
secgss_init(): kernel RPCSEC_GSS security initialization.
rpc_init(): kernel RPC initialization.
rpcmod_install(): kernel RPC STREAMS module "rpcmod" installation. ...(driver_install)
NOTICE: nfs_client_pv3_install(): nfs3 File system was registered at index 11.
NOTICE: nfs_client_pv4_install(): nfs4 File system was registered at index 12.
NOTICE: cachefsc_install: cachefs File system was registered at index 14.
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/2/1/0
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/5/1/0
Boot device's HP-UX HW path is: 0.1.1.0.1.0

System Console is on the Built-In Serial Interface
igelan0: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/1/2/0
AF_INET socket/streams output daemon running, pid 41
afinet_prelink: module installed
Starting the STREAMS daemons-phase 1
LVM: Root VG activated
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
The device file /dev/rroot does not exist or is not correct.
Automatic checks of the root file system not performed.

Stored message buffer up to system crash:

MFS is defined: base= 0xe000000101ba3000 size= 26788 KB
Loaded ACPI revision 2.0 tables.
MMIO on this platform supports Write Coalescing.


MCA recovery subsystem disabled, not supported on this platform.
Using /stand/ext_ioconfig

Memory Class Setup
-------------------------------------------------------------------------
Class Physmem Lockmem Swapmem
-------------------------------------------------------------------------
System : 31139 MB 31139 MB 31139 MB
Kernel : 31139 MB 31139 MB 31139 MB
User : 29880 MB 26490 MB 26593 MB
-------------------------------------------------------------------------

Starting ktracer 0 1
Installing Socket Protocol families AF_INET and AF_INET6
64000/0xfa00 esvroot
Kernel EVM initialized
sec_init(): kernel RPC authentication/security initialization.
secgss_init(): kernel RPCSEC_GSS security initialization.
rpc_init(): kernel RPC initialization.
rpcmod_install(): kernel RPC STREAMS module "rpcmod" installation. ...(driver_install)
NOTICE: nfs_client_pv3_install(): nfs3 File system was registered at index 11.
NOTICE: nfs_client_pv4_install(): nfs4 File system was registered at index 12.
NOTICE: cachefsc_install: cachefs File system was registered at index 14.
btlan_load() Loaded Successfully
0 sba
0/0 lba
0/0/1/0 asio0
0/0/1/1 asio0
0/0/2/0 UsbOhci
0/0/2/1 UsbOhci
0/0/2/2 UsbEhci
0/0/3/0 side_multi
0/0/3/0.0 side
0/0/3/0.1 side
0/0/3/0.0.0x0 estp
0/0/4/0 gvid_core
0/1 lba
0/1/1 pci_slot
c8xx BUS: 2 SCSI C1010 Ultra Wide Single-Ended A6829-60101 assigned CPU: 0
0/1/1/0 c8xx
c8xx BUS: 3 SCSI C1010 Ultra160 Wide LVD A6829-60101 assigned CPU: 3
0/1/1/1 c8xx
0/1/2 pci_slot
0/1/2/0 igelan
0/2 lba
0/2/1 pci_slot
0/1/1/0.0x6 estp
0/1/1/0.0x4 estp
0/1/1/0.0x6.0x0 eslpt
0/1/1/0.0x1 estp
0/1/1/0.0x4.0x0 eslpt
0/1/1/0.0x0 estp
0/1/1/0.6 tgt
0/1/1/0.6.0 stape
0/1/1/0.4 tgt
0/1/1/0.4.0 sctl
0/1/1/0.0x1.0x0 eslpt
0/1/1/0.1 tgt
0/1/1/0.1.0 sdisk
0/1/1/0.0x0.0x0 eslpt
0/1/1/0.0 tgt
0/1/1/0.0.0 sdisk
0/0/3/0.0.0x0.0x0 eslpt
0/0/3/0.0.0 tgt
0/0/3/0.0.0.0 sdisk
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/2/1/0
0/2/1/0 td
0/3 lba
0/3/1 pci_slot
0/3/2 pci_slot
0/4 lba
0/4/1 pci_slot
0/4/2 pci_slot
0/5 lba
0/5/1 pci_slot
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/5/1/0
0/5/1/0 td
120 processor
121 processor
122 processor
123 processor
250 pdh
250/0 ipmi
250/1 acpi_node
64000/0xfa00/0x0 estape
64000/0xfa00/0x1 esctl
64000/0xfa00/0x2 esdisk
64000/0xfa00/0x3 esdisk
64000/0xfa00/0x4 esdisk
Boot device's HP-UX HW path is: 0.1.1.0.1.0

