HP UX11.11 cannot compile kernel

[LuisFSalas]

Hello.

I am trying to restore a broken server HP rp3440 and I have restored partially a back-up from a tape unit. Now I am trying to install all the kernel again but I have many problems. I have these situation:

# uname -a
HP-UX OMN01 B.11.11 U 9000/800 1146927145 unlimited-user license

# bdf
Filesystem kbytes used avail %used Mounted on
/dev/vg00/lvol3 10485760 3436998 6828812 33% /
/dev/vg00/lvol1 303125 107018 165794 39% /stand
/dev/vg00/lvol4 104857600 2632112 101426872 3% /opt

# ioscan -f
Class I H/W Path Driver S/W State H/W Type Description
=============================================================================
root 0 root CLAIMED BUS_NEXUS
ioa 0 0 sba CLAIMED BUS_NEXUS System Bus Adapter (880)
ba 0 0/0 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
usb 0 0/0/1/0 hcd CLAIMED INTERFACE NEC USB Interface
usbhub 0 0/0/1/0.1 hub CLAIMED DEVICE USB Root Hub
usb 1 0/0/1/1 hcd CLAIMED INTERFACE NEC USB Interface
usbhub 1 0/0/1/1.1 hub CLAIMED DEVICE USB Root Hub
usb 2 0/0/1/2 ehci CLAIMED INTERFACE NEC USB Interface
sideba 0 0/0/2/0 side_ba CLAIMED INTERFACE CMD IDE controller
ext_bus 0 0/0/2/0.0 side CLAIMED INTERFACE IDE Primary Channel
target 0 0/0/2/0.0.0 tgt CLAIMED DEVICE
disk 0 0/0/2/0.0.0.0 sdisk CLAIMED DEVICE TEAC DV-28E-C
target 1 0/0/2/0.0.7 tgt CLAIMED DEVICE
ctl 0 0/0/2/0.0.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 1 0/0/2/0.1 side CLAIMED INTERFACE IDE Secondary Channel
target 2 0/0/2/0.1.7 tgt CLAIMED DEVICE
ctl 1 0/0/2/0.1.7.0 sctl CLAIMED DEVICE Initiator
ba 1 0/1 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ext_bus 2 0/1/1/0 c8xx CLAIMED INTERFACE SCSI C1010 Ultra160 Wide LVD
target 3 0/1/1/0.0 tgt CLAIMED DEVICE
disk 1 0/1/1/0.0.0 sdisk CLAIMED DEVICE COMPAQ BD1468A4C5
target 4 0/1/1/0.7 tgt CLAIMED DEVICE
ctl 2 0/1/1/0.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 3 0/1/1/1 c8xx CLAIMED INTERFACE SCSI C1010 Ultra160 Wide LVD
target 5 0/1/1/1.7 tgt CLAIMED DEVICE
ctl 3 0/1/1/1.7.0 sctl CLAIMED DEVICE Initiator
lan 0 0/1/2/0 igelan CLAIMED INTERFACE HP PCI 1000Base-T Core
ba 2 0/2 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
lan 1 0/2/1/0 igelan CLAIMED INTERFACE HP A6825-60101 PCI 1000Base-T Adapter
ba 3 0/3 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ext_bus 4 0/3/1/0 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011
target 6 0/3/1/0.7 tgt CLAIMED DEVICE
ctl 4 0/3/1/0.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 5 0/3/1/1 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011
target 7 0/3/1/1.7 tgt CLAIMED DEVICE
ctl 5 0/3/1/1.7.0 sctl CLAIMED DEVICE Initiator
ba 4 0/4 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ba 5 0/6 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ba 6 0/7 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
tty 0 0/7/1/0 asio0 CLAIMED INTERFACE PCI SimpleComm (103c1290)
tty 1 0/7/1/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)
unknown -1 0/7/2/0 UNCLAIMED UNKNOWN PCI Display (10025159)
memory 0 8 memory CLAIMED MEMORY Memory
ipmi 0 16 ipmi CLAIMED INTERFACE IPMI Controller
processor 0 128 processor CLAIMED PROCESSOR Processor
processor 1 129 processor CLAIMED PROCESSOR Processor

and when I try to compile a have this:

# mk_kernel -s system
WARNING: No such device, tunable, or cdio ehci.
Ignoring the following line.
ehci
WARNING: No such device, tunable, or cdio side_ba.
Ignoring the following line.
side_ba
Generating module: krm...
Generating module: gvid_info...
Generating module: drmfgl...
Generating module: drmfglrx...
Generating module: gvid_him_cons...
Generating module: pfil...
Generating module: ipf...
Compiling conf.c...
(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1588: "GVID_NO_CLAIM_DEV" undefined.
(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1521: Incorrect initialization.
(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1521: Incorrect initialization.
(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 62: error 1521: Incorrect initialization.
(Bundled) cc: "/stand/build/space.h", line 19: error 1588: "vxdmp_tunables" undefined.
(Bundled) cc: "/stand/build/space.h", line 19: error 1521: Incorrect initialization.
(Bundled) cc: "/stand/build/space.h", line 19: error 1588: "vxvm_tunables" undefined.
(Bundled) cc: "/stand/build/space.h", line 19: error 1521: Incorrect initialization.
*** Error exit code 1

Stop.
config: make did an exit(1)
#

Please, may someone help me?. I am not able to install o compile any pack because compilation fails, even using sam.

Thank you so much in advance.

[Steven Schweda]

   I might have built a kernel once in my life, long ago, but perhaps
not, so I know nothing. But...

> (Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1588: "GVID_NO_CLAIM_DEV" undefined.

   Apparently, if you're using "/usr/conf/space.h.d/gvid_space.h", then
GVID_NO_CLAIM_DEV should be defined.  My guess (but what do I know?) is
that that C macro gets defined (somehow) from the value of the kernel
tunable "gvid_no_claim_dev".  Around here ("hp workstation c7000"):

dy# uname -a
HP-UX dy B.11.11 U 9000/785 2012616114 unlimited-user license

and SAM > Kernel Configuration > Configurable Parameters says that
"gvid_no_claim_dev" is defined (Current Value = Pending Value = 0), and
it's Static.

   A quick Web search suggests that it's a PCI Device-ID+Vendor-ID for a
graphics card which you want to be ignored.  If you don't have that
parameter defined, then I might try to find away to add it.

   "/usr/conf/master.d/gvid" seems to be related.

   My "/stand/build/space.h" is mostly a bunch of "#include" directives
(including "#include "/usr/conf/space.h.d/gvid_space.h"), and an array
declaration which includes the items "vxdmp_tunables" and
"vxvm_tunables".  Presumably, those should be defined someplace, too.
Perhaps:
      /usr/conf/space.h.d/vxdmp_space.h
      /usr/conf/space.h.d/vxvm_space.h

   I certainly don't know enough about how UP-UX builds its kernel, but
perhaps one of us (you) can do more reading, and find out how that C
macro is supposed to get defined.  My guess is that you have some
corrupt files.

[LuisFSalas]

Dear Steven, how are you?.

Thank you so much for your time and suggestion.

I need to compile the Kernel because I am trying to restore a back-up from a tape. The problem is that the process is incomplete, so I have to ignore errors and continue. Finally I have the UX 11.11 able to boot from hard disk but many process don't work because there are not full files in theirs folders.

I try to reinstall again all the filesets, and is that moment when kernel has to be complied.

Yesterday night I were investigating a little bit more and I discovered that some "*.h" files copied from the CD-rom are corrupted, and when compiler try to use it, compilations fails.

Now I am going to restore again the tape back-up and I will go to the origin. I will take a copy of the *.h files before to install any fileset. I don't know the reason, but some of these files are corrupted from CD-rom....

I will post more news if I can get more info.

Thank you so much in advance.

Luis.

[georgek_1]

Hello LuisFSalas,

The basic issue seems to be incomplete restoration from tape , resulted in missing files .

You may see if you have another good backup , try restore the OS from the same .

I work for HPE/ I am an HPE Employee (HPE Community)

[LuisFSalas]

Hello  georgek_1,

Thank you so much for your reply. It's true, the backup from tape tails and the restored O.S. is not complete. I am trying to re-install all the lost packages but my problem is that installation fails.

I have discovered that the problem is that all the *.h files from CD-rom of HP UX11.11 are codified and I cannot access to the correct *.h files. This is the reason why I cannot compile the kernel during installation, because *.h files cannot be accessed correctly.

I suppose that it is due to license and/or user code from the CD-rom that I am using.

Have anybody some CD-ROM 'iso" with the correct files? or some valid user to access to the CD-rom?.

Thank you so much in advance.

L.

[Steven Schweda]

> I have discovered that the problem is [...]

   Your analysis is interesting, but it might be more helpful if you
revealed what you did, and what happened when you did it, rather than
what you think it all means.

> [...] all the *.h files from CD-rom of HP UX11.11 are codified and I
> cannot access to the correct *.h files. [...]

   "cannot" is not a useful problem description.  It does not say what
you did.  It does not say what happened when you did it.  As usual,
showing actual actions (commands) with their actual results (error
messages, ...) can be more helpful than vague descriptions or
interpretations.  Copy+paste is your friend.

> I suppose that it is due to license and/or user code from the CD-rom
> that I am using.

   I can't see the label on your (unspecified) "the CD-rom".  I've
installed HP-UX from CD-ROMs on a few systems (long ago), and I don't
recall needing any codeword for the base OS.

   If I had a problem with the HP-UX files on a backup tape (of some
unspecified type or other), then I might try to install HP-UX from the
CD-ROM(s), perhaps onto a different disk.

[LuisFSalas]

Hello Steven, how are you?.

Thank you so much for your reply and interest in this problem.

I apologice too much that my information was not so specific. I am going to collect more technical and specific info and I will post here again. Anyway, as I have wroten in other post, I replaced a lot of hardware of this server because they were broken, so I have new motherboard, new RAM, new hard disk and new SCSI controller. My back-up tape has errors and during the process I had to choose between 1) stop process 2) continue ignoring errors 3) go to shell.

I choosed 2) option and after to finish the process I got this:

Firmware Version  46.34

Duplex Console IO Dependent Code (IODC) revision 1

Firmware Version  46.34

Duplex Console IO Dependent Code (IODC) revision 1

------------------------------------------------------------------------------

   (c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved

------------------------------------------------------------------------------

  Processor   Speed            State           CoProcessor State  Cache Size

  Number                                       State              Inst    Data

  ---------  --------   ---------------------  -----------------  ------------

      0     1000  MHz   Active                 Functional         67108864 67108864

      1     1000  MHz   Idle                   Functional         67108864 67108864

  Central Bus Speed (in MHz)  :        200

  Available Memory            :    4194304  KB

  Good Memory Required        : Not initialized. Defaults to 32 MB.

   Primary boot path:    0/1/1/0.0

   Alternate boot path:  0/0/2/0.3

   Console path:         0/7/1/1.0

   Keyboard path:        0/0/4/0.0

Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.

Proceeding...

Trying Primary Boot Path

------------------------

Booting...

Boot IO Dependent Code (IODC) revision 1

HARD Booted.

ISL Revision A.00.43  Apr 12, 2000

ISL booting  hpux

Boot

: disk(0/1/1/0.0.0.0.0.0.0;0)/stand/vmunix

10944512 + 2215936 + 22823144 start 0x1fafe8

alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.

gate64: sysvec_vaddr = 0xc0002000 for 2 pages

NOTICE: nfs3_link(): File system was registered at index 3.

NOTICE: autofs_link(): File system was registered at index 6.

NOTICE: cachefs_link(): File system was registered at index 7.

[Osxinit]: Allocated ots_timeout_lock [40220ac0]

probe: port 3 overcurrent 0x0

probe: port 1 overcurrent 0x0

probe: port 2 overcurrent 0x0

igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0

igelan1: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/2/1/0

    System Console is on the Built-In Serial Interface

Entering cifs_init...

Initialization finished successfully... slot is 9

Logical volume 64, 0x3 configured as ROOT

Logical volume 64, 0x2 configured as SWAP

Logical volume 64, 0x2 configured as DUMP

    Swap device table:  (start & size given in 512-byte blocks)

        entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216

Warning: time-of-day register time is out-of-range

Getting time from file system

Starting the STREAMS daemons-phase 1

Checking root file system.

file system is clean - log replay is not required

Root check done.

Warning: time-of-day register time is out-of-range

Getting time from file system

Create STCP device files

Starting the STREAMS daemons-phase 2

             $Revision: vmunix:    vw: -proj    selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'  Wed Nov  8 19:24:56 PST 2000 $

Memory Information:

    physical page size = 4096 bytes, logical page size = 4096 bytes

    Physical: 4192256 Kbytes, lockable: 3112640 Kbytes, available: 3586204 Kbytes

/sbin/ioinitrc:

insf: Installing special files for ipmi instance 0 address 16

insf: Installing special files for pseudo driver framebuf

/sbin/krs_sysinit:

/sbin/bcheckrc:

Checking for LVM volume groups and Activating (if any exist)

Volume group "/dev/vg00" has been successfully changed.

vxfs fsck: sanity check: root file system OK (mounted read/write)

Checking hfs file systems

/sbin/fsclean: /dev/vg00/lvol1 (mounted) ok

HFS file systems are OK, not running fsck

Checking vxfs file systems

/dev/vg00/lvol3 :

vxfs fsck: sanity check: root file system OK (mounted read/write)

/dev/vg00/lvol4 :

vxfs fsck: sanity check: /dev/vg00/lvol4 OK

Cleaning /etc/ptmp...

(c)Copyright 1983-2000 Hewlett-Packard Co.,  All Rights Reserved.

(c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California

(c)Copyright 1980, 1984, 1986 Novell, Inc.

(c)Copyright 1986-1992 Sun Microsystems, Inc.

(c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology

(c)Copyright 1989-1993  The Open Software Foundation, Inc.

(c)Copyright 1986 Digital Equipment Corp.

(c)Copyright 1990 Motorola, Inc.

(c)Copyright 1990, 1991, 1992 Cornell University

(c)Copyright 1989-1991 The University of Maryland

(c)Copyright 1988 Carnegie Mellon University

(c)Copyright 1991-2000 Mentat Inc.

(c)Copyright 1996 Morning Star Technologies, Inc.

(c)Copyright 1996 Progressive Systems, Inc.

(c)Copyright 1991-2000 Isogon Corporation, All Rights Reserved.

                           RESTRICTED RIGHTS LEGEND

Use, duplication, or disclosure by the U.S. Government is subject to

restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in

Technical Data and Computer Software clause in DFARS 252.227-7013.

                           Hewlett-Packard Company

                           3000 Hanover Street

                           Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set

forth in FAR 52.227-19(c)(1,2).

Open Source Software has been installed on this system.  See

/opt/OpenSource/etc/copyright

/sbin/auto_parms: DHCP access is disabled (see /etc/auto_parms.log)

cat: Cannot open /usr/local/graphon/etc/gold.conf: No such file or directory

     HP-UX Start-up in progress

     __________________________

     Configure system crash dumps ............................................. OK

     Removing old vxvm files .................................................. OK

     Mount file systems ....................................................... OK

     Update kernel and loadable modules ....................................... N/A

     Initialize loadable modules .............................................. NOTICE: modld: Module already loaded

OK

     Setting hostname ......................................................... OK

     Start Kernel Logging facility ............................................ N/A

     Set privilege group ...................................................... N/A

     Display date ............................................................. N/A

     Copy processor logs to /var/tombstones ................................... OK

     Save system crash dump if needed ......................................... N/A

     Start evp ................................................................ OK

     Enable auxiliary swap space .............................................. OK

     Start syncer daemon ...................................................... OK

     Configure Loopback interfaces (lo0) ...................................... OK

     Configure EARLY NDD tunables ............................................. OK

     Configuring all unconfigured software filesets ........................... OK

     Configuring PFIL ......................................................... OK

     Starting IPFilter ........................................................ NOTICE: modld: Module already loaded

OK

     Recover editor crash files ............................................... OK

     Clean UUCP ............................................................... OK

     List and/or clear temporary files ........................................ OK

     Clean up old log files ................................................... OK

     Start system message logging daemon ...................................... OK

     Start pty allocator daemon ............................................... OK

     Configuring OLA/R interface .............................................. N/A

     Start network tracing and logging daemon ................................. OK

     Configure HP igelan Gigabit Ethernet interfaces .......................... OK

     Configure HP iether Gigabit Ethernet interfaces .......................... OK

     Configure HP Gigabit Ethernet interfaces ................................. OK

     Configure HP Ethernet interfaces ......................................... OK

     Create PCI FDDI device files. ............................................ OK

     Configure HP 100BASE-T interfaces ........................................ N/A

     Configure VLAN interfaces ................................................ OK

     Configure LAN interfaces ................................................. OK

     Start name server daemon ................................................. N/A

     Start OTS ................................................................ FAIL *