System Console is on the Built-In Serial Interface
igelan0: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/1/2/0
AF_INET socket/streams output daemon running, pid 41
afinet_prelink: module installed
Starting the STREAMS daemons-phase 1
LVM: Root VG activated
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Dump device table: (start & size given in 1-Kbyte blocks)
entry 0000000000000000 - major is 3, minor is 0x2; start = 2349920, size = 8388608
VFS_MOUNTROOT error information:
0:(hfs) 22
1:(nfs) 223
6:(DevFS) 251
10:(vxfs) 28
11:(nfs3) 223
12:(nfs4) 223
13:(autofs) 251
16:(cifs) 223
18:(dnlc_neg_fs) 251

Message buffer contents after system crash:

panic: VFS_MOUNTROOT: RDWR: all VFS_MOUNTROOTs failed: NEED DRIVERS ?????
Stack Trace:
IP Function Name
0xe00000000205f2e0 vfs_mountroot+0x6c0
0xe0000000017bbdf0 im_preinitrc+0x450
0xe000000002050f40 DoCalllist+0x390
End of Stack Trace

linkstamp: Sun Feb 01 04:53:13 CST 2009
_release_version: @(#) $Revision: vmunix: B.11.31_LR FLAVOR=perf
Calling function e0000000018a8100 for Shutdown State 1 type 0x2
i 0 pfn 0x1 pages 0x9f
i 1 pfn 0x100 pages 0x3de24
i 2 pfn 0x3e23c pages 0x2ec
i 3 pfn 0x3fc00 pages 0x220
i 4 pfn 0x100000 pages 0x6ffffe
i 5 pfn 0x4040000 pages 0xbeffe
i 6 pfn 0x40ff000 pages 0xc4a
i 7 pfn 0x40ffc84 pages 0x18e
i 8 pfn 0x40ffe80 pages 0x162
*** Not enough CPUS for a compressed dump ***

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

*** The dump will be a SELECTIVE dump with
compression OFF and concurrency ON: 2658 of 32740 megabytes.
*** To change this dump type, press any key within 10 seconds.

*** Select one of the following dump types, by pressing the corresponding key:
C) Proceed with CURRENT dump configuration.
S) The dump will be a SELECTIVE dump with both compression and
concurrency OFF: 2658 of 32740 megabytes.
P) The dump will be a PARTIAL dump with both compression and
concurrency OFF: 8191 of 32740 megabytes.
(A FULL dump is not possible.)
N) There will be NO DUMP performed.
*** Enter your selection now.
ñ*** Invalid response. Please try again.

*** Select one of the following dump types, by pressing the corresponding key:
C) Proceed with CURRENT dump configuration.
S) The dump will be a SELECTIVE dump with both compression and
concurrency OFF: 2658 of 32740 megabytes.
P) The dump will be a PARTIAL dump with both compression and
concurrency OFF: 8191 of 32740 megabytes.
(A FULL dump is not possible.)
N) There will be NO DUMP performed.
*** Enter your selection now.
c*** Proceeding with selective dump, with compression off and concurrency on.



Primary Dump Header Location :
Device details:
Major number: 31 Minor number:0x21000
Offset: 2349920.
*** The dump may be aborted at any time by pressing ESC.
*** Dumping: 100% complete (2658 of 2658 MB)
time: 108 seconds, Number of Dump units: 1



I will try the SHELL> reconnect -r
What does this command do?

[Joe Profaizer]

map
reconnect -r (output)
map

Shell> map
Device mapping table
fs0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
fs1 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11D9-8002-D6217B60E588)
fs2 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11DD-8000-D6217B60E588)
fs3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)
blk1 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
blk2 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry1)
blk3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)
blk4 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11D9-8002-D6217B60E588)
blk5 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part2,Sig69542DAE-121A-11D9-8003-D6217B60E588)
blk6 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part3,Sig69542DCC-121A-11D9-8004-D6217B60E588)
blk7 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)
blk8 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11DD-8000-D6217B60E588)
blk9 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part2,Sig28E08F38-F046-11DD-8000-D6217B60E588)
blkA : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11DD-8000-D6217B60E588)

Shell> reconnect -r

Scsi(Pun0,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Scsi(Pun1,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Scsi(Pun4,Lun0) HP SAF-TE 1
Scsi(Pun6,Lun0) HP C5683A C908 ( 40 MBytes/sec)
Broadcom NetXtreme Gigabit Ethernet (BCM5701) is detected (PCI)