     Starting HP-UX Secure Shell .............................................. FAIL *

     Start NFS core subsystem ................................................. OK

     Start NIS+ server subsystem .............................................. OK

     Start NIS+ client subsystem .............................................. OK

     Start NIS server subsystem ............................................... OK

     Start NIS client subsystem ............................................... OK

     Start NFS client subsystem ............................................... OK

     Start the Trusted Mode with NIS+ subsystem ............................... N/A

     Configure pseudo devices for MAC/LLA access .............................. OK

     Start multicast routing daemon ........................................... N/A

     Start Internet services daemon ........................................... OK

     Start dynamic routing daemon ............................................. N/A

     Start router discover protocol daemon .................................... N/A

     Configuring PPP Interface ................................................ OK

     Start RARP protocol daemon ............................................... N/A

     Start remote system status daemon ........................................ N/A

     Configuring man pages for Internet Services .............................. OK

     Starting mail daemon ..................................................... N/A

     Starting outbound connection daemons for DDFA software ................... N/A

     Start SNMP Master Network Management daemon .............................. N/A

     Start OSPF MIB Network Management subAgent ............................... N/A

     Start SNMP HP-UNIX Network Management subAgent ........................... N/A

     Start SNMP MIB-2 Network Management subAgent ............................. N/A

     Start SNMP Trap Dest Network Management subAgent ......................... N/A

     Start DCE daemons ........................................................ N/A

     Start SNMP PCI FDDI Network Management subAgent .......................... OK

     Start RPC daemon if needed ............................................... N/A

     Start CIM cimserver subsystem ............................................ N/A

     Start Isogon License Server Daemon ....................................... N/A

     Initialize Instant Capacity .............................................. OK

     Start remote boot daemon ................................................. N/A

     Starting X Font Server at TCP port 7000 .................................. N/A

     Start vt daemon .......................................................... N/A

     Starting UDC server ...................................................... N/A

     Start time synchronization ............................................... N/A

     Start accounting ......................................................... N/A

     Install/Load XF86 DLKM Helper Modules .................................... OK

     Starting the password/group assist subsystem ............................. OK

     Starting HP Disk Array Manager daemons. .................................. OK

     Starting disk array monitor daemons. ..................................... OK

     Start print spooler ...................................................... N/A

     Starting HP Distributed Print Service .................................... OK

     Start clock daemon ....................................................... OK

     Start diagnostic subsystem ............................................... cron aborted: can't change directory to the crontab directory.

OK

     Start auditing subsystem ................................................. N/A

     Start audio server daemon ................................................ N/A

     Start Distributed Single Logical Screen daemon ........................... N/A

     Start USB hub daemon ..................................................... OK

     SAM System administration configuration .................................. OK

     OVPA performance software is being started. .............................. N/A

     Initialize the fax devicefile ............................................ OK

     Starting ObAM Application Server ......................................... N/A

     Initialize Software Distributor agent daemon ............................. OK

     Starting CIFS Client ..................................................... N/A

     Configure HP RAID SA interfaces .......................................... N/A

     Starting Event Monitoring Service ........................................ OK

     Start EMS SNMP subagent .................................................. OK

     Configure HP Fibre Channel Mass Storage interfaces ....................... OK

     Configure HP Internal RAID interfaces .................................... N/A

     Configure for Java ....................................................... OK

     Configuring Ultra320 SCSI Mass Storage interfaces ........................ OK

     Configure HP Fibre Channel Tachyon TL/TS Mass Storage interfaces ......... OK

     Configuring HP Fibre Channel FCD Mass Storage interfaces ................. OK

     Start NFS server subsystem ............................................... OK

     Start X print server(s) .................................................. N/A

     Starting the GraphOn Login Daemon ........................................ N/A

     Starting the System Management HomePage server ........................... OK

     Starting the NSUE (Marconi Communications Software Systems) subsystem .... nohup: /usr/nsue/bin/RunNSUE: No such file or directory

OK

     Starting OVTrcSrv... ..................................................... FAIL *

     Starting OVCtrl... ....................................................... OK

     Start CDE login server ................................................... OK

     Starting PRNGD (Pseudo Random Number Generator Daemon) ................... N/A

     * - An error has occurred !

     * - Refer to the file /etc/rc.log for more information.

The system is ready.

INIT: Command is respawning too rapidly.

Will try again in 5 minutes.

Check for possible errors.

id:cim1 "/opt/wbem/lbin/cimserverd"

GenericSysName [HP Release B.11.11] (see /etc/issue)

Console Login: root

Password:

Please wait...checking for disk quotas

(c)Copyright 1983-2000 Hewlett-Packard Co.,  All Rights Reserved.

(c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California

(c)Copyright 1980, 1984, 1986 Novell, Inc.

(c)Copyright 1986-1992 Sun Microsystems, Inc.

(c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology

(c)Copyright 1989-1993  The Open Software Foundation, Inc.

(c)Copyright 1986 Digital Equipment Corp.

(c)Copyright 1990 Motorola, Inc.

(c)Copyright 1990, 1991, 1992 Cornell University

(c)Copyright 1989-1991 The University of Maryland

(c)Copyright 1988 Carnegie Mellon University

(c)Copyright 1991-2000 Mentat Inc.

(c)Copyright 1996 Morning Star Technologies, Inc.

(c)Copyright 1996 Progressive Systems, Inc.

(c)Copyright 1991-2000 Isogon Corporation, All Rights Reserved.

                           RESTRICTED RIGHTS LEGEND

Use, duplication, or disclosure by the U.S. Government is subject to

restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in

Technical Data and Computer Software clause in DFARS 252.227-7013.

                           Hewlett-Packard Company

                           3000 Hanover Street

                           Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set

forth in FAR 52.227-19(c)(1,2).

Open Source Software has been installed on this system.  See

/opt/OpenSource/etc/copyright

Cannot chdir to /var/news

Value of TERM has been set to "vt100".

WARNING:  YOU ARE SUPERUSER !!

Then I tryed to re-install several filests because due to the erros from my backup tape there are a lot of loosed files, so I used this command:

I have to say that I made a copy of the four (4) CD-ROM in the hard disk, at folder /var/spool/sw. I did it using the #sam and during this process I got the message saing that I need a user code in order to access to the full contents of CD-ROM (I have not the exactly message here a this moment, but I will post in a few days).

# swinstall -x reinstall=true -x autoreboot=true -x patch_match_target=true -s /var/spool/sw

=======  08/11/22 11:09:56 BST  BEGIN swinstall SESSION

         (non-interactive) (jobid=OMN01-0031)

       * Session started for user "root@OMN01".

       * Beginning Selection

       * Target connection succeeded for "OMN01:/".

       * Source connection succeeded for "OMN01:/var/spool/sw".

NOTE:    The software specified contains a kernel fileset or a

         dynamic_module fileset.  The kernel will be modified, and if

         necessary the system will be rebooted.

       * Source:                 /var/spool/sw

       * Targets:                OMN01:/

       * Software selections:

           + BUNDLE11i,r=B.11.11.0306.1,a=HP-UX_B.11.11_32/64,v=HP

           + FEATURE11-11,r=B.11.11.0209.5,a=HP-UX_B.11.11_32/64,v=HP

           + HWEnable11i,r=B.11.11.0509.430,a=HP-UX_B.11.11_32/64,v=HP

…

…

…

WARNING: "OMN01:/":  90 filesets had warnings.

ERROR:   "OMN01:/":  The kernel build script failed.

       * The execution phase failed for "OMN01:/".

       * Analysis and Execution had errors.

ERROR:   More information may be found in the agent logfile using the

         command "swjob -a log OMN01-0031 @ OMN01:/".

=======  08/11/22 11:10:55 BST  END swinstall SESSION (non-interactive)

         (jobid=OMN01-0031)

# swjob -a log OMN01-0031 @ OMN01:/

=======  08/11/22 11:09:56 BST  BEGIN install AGENT SESSION (pid=5156)

         (jobid=OMN01-0031)

       * Agent session started for user "root@OMN01". (pid=5156)

       * Beginning Analysis Phase.

       * Source:           OMN01:/var/spool/sw

       * Target:           OMN01:/

       * Target logfile:   OMN01:/var/adm/sw/swagent.log

       * Reading source for product information.

…

…

…

NOTE:    Building a new kernel based on template file "/stand/system"

WARNING: No such device, tunable, or cdio ehci.

        Ignoring the following line.

        ehci

WARNING: No such device, tunable, or cdio side_ba.

        Ignoring the following line.

        side_ba

Generating module: krm...

Generating module: gvid_info...

Generating module: drmfgl...

Generating module: drmfglrx...

Generating module: gvid_him_cons...

Generating module: pfil...

Generating module: ipf...

Compiling /stand/build/conf.c...

(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1588: "GVID_NO_CLAIM_DEV" undefined.

(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1521: Incorrect initialization.

(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 48: error 1521: Incorrect initialization.

(Bundled) cc: "/usr/conf/space.h.d/gvid_space.h", line 62: error 1521: Incorrect initialization.

(Bundled) cc: "/stand/build/space.h", line 19: error 1588: "vxdmp_tunables" undefined.

(Bundled) cc: "/stand/build/space.h", line 19: error 1521: Incorrect initialization.

(Bundled) cc: "/stand/build/space.h", line 19: error 1588: "vxvm_tunables" undefined.

(Bundled) cc: "/stand/build/space.h", line 19: error 1521: Incorrect initialization.

*** Error exit code 1

Stop.

         make failure.

ERROR:   The command "/usr/sbin/mk_kernel", which is used to rebuild

         the kernel, has failed.  Because kernel-related filesets were

         installed, this command must be executed by "swinstall",

         without failures, before the load can continue.  Check the

         above output for details about the failure.

NOTE:    The Install Phase has suspended.  Check the above output for

         reasons.

=======  08/11/22 11:10:55 BST  END install AGENT SESSION (Aborted)

If you edit the file "/usr/conf/space.h.d/gvid_space.h", you can see that file is not text file. Instead of this, it look a binary file with non understanding characters. This is the real problem, compiler can not compile it because there is nothing like code lines in these files during compilation.

I have tryed to edit several *.h files from CD-ROM but all the *.h files look to be "codified" or corrupted. Perhaps I need some user code to access to these files.

I will post the message that I have when I try to access to these CD-ROM.

Thank you again.

Luis.

[Steven Schweda]

>    If I had a problem with the HP-UX files on a backup tape (of some
> unspecified type or other), then I might try to install HP-UX from the
> CD-ROM(s), perhaps onto a different disk.

   That's still my advice.  Whatever you've done up to now, the compiler
is complaining about various header files under "/usr/conf/" and
"/stand/build/".  I'd expect a new installation of HP-UX onto a virgin
disk to give you good versions of such files.

   If you can install HP-UX onto a virgin disk, then you can decide
whether you want to copy files from that new disk onto your old/corrupt
disk, or try to configure the new/working disk with all the other
software from your old/corrupt disk.

> [...] I am trying to re-install all the lost packages [...]

   I don't know how to do that.  I believe that I know how to install
HP-UX on a virgin disk, and I'd expect that to extract and install all
the necessary files from the HP-UX installation CD-ROMs.

[LuisFSalas]

Dear Steven,

Thank you so much once again for your interest and collaboration. I am back again into this task and now I can access to the server again.

The problem that I have is that all my CD-ROM have been downloaded from internet, so they are not bootable. This is the reason why I cannot do a new clean installation.

Using the tape I could generate a new HD bootable with HP UX 11.11 but with many files lost. It is possible to reinstall again all the filesets you need with the command:

#swinstall -s /cdrom

When I do it, I have this screen:

┌ === SD Install - Software Selection (OMN01) (1) ┐
│File View Options Actions Help │
│ │ Change Options ... │L-K for keyboard help. │
│Source: OM│ ────────────────── │ │
│Target: O│ Refresh List │ │
│ └────────────────────┘ │
│Only software compatible with the target is available for selection. │
│──────────────────────────────────────────────────────────────────────────────│
│Top (Bundles and Products) 0 of 19 selected│
│──────────────────────────────────────────────────────────────────────────────│
│ Marked? Name Revision Information │
│┌───────────────────────────────────────────────────────────────────────────┐ │
││ B9901AA -> A.03.05.05 HP IPFilter 3.5alpha5 ^ │
││ Base-VXVM -> B.03.50.5 Base VERITAS Volume Mana │
││ CDE-ChineseS -> B.11.11 Simplified Chinese CDE E │
││ CDE-ChineseT -> B.11.11 Traditional Chinese CDE │
││ CDE-English -> B.11.11 English CDE Environment │
││ CDE-French -> B.11.11 French CDE Environment │
││ CDE-German -> B.11.11 German CDE Environment │
││ CDE-Italian -> B.11.11 Italian CDE Environment │
││ CDE-Japanese -> B.11.11 Japanese CDE Environment v │
│└< >┘ │
│ │
└──────────────────────────────────────────────────────────────────────────────┘

If you go to Menu Option -> Change option yo must select these others configurations:

┌ === SD Install - Software Selection (OMN01) (1) ┐
│File View ┌ Options (OMN01) ┐ Help │
│ │ │ │
│Source: OM│ [X] Create target path if not there already │ │
│Target: O│ [X] Mount filesystems in /etc/fstab or /etc/checklist │ │
│ │ [X] Reinstall filesets even if same revision exists │ │
│Only softw│ [X] Reinstall files even if same one already there │. │
│──────────│ [X] Use checksum when checking if file is the same │───────────│
│Top (Bundl│ [ ] Compress files during transfer │19 selected│
│──────────│ [ ] Allow creation of multiple versions │───────────│
│ Marked? │ [ ] Defer configuration │ │
│┌─────────│ [ ] Enable auto-recovery of product for load errors │─────────┐ │
││ │ [ ] All targets to resolve the source locally │lpha5 ^ │
││ │ [ ] Allow installation of lower version than current │ume Mana │
││ │ [ ] Allow installation of incompatible software │se CDE E │
││ │ [ ] Autoselect dependencies when marking software │ese CDE │
││ │ [ ] Enforce dependency analysis errors in agent │ronment │
││ │ [X] Enforce script failures │onment │
││ │ [X] Enforce disk space analysis errors │onment │
││ │ [X] Save files replaced by patch for later rollback │ronment │
││ │───────────────────────────────────────────────────────│ironment v │
│└< │ [ OK ] [ Cancel ] [ Help ] │ >┘ │
│ └───────────────────────────────────────────────────────┘ │
└──────────────────────────────────────────────────────────────────────────────┘

Now you must selext the menu View -> Change software view -> Start with products

Then main problem that I have is to access to all the "*.h" files inside of cd-rom. For instance, if I try to do #cat xsub.h inside of cd-rom I have this:

# cat ./netscapedirsvr6/nds-nsperl/var/opt/netscape/servers/lib/nsperl5.005_03/lib/pa-risc2.0-thread/core/xsub.h
C▒=▒Xks▒F▒~ō▒0▒J▒▒f▒ۑe▒▒V@#▒"O▒a▒▒▒"▒4▒ｻ+KG▒$x▒9g▒޽{X▒h▒▒A▒i)▒▒▒▒▒p▒G{▒▒▒▒▒▒X▒▒▒▒(▒
Ӊn▒▒eXws▒▒k▒▒m\▒M▒▒▒Nre*▒y▒$▒}T▒▒▒▒
▒▒▒)▒矁▒1▒c▒|▒,n▒|▒▒▒)▒▒▒!r▒G▒m▒$X▒▒▒
^▒#0OFуVJ▒▒▒ʼ▒▒'▒▒^▒▒$▒D
▒▒▒▒▒␤▒─▒£")▒H▒▒'▒≠▒▒,▒▒─▒▒▒▒└▒"▒≥*▒▒[a▒#�▒۳Ьۅ▒z[▒▒1▒▒mZ▒▒▒톥z▒q▒▒;▒?<▒▒[�ײ▒▒▒R▒Ƶ5▒r0x33▒▒▒æq▒$▒"▒t[@▒}▒(▒
▒▒)+▒▒%.▒└▒A▒▒▒6▒1▒▒P▒▒▒▒O▒ͽ
▒▒▒▒▒▒▒│V└▒▒>▒I(▒▒▒
▒┴▒▒≤▒▒▒➤▒▒▒▒H▒=R▒˥▒=R▒▒▒8<▒.▒P▒H▒▒▒q▒▒b;%▒▒;H▒~XJ▒0▒▒▒>▒▒ɾT▒▒ݺ2▒,)▒Qת▒┼▒▒]▒π▒▒➤.G▒!│▒▒▒!▒▒▒Lπ▒-L▒K4▒:▒┘̾0
┐▒6▒▒ ➤▒✔.▒TD␋^▒▒▒␋:ĶS▒▒▒>8▒▒▒Y߆▒▒▒(J6[▒⎽0K┌
┌▒▒"▒▒▒£▒
▒▒~▒D▒▒▒⎼▒ȷ␋▒6N▒$)▒"⎽R⎻▒π4ʥ≤▒┌▒▒E▒ ±B D┤▒▒W▒▒ ړ▒ˏ▒▒N┤Z▒J+▒£▒│ ?▒"✘▒:?;π▒U▒Q9?l▒æ▒C,▒▒dfj4▒▒0]▒+▒▒▒+▒2K▒Fa?▒▒U I/▒▒▒▒~▒▒=kU▒&▒'▒eL▒▒M
k▒kJ▒
▒▒▒t▒▒I▒|▒8▒41H֟<▒▒w
G6 ▒]▒▒)▒▒=TY▒P▒▒▒~j]▒▒?`▒▒▒`▒▒f?52<;▒!▒4▒ǚ^I▒
▒▒▒!▒▒u,x=Vז▒J׺~N'▒▒▒mgi]P▒$▒{e▒▒▒N̟⎻▒"▒X
▒─▒
▒▒OcN܋S ▒E▒^▒]▒▒I▒~ $Ѐ▒;E▒6▒▒▒▒0▒▒▒q\▒▒Mi▒p▒▒)▒b!▒▒:▒▒0Y
▒4▒AG▒▒H▒▒▒▒\▒g▒▒⎻▒▒▒Y▒▒▒5%─␌▒P▒Q≥▒▒▒ݮHĹ▒│▒⎺Ժ▒G▒▒┬▒▒▒▒▒▒▒▒▒▒┤8▒┬▒£I▒➤
┼*▒▒°ό▒✔▒▒O▒▒┌➤␋4▒▒▒&▒▒▒▒"▒•␌▒▒▒T▒▒▒▒63&▒]E'⎼▒▒▒▒│├✘⎼└-256␌⎺┌⎺⎼▒➤▒▒▒⎼▒£▒▒3H▒?ʕ▒▒:➤▒▒?
=P▒┌▒▒▒┘▒H▒▒\▒▒5▒N▒✘⎼˾▒▒%W▒▒W5B4O▒P⎼˔Ğ$▒6▒▒B⎼␌<=▒#7V▒▒4⎼␌.£▒"▒▒D▒&⎼✘ B▒▒+▒9▒▒3 ▒G▒;[▒▒\▒▒▒▒w▒▒▒a▒ɳ.▒▒:▒r▒d~▒<▒G▒}▒▒W▒▒7pA▒xterm-256color▒ۍC▒▒ߑ?
)▒~▒ݰW&▒▒Ƭ▒▒▒w▒-▒▒
▒q▒▒▒@▒▒▒X#▒▒R:7▒Z▒ޥ▒P▒▒▒OB▒V▒TQ8▒N▒# xterm-256colorxterm-256colorxterm-256color

If I do the same in any other "*.h" inside of the HD, I have text, for instance:

# cat /usr/conf/space.h.d/core-hpux.h
/* @(#) core-hpux.h $Date: 2004/02/04 17:28:52 $Revision: r11.11/1 PATCH_11.11 (PHKL_30307) */
/*
* BEGIN_DESC
*
* File:
* common/space_LP64/core-hpux.h $Revision: $
*
* Purpose:
* Definitions for core system configurable parameters.
*
* Classification: Release to Release Consistency Req:
* kernel private none
*
* BE header: no
*
* Shipped: yes
* /usr/conf/space.h.d/core-hpux.h
*
* NOTE:
* This header file contains information specific to the internals
* of the HP-UX implementation. The contents of this header file
* are subject to change without notice. Such changes may affect
* source code, object code, or binary compatibility between
* releases of HP-UX. Code which uses the symbols contained within
* this header file is inherently non-portable (even between HP-UX
* implementations).
*
* END_DESC
*/

#ifndef _MACHINE_SPACE_INCLUDED /* allows multiple inclusion */
#define _MACHINE_SPACE_INCLUDED

...

...

...

This is the reason why I cannot re-install O.S. I cannot access to the "*.h" files inside of CD-rom.

The CD-ROM label has this text: "software on this disk is secured and requires a codeword".

I am afraid that I have to introduce some "codeword" in order to access to full information.

Does someone know a valid codeword for these CD-rom's?.

Thank you so much in advance.

Luis.

[Steven Schweda]

> The problem that I have is that all my CD-ROM have been downloaded
> from internet, so they are not bootable. [...]

   I doubt it.

   First, "internet" is a very big place.  What, more precisely, did you
download, and what are you doing with whatever you downloaded?  If you
got CD-ROM images (often referred to as ".iso" files), did you make
actual CD-R discs from them?  I don't see why "downloaded from internet"
would imply "not bootable".

> This is the reason why I cannot re-install O.S. I cannot access to the
> "*.h" files inside of CD-rom.

   What you've been doing might not work, but I'd still expect a normal
installation to work.  It always did for me.  I'd expect the HP-UX
installer to be able to extract what it needs from the installation
CD-ROMs, even if you can't.

> The CD-ROM label has this text: "software on this disk is secured and
> requires a codeword".

   I'm sure that that's true for some of the software (like, say,
compilers); I'm less sure that it's true for the base OS.  As I said,
I don't recall needing any codeword to install the base OS.

> Does someone know a valid codeword for these CD-rom's?.

   With my weak psychic powers, I know nothing about your (unspecified)
"these CD-rom's".  Also, as I understand it, the codewords were
product-specific.  (And I don't recall needing any codeword to install
the base OS.)

[LuisFSalas]

Hello Steven again, and thank you for your reply.

I downloaded CD-ROMS from here:

https://archive.org/details/hp-ux11i11.0

You can see labels and also the contents. They are "ISO" files and I used Alcohol software do CD-ROMs.

I am trying to install from them, but I have error messages because CD-ROM is not bootable. Perhaps I made a bad copy from ISO?... This is the message with CD-ROM inserted and I try to boot from CD.:

---- Main Menu ---------------------------------------------------------------

Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices

COnfiguration menu Displays or sets boot values
INformation menu Displays hardware information
SERvice menu Displays service commands

DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
----
Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1
P1 0/1/1/0.0 intscsia.0 Random access media 1
P2 0/3/1/0.3 Sequential access media 3

Main Menu: Enter command or menu > bo p0
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1

IPL error: bad LIF magic.
.... FAILED.

I am going to try a new installation, but at this moment I am not able to boot from CD-ROM....

Thank you again.

Luis.

[Patrick Wallek]

Putting the legality of those images on that site aside, none of the ISO Images you downloaded are bootable disks.  Those are all just applications or add-on software.

The HP-UX Installation disks are what you would need in order to boot and install the OS.

[LuisFSalas]

Thank you so much Patrick for your reply.

I suspect that, and I am downloading other CD's from here:

https://fsck.technology/software/HP/HP-UX%20Install%20Media/

Anyway, I am still not sure that ISO's can be bootable.

Let's see.....

Thank you again.

Luis.

[Patrick Wallek]

An ISO image can create a bootable DVD.  That is how HPE distributes HP-UX now.

[LuisFSalas]

Hi Patrick again.

Please, may you explain me if I can do this DVD with the ISO's that I hace downloaded?. If not, Is there any way to download that ISO?. 

Thank you so much again.

Luis.

[LuisFSalas]

I have tryed to restore again ther server from my tape and this is the process. Here you can see my failures....

Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1
P1 0/1/1/0.0 intscsia.0 Random access media 1
P2 0/3/1/0.3 Sequential access media 3

Main Menu: Enter command or menu > bo p2
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 3

HARD Booted.

ISL Revision A.00.44 Mar 12, 2003

ISL booting hpux (;0):INSTALL

Boot
: tape(0/3/1/0.3.0.0.0.0.0;0):WINSTALL
12296192 + 2257008 + 2718888 start 0x20c568

alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3e900000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0
igelan1: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/2/1/0

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 4192256 Kbytes, lockable: 3192984 Kbytes, available: 3684920 Kbytes

* Preparing to execute init...
======= 08/31/20 10:06:51 EDT HP-UX Installation Initialization.
@(#)Ignite-UX Revision C.7.9.260
@(#)ignite/launch (opt) Revision:
/branches/IUX_RA0909_WEB/ignite/src@78846 Last Modified: 2009-08-13
14:15:12 -0600 (Thu, 13 Aug 2009)
* Configuring RAM filesystems...
* Scanning system for IO devices...
* Boot device is: 0/3/1/0.3.0
Recovery tape created from system: OMN01 on Thu Oct 22 11:26:41 2009

WARNING: The configuration information calls for a non-interactive
installation.