[Read only - use Ctrl-Ecf for console write access.]
ReconnectController(0,0,0) : Status = Success

Shell> map
Device mapping table
fs0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
fs1 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11D9-8002-D6217B60E588)
fs2 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11DD-8000-D6217B60E588)
fs3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)
blk1 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
blk2 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry1)
blk3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)
blk4 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11D9-8002-D6217B60E588)
blk5 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part2,Sig69542DAE-121A-11D9-8003-D6217B60E588)
blk6 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part3,Sig69542DCC-121A-11D9-8004-D6217B60E588)
blk7 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)
blk8 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11DD-8000-D6217B60E588)
blk9 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part2,Sig28E08F38-F046-11DD-8000-D6217B60E588)
blkA : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11DD-8000-D6217B60E588)

[sujit kumar singh · Accepted solution]

HI joe,

yes can see that...
just to confirm that the tape that used for the recovery was a newly created Ignite tape or was the same as you had first tried?

Ok think go ahead with the update of the ignite as ypu said on the source server.

wish you Luck this time.

regards
sujit

[Joe Profaizer]

It is a new tape with the latest ignite version.

[Joe Profaizer]

How can I tell which fs#: equates to the tape drive?

Scsi(Pun0,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Scsi(Pun1,Lun0) HP 73.4GST373453LC HPC4 ( 40 MBytes/sec)
Scsi(Pun4,Lun0) HP SAF-TE 1
Scsi(Pun6,Lun0) HP C5683A C908 ( 40 MBytes/sec)
Broadcom NetXtreme Gigabit Ethernet (BCM5701) is detected (PCI)
ReconnectController(0,0,0) : Status = Success

Shell> map
Device mapping table
fs0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
fs1 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11
D9-8002-D6217B60E588)
fs2 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11
DD-8000-D6217B60E588)
fs3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11
DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)
blk1 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
blk2 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry1)
blk3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)
blk4 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11
D9-8002-D6217B60E588)
blk5 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part2,Sig69542DAE-121A-11
D9-8003-D6217B60E588)
blk6 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part3,Sig69542DCC-121A-11
D9-8004-D6217B60E588)
blk7 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)
blk8 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig28E08EF2-F046-11
DD-8000-D6217B60E588)
blk9 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part2,Sig28E08F38-F046-11
DD-8000-D6217B60E588)
blkA : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig28E08F4C-F046-11
DD-8000-D6217B60E588)

[sujit kumar singh]

Hi Joe,

Scsi(Pun6,Lun0) HP C5683A C908 ( 40 MBytes/sec) this is the Tape device --- this you can see when you go on to add a boot entry options in the EFI


fs1 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11
D9-8002-D6217B60E588) --- this is the first Hard Disk(as can see HD) and also Partition 1 (Part1 mentioned)
this looks to the booted OS as --- /dev/dsk/cxtydzs1
also it looks fs1 as this has a valid FS that id EFI partition on this as a result of the install of the OS that you have tried (mark pun0,lun0)


blk4 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun0,Lun0)/HD(Part1,Sig69542D9A-121A-11
D9-8002-D6217B60E588
this is the first Hard Disk(as can see HD) and also Partition 1 (Part1 mentioned) -- note pun0,lun0 -- this is the raw dev file as os will look this as /dev/rdsk/cxtydzs1 -- note Part1 --- means Partition1 that is EFI part

blk9 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part2,Sig28E08F38-F046-11
DD-8000-D6217B60E588
this is the second Hard Disk(as can see HD) and also Partition 1 (Part1 mentioned) -- note pun1,lun0 -- this is the raw dev file as os will look this as /dev/rdsk/cxtydzs1 -- note Part1 --- means Partition1 that is EFI part
but this partition doesnot ahcvw an EFI Filesys on this or you woulf have seen an FSD entry foe this also.



regards
sujit

[Joe Profaizer]

OK. I understand that, but I thought you wanted me to boot from the shell prompt itself by using and fs entry that cross-referenced a the dat tape drive.

[Joe Profaizer]

Question:
I know I can write an Ignite tape to my tape library via fibre channel connectivity. Can I restore the same tape from my tape library via fibre channel? I remember a few years back that I could not restore the ignite tape via fibre channel and was hoping the new rx4640 fw allows me to do so.

What I'm trying to do is take the current DAT drive out of the picture.

Thanks,

..Joe