Press <Return/Enter> within 10 seconds to cancel batch-mode installation:
* Using client directory: /var/opt/ignite/clients/0x0016357370D4
* Checking configuration for consistency...
WARNING: The disk at: 0/1/1/0.0.0 (SEAGATE_ST3146707LC) appears to contain a
file system and boot area. Continuing the installation will destroy
any existing data on this disk.

Press <Return/Enter> within 10 seconds to cancel batch-mode installation:
* Continuing despite above warnings.
* Attempting a non-interactive installation.
* Loading configuration utility...
* Beginning installation from source: /dev/rmt/c4t3d0BEST
======= 08/31/20 10:07:45 EDT Starting system configuration...
* Configure_Disks: Begin
* Mapping LUN Instance Data
* Will install B.11.11 onto this system.
* Using LVM for disk 0/1/1/0.0.0 (c2t0d0), group: vg00
* Creating LVM physical volume "/dev/rdsk/c2t0d0" (0/1/1/0.0.0).
* Creating volume group "vg00".
* Creating logical volume "vg00/lvol1" (/stand).
* Creating logical volume "vg00/lvol2" (swap_dump).
* Creating logical volume "vg00/lvol3" (/).
* Creating logical volume "vg00/lvol4" (/opt).
* Extending logical volume "vg00/lvol1" (/stand).
* Extending logical volume "vg00/lvol2" (swap_dump).
* Extending logical volume "vg00/lvol3" (/).
* Extending logical volume "vg00/lvol4" (/opt).
* Making HFS filesystem for "/stand", (/dev/vg00/rlvol1).
* Making VxFS filesystem for "/", (/dev/vg00/rlvol3).
* Making VxFS filesystem for "/opt", (/dev/vg00/rlvol4).
* Setting rotational delay to 0 for "/stand".
* Configure_Disks: Complete
* Download_mini-system: Begin
x ./sbin/fs/hfs/mkfs, 290816 bytes, 568 tape blocks
x ./sbin/fs/hfs/newfs, 212992 bytes, 416 tape blocks
x ./sbin/fs/vxfs/mkfs, 393216 bytes, 768 tape blocks
x ./sbin/fs/vxfs/newfs, 327680 bytes, 640 tape blocks
x ./sbin/mkfs symbolic link to /sbin/fs_wrapper
x ./sbin/newfs symbolic link to /sbin/fs_wrapper
x ./sbin/lib/mfsconfig.d/hfs, 978 bytes, 2 tape blocks
x ./sbin/lib/mfsconfig.d/vxfs, 966 bytes, 2 tape blocks
x ./sbin/fs_wrapper, 233472 bytes, 456 tape blocks
x ./sbin/sh, 401408 bytes, 784 tape blocks
x ./usr/sbin/tunefs, 20480 bytes, 40 tape blocks
x ./sbin/extendfs symbolic link to /sbin/fs_wrapper
x ./sbin/fs/vxfs/extendfs, 319488 bytes, 624 tape blocks
x ./sbin/fs/hfs/extendfs, 245760 bytes, 480 tape blocks
x ./sbin/lvchange, 831488 bytes, 1624 tape blocks
./sbin/lvcreate linked to ./sbin/lvchange
./sbin/lvdisplay linked to ./sbin/lvchange
./sbin/lvextend linked to ./sbin/lvchange
./sbin/lvlnboot linked to ./sbin/lvchange
./sbin/lvreduce linked to ./sbin/lvchange
./sbin/lvremove linked to ./sbin/lvchange
./sbin/lvrmboot linked to ./sbin/lvchange
./sbin/pvchange linked to ./sbin/lvchange
./sbin/pvcreate linked to ./sbin/lvchange
./sbin/pvdisplay linked to ./sbin/lvchange
./sbin/pvmove linked to ./sbin/lvchange
./sbin/vgcfgbackup linked to ./sbin/lvchange
./sbin/vgcfgrestore linked to ./sbin/lvchange
./sbin/vgchange linked to ./sbin/lvchange
./sbin/vgcreate linked to ./sbin/lvchange
./sbin/vgdisplay linked to ./sbin/lvchange
./sbin/vgexport linked to ./sbin/lvchange
./sbin/vgextend linked to ./sbin/lvchange
./sbin/vgimport linked to ./sbin/lvchange
./sbin/vgreduce linked to ./sbin/lvchange
./sbin/vgremove linked to ./sbin/lvchange
./sbin/vgscan linked to ./sbin/lvchange
./sbin/pvck linked to ./sbin/lvchange
x ./usr/bin/lifcp, 36864 bytes, 72 tape blocks
x ./usr/bin/lifls, 24576 bytes, 48 tape blocks
x ./usr/bin/lifrm, 20480 bytes, 40 tape blocks
x ./usr/bin/basename, 12288 bytes, 24 tape blocks
x ./usr/bin/chgrp, 20480 bytes, 40 tape blocks
x ./usr/bin/cmp, 20480 bytes, 40 tape blocks
x ./usr/bin/cp, 28672 bytes, 56 tape blocks
x ./usr/bin/cut, 20480 bytes, 40 tape blocks
x ./usr/bin/dd, 24576 bytes, 48 tape blocks
x ./usr/bin/dirname, 12288 bytes, 24 tape blocks
x ./usr/bin/egrep, 24576 bytes, 48 tape blocks
x ./usr/bin/expr, 20480 bytes, 40 tape blocks
x ./usr/bin/false, 12288 bytes, 24 tape blocks
./usr/bin/fgrep linked to ./usr/bin/egrep
x ./usr/bin/getopts, 163 bytes, 1 tape blocks
./usr/bin/grep linked to ./usr/bin/egrep
x ./usr/bin/hostname, 12288 bytes, 24 tape blocks
x ./usr/bin/kill, 16384 bytes, 32 tape blocks
x ./usr/bin/ln, 16384 bytes, 32 tape blocks
x ./usr/bin/model, 24576 bytes, 48 tape blocks
x ./usr/bin/ps, 36864 bytes, 72 tape blocks
x ./usr/bin/pwd, 12288 bytes, 24 tape blocks
x ./usr/bin/rm, 28672 bytes, 56 tape blocks
./usr/bin/rmdir linked to ./usr/bin/rm
x ./usr/bin/sed, 40960 bytes, 80 tape blocks
x ./usr/bin/sort, 40960 bytes, 80 tape blocks
x ./usr/bin/tar, 45056 bytes, 88 tape blocks
x ./usr/bin/touch, 16384 bytes, 32 tape blocks
x ./usr/bin/true, 12288 bytes, 24 tape blocks
x ./usr/bin/uname, 16384 bytes, 32 tape blocks
x ./usr/bin/wc, 16384 bytes, 32 tape blocks
x ./usr/bin/compress, 28672 bytes, 56 tape blocks
x ./usr/bin/ed, 57344 bytes, 112 tape blocks
x ./usr/bin/find, 57344 bytes, 112 tape blocks
x ./usr/bin/getopt, 12288 bytes, 24 tape blocks
x ./usr/bin/id, 16384 bytes, 32 tape blocks
x ./usr/bin/more, 65536 bytes, 128 tape blocks
x ./usr/bin/tail, 20480 bytes, 40 tape blocks
./usr/bin/uncompress linked to ./usr/bin/compress
./usr/bin/zcat linked to ./usr/bin/compress
x ./usr/bin/bdf, 20480 bytes, 40 tape blocks
x ./usr/bin/diff, 36864 bytes, 72 tape blocks
x ./usr/bin/mt, 16384 bytes, 32 tape blocks
x ./usr/bin/ftp, 114688 bytes, 224 tape blocks
x ./usr/bin/rcp, 45056 bytes, 88 tape blocks
x ./usr/bin/remsh, 28672 bytes, 56 tape blocks
x ./usr/bin/ex, 241664 bytes, 472 tape blocks
./usr/bin/vi linked to ./usr/bin/ex
x ./usr/lib/uxbootlf, 707584 bytes, 1382 tape blocks
x ./usr/lib/libHcurses.sl symbolic link to /usr/lib/libcurses.1
x ./usr/lib/libM.1 symbolic link to ./libm.1
x ./usr/lib/libc.1, 1515520 bytes, 2960 tape blocks
x ./usr/lib/libc.2, 1359872 bytes, 2656 tape blocks
x ./usr/lib/libcl.2, 987136 bytes, 1928 tape blocks
x ./usr/lib/libcurses.1, 155648 bytes, 304 tape blocks
x ./usr/lib/libdld.1, 12288 bytes, 24 tape blocks
x ./usr/lib/libdld.2, 20480 bytes, 40 tape blocks
x ./usr/lib/libdld.sl symbolic link to ./libdld.2
x ./usr/lib/libfab.1, 20480 bytes, 40 tape blocks
x ./usr/lib/libfab.sl symbolic link to ./libfab.1
x ./usr/lib/libm.1, 98773 bytes, 193 tape blocks
x ./usr/lib/libm.2, 184320 bytes, 360 tape blocks
x ./usr/lib/libm.sl symbolic link to ./libm.2
x ./usr/lib/libnss_files.1, 36864 bytes, 72 tape blocks
x ./usr/lib/libpthread.1, 106496 bytes, 208 tape blocks
x ./usr/lib/libsec.2, 114688 bytes, 224 tape blocks
x ./usr/lib/libstd_v2.2, 1511424 bytes, 2952 tape blocks
x ./usr/lib/libxcurses.1, 315392 bytes, 616 tape blocks
x ./usr/lib/nls/msg/C/dcerpc.cat, 13755 bytes, 27 tape blocks
x ./usr/lib/nls/msg/C/cpp.cat, 10542 bytes, 21 tape blocks
x ./usr/lib/libnsl.1, 602112 bytes, 1176 tape blocks
x ./usr/lib/libnsl.sl symbolic link to /usr/lib/libnsl.1
x ./usr/lib/libnss_dns.1, 20480 bytes, 40 tape blocks
x ./usr/lib/libxti.2, 110592 bytes, 216 tape blocks
x ./usr/lib/sw/ui/C/smc_addhost.ui, 2571 bytes, 6 tape blocks
x ./usr/lib/sw/ui/C/smc_analyze.ui, 4663 bytes, 10 tape blocks
x ./usr/lib/sw/ui/C/smc_bundles.ui, 1775 bytes, 4 tape blocks
x ./usr/lib/sw/ui/C/smc_chgloc.ui, 3634 bytes, 8 tape blocks
x ./usr/lib/sw/ui/C/smc_defs.h, 24742 bytes, 49 tape blocks
x ./usr/lib/sw/ui/C/smc_depend.ui, 2824 bytes, 6 tape blocks
x ./usr/lib/sw/ui/C/smc_details.ui, 3990 bytes, 8 tape blocks
x ./usr/lib/sw/ui/C/smc_dsa.ui, 8100 bytes, 16 tape blocks
x ./usr/lib/sw/ui/C/smc_init.ui, 708 bytes, 2 tape blocks
x ./usr/lib/sw/ui/C/smc_install.ui, 4018 bytes, 8 tape blocks
x ./usr/lib/sw/ui/C/smc_jobopts.ui, 113847 bytes, 223 tape blocks
x ./usr/lib/sw/ui/C/smc_jobs.ui, 20222 bytes, 40 tape blocks
x ./usr/lib/sw/ui/C/smc_list.ui, 1962 bytes, 4 tape blocks
x ./usr/lib/sw/ui/C/smc_menudefs.h, 1792 bytes, 4 tape blocks
x ./usr/lib/sw/ui/C/smc_options.ui, 5889 bytes, 12 tape blocks
x ./usr/lib/sw/ui/C/smc_patch.ui, 2527 bytes, 5 tape blocks
x ./usr/lib/sw/ui/C/smc_remove.ui, 3289 bytes, 7 tape blocks
x ./usr/lib/sw/ui/C/smc_rmsourc.ui, 2411 bytes, 5 tape blocks
x ./usr/lib/sw/ui/C/smc_sched.ui, 4591 bytes, 9 tape blocks
x ./usr/lib/sw/ui/C/smc_selalt.ui, 2804 bytes, 6 tape blocks
x ./usr/lib/sw/ui/C/smc_seldpt.ui, 2404 bytes, 5 tape blocks
x ./usr/lib/sw/ui/C/smc_session.ui, 2180 bytes, 5 tape blocks
x ./usr/lib/sw/ui/C/smc_softinf.ui, 5653 bytes, 12 tape blocks
x ./usr/lib/sw/ui/C/smc_softwar.ui, 18847 bytes, 37 tape blocks
x ./usr/lib/sw/ui/C/smc_source.ui, 4902 bytes, 10 tape blocks
x ./usr/lib/sw/ui/C/smc_targets.ui, 12190 bytes, 24 tape blocks
x ./usr/lib/sw/ui/C/smc_task.ui, 5805 bytes, 12 tape blocks
x ./usr/lib/sw/help/C/sduhelp.hv, 28436 bytes, 56 tape blocks
x ./usr/lib/sw/help/C/sduhelp.hvk, 5145 bytes, 11 tape blocks
x ./usr/lib/sw/help/C/sduhelp00.ht, 215428 bytes, 421 tape blocks
x ./usr/lib/sw/help/C/sduhelp01.ht, 14210 bytes, 28 tape blocks
x ./usr/lib/libcma.1, 462848 bytes, 904 tape blocks
x ./usr/lib/libcma.2, 483328 bytes, 944 tape blocks
x ./usr/lib/libcma.sl symbolic link to ./libcma.2
x ./usr/lib/libd4r.1, 45056 bytes, 88 tape blocks
x ./usr/lib/libd4r.sl symbolic link to ./libd4r.1
x ./usr/lib/libdce.1, 4235264 bytes, 8272 tape blocks
x ./usr/lib/libdce.2, 4292608 bytes, 8384 tape blocks
x ./usr/lib/libdce.sl symbolic link to ./libdce.2
x ./usr/lib/libdcekt.1, 4427776 bytes, 8648 tape blocks
x ./usr/lib/libsis.sl, 1044480 bytes, 2040 tape blocks
x ./usr/lib/dld.sl, 155648 bytes, 304 tape blocks
x ./usr/lib/libdc.sl, 45056 bytes, 88 tape blocks
x ./usr/lib/libsmapi.2, 86016 bytes, 168 tape blocks
x ./usr/sbin/devnm, 16384 bytes, 32 tape blocks
x ./usr/sbin/diskinfo, 24576 bytes, 48 tape blocks
x ./usr/sbin/insf symbolic link to /sbin/mksf
x ./usr/sbin/ioinit symbolic link to /sbin/ioinit
x ./usr/sbin/ioscan symbolic link to /sbin/ioscan
x ./usr/sbin/mknod symbolic link to /sbin/mknod
x ./usr/sbin/mount symbolic link to /sbin/mount
x ./usr/sbin/reboot symbolic link to /sbin/reboot
x ./usr/sbin/setboot, 20480 bytes, 40 tape blocks
x ./usr/sbin/swapon, 28672 bytes, 56 tape blocks
x ./usr/sbin/umount symbolic link to /sbin/umount
x ./usr/sbin/chroot, 12288 bytes, 24 tape blocks
x ./usr/sbin/rvxdump symbolic link to /usr/lbin/fs/vxfs/vxdump
x ./usr/sbin/rvxrestore symbolic link to /usr/lbin/fs/vxfs/vxrestore
x ./usr/sbin/vxdump symbolic link to /usr/lbin/fs/vxfs/vxdump
x ./usr/sbin/vxrestore symbolic link to /usr/lbin/fs/vxfs/vxrestore
x ./usr/sbin/mk_kernel, 27494 bytes, 54 tape blocks
x ./usr/sbin/swagentd, 651264 bytes, 1272 tape blocks
x ./usr/sbin/swacl, 2154496 bytes, 4208 tape blocks
./usr/sbin/swconfig linked to ./usr/sbin/swacl
./usr/sbin/swcopy linked to ./usr/sbin/swacl
./usr/sbin/swinstall linked to ./usr/sbin/swacl
./usr/sbin/swlist linked to ./usr/sbin/swacl
x ./usr/sbin/swmodify, 1257472 bytes, 2456 tape blocks
./usr/sbin/swpackage linked to ./usr/sbin/swmodify
./usr/sbin/swreg linked to ./usr/sbin/swacl
./usr/sbin/swremove linked to ./usr/sbin/swacl
./usr/sbin/swverify linked to ./usr/sbin/swacl
x ./usr/share/lib/terminfo/h/hp, 1448 bytes, 3 tape blocks
x ./usr/share/lib/terminfo/v/vt100, 1358 bytes, 3 tape blocks
x ./usr/share/lib/terminfo/w/wy60, 1673 bytes, 4 tape blocks
x ./usr/conf/gen/templates/generic, 542 bytes, 2 tape blocks
x ./usr/ccs/lbin/cpp, 290816 bytes, 568 tape blocks
x ./usr/lbin/fs/vxfs/vxdump, 110592 bytes, 216 tape blocks
x ./usr/lbin/fs/vxfs/vxrestore, 126976 bytes, 248 tape blocks
x ./usr/lbin/sw/control_utils, 131332 bytes, 257 tape blocks
x ./usr/lbin/swagent, 1536000 bytes, 3000 tape blocks
x ./usr/lbin/sysadm/create_sysfile, 24576 bytes, 48 tape blocks
x ./usr/lbin/sysadm/system_prep, 10000 bytes, 20 tape blocks
x ./usr/obam/lbin/gethelp, 1236992 bytes, 2416 tape blocks
x ./usr/obam/lbin/ui_exec, 12288 bytes, 24 tape blocks
x ./usr/obam/lib/libIDMawrt.1, 1995529 bytes, 3898 tape blocks
x ./usr/obam/lib/libIDMawrt.sl symbolic link to ./libIDMawrt.1
x ./usr/obam/lib/libobam.1, 1032192 bytes, 2016 tape blocks
x ./usr/obam/lib/libobam.sl symbolic link to ./libobam.1
x ./usr/obam/lib/obam_aw.dmb, 149652 bytes, 293 tape blocks
x ./usr/obam/lib/help/C/ui/ui.sdl, 81025 bytes, 159 tape blocks
x ./usr/contrib/bin/gunzip, 90112 bytes, 176 tape blocks
./usr/contrib/bin/gzip linked to ./usr/contrib/bin/gunzip
x ./sbin/awk, 397312 bytes, 776 tape blocks
x ./sbin/cat, 208896 bytes, 408 tape blocks
x ./sbin/chmod, 249856 bytes, 488 tape blocks
x ./sbin/chown, 258048 bytes, 504 tape blocks
x ./sbin/date, 241664 bytes, 472 tape blocks
x ./sbin/frecover, 368640 bytes, 720 tape blocks
x ./sbin/fs/cdfs/mount, 229376 bytes, 448 tape blocks
x ./sbin/fs/cdfs/umount symbolic link to /sbin/fs/hfs/umount
x ./sbin/fs/hfs/fsck, 339968 bytes, 664 tape blocks
x ./sbin/fs/hfs/mount, 229376 bytes, 448 tape blocks
x ./sbin/fs/hfs/umount, 192512 bytes, 376 tape blocks
x ./sbin/fs/vxfs/fsck, 495616 bytes, 968 tape blocks
x ./sbin/fs/vxfs/mount, 458752 bytes, 896 tape blocks
x ./sbin/fs/vxfs/umount symbolic link to /sbin/fs/hfs/umount
x ./sbin/fsck symbolic link to /sbin/fs_wrapper
x ./sbin/init, 299008 bytes, 584 tape blocks
x ./sbin/insf, 405504 bytes, 792 tape blocks
x ./sbin/ioinit, 221184 bytes, 432 tape blocks
x ./sbin/ioscan, 229376 bytes, 448 tape blocks
x ./sbin/ls, 286720 bytes, 560 tape blocks
x ./sbin/mkboot, 274432 bytes, 536 tape blocks
x ./sbin/mkdir, 200704 bytes, 392 tape blocks
x ./sbin/mknod, 192512 bytes, 376 tape blocks
x ./sbin/mount, 274432 bytes, 536 tape blocks
x ./sbin/mv, 241664 bytes, 472 tape blocks
x ./sbin/reboot, 245760 bytes, 480 tape blocks
x ./sbin/stty, 208896 bytes, 408 tape blocks
x ./sbin/umount, 221184 bytes, 432 tape blocks
x ./sbin/restore, 290816 bytes, 568 tape blocks
x ./sbin/pax, 389120 bytes, 760 tape blocks
x ./dev/config, 0 bytes, 0 blocks, character device
x ./dev/null, 0 bytes, 0 blocks, character device
x ./dev/console, 0 bytes, 0 blocks, character device
x ./dev/kmem, 0 bytes, 0 blocks, character device
x ./dev/mem, 0 bytes, 0 blocks, character device
x ./dev/rroot, 0 bytes, 0 blocks, character device
x ./dev/root, 0 bytes, 0 blocks, character device
x ./dev/tty, 0 bytes, 0 blocks, character device
x ./dev/syscon, 0 bytes, 0 blocks, character device
x ./dev/systty, 0 bytes, 0 blocks, character device
x ./tmp/set_locale, 3305 bytes, 7 tape blocks
x ./var/adm/sw/security/_ACL, 40 bytes, 1 tape blocks
x ./var/adm/sw/security/_OWNER, 62 bytes, 1 tape blocks
x ./var/adm/sw/security/_PROD_DFLT_ACL, 55 bytes, 1 tape blocks
x ./var/adm/sw/security/_SOC_DFLT_ACL, 55 bytes, 1 tape blocks
x ./var/adm/sw/security/secrets, 15 bytes, 1 tape blocks
x ./var/adm/sw/defaults, 1383 bytes, 3 tape blocks
x ./var/opt/ignite/local/manifest/template.def, 14441 bytes, 29 tape blocks
x ./opt/ignite/share/man/man1m.Z/print_manifest.1m, 1499 bytes, 3 tape blocks
x ./opt/ignite/binpa/print_manifest, 61440 bytes, 120 tape blocks
x ./opt/ignite/bin symbolic link to /opt/ignite/binpa
x ./etc/group, 184 bytes, 1 tape blocks
x ./etc/passwd, 332 bytes, 1 tape blocks
x ./etc/magic, 8794 bytes, 18 tape blocks
x ./etc/hosts, 486 bytes, 1 tape blocks
x ./etc/services, 10908 bytes, 22 tape blocks
x ./etc/inetsvcs.conf, 15 bytes, 1 tape blocks
x ./etc/nsswitch.conf, 444 bytes, 1 tape blocks
x ./configure3, 2015232 bytes, 3936 tape blocks
x ./monitor_bpr, 1568768 bytes, 3064 tape blocks
* Download_mini-system: Complete
* Loading_software: Begin
* Installing boot area on disk.
* Enabling swap areas.
* Backing up LVM configuration for "vg00".
* Number of archives to install: 1
* Processing the archive source (Recovery Archive).
* Mon Aug 31 10:11:27 EDT 2020: Starting archive load of the source
(Recovery Archive).
* Positioning the tape (/dev/rmt/c4t3d0BESTn).
* Looking for Archive...
* Found the Archive Position. Now load the Archive.
* Archive extraction from tape is beginning. Please wait.
pax_iux: [offset 0g+1m+0k+566]: I/O error
pax_iux: [offset 0g+1m+0k+566]: I/O error
pax_iux: opt/webadmin/obam/obam5_0.jar : The archive file appears to be corrupt.
pax_iux: /dev/rmt/c4t3d0BEST : This doesn't look like a tar archive
pax_iux: /dev/rmt/c4t3d0BEST : Skipping to next file...
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
DIAGNOSTIC SYSTEM WARNING:
The diagnostic logging facility has started receiving excessive
errors from the I/O subsystem. I/O error entries will be lost
until the cause of the excessive I/O logging is corrected.
If the diaglogd daemon is not active, use the Daemon Startup command
in stm to start it.
If the diaglogd daemon is active, use the logtool utility in stm
to determine which I/O subsystem is logging excessive errors.
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+580]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: [offset 0g+1m+0k+581]: I/O error
pax_iux: opt/sfwk/contrib/lib/apache-ant/ant.jar : The archive file appears to be corrupt.
ERROR: Cannot load OS archive (Recovery Archive)

The configuration process has incurred an error, choose one of the following options

1) abort and reboot
2) ignore error and continue
3) push a shell for troubleshooting the problem
(At any time within the shell, type "exit" to return to this menu)

Choose an option from above [1 by default] :2
* Executing user specified script:
"/opt/ignite/data/scripts/os_arch_post_l".
* Running in recovery mode (os_arch_post_l).
* Running the ioinit command ("/sbin/ioinit -c")
* Creating device files via the insf command.
insf: Installing special files for sdisk instance 0 address 0/0/2/0.0.0.0
insf: Installing special files for sdisk instance 1 address 0/1/1/0.0.0
insf: Installing special files for stape instance 0 address 0/3/1/0.3.0
insf: Installing special files for pseudo driver dlpi
insf: Installing special files for pseudo driver kepd
insf: Installing special files for pseudo driver framebuf
insf: Installing special files for pseudo driver sad
* Running "/opt/upgrade/bin/tlinstall -v" and correcting transition link
permissions.
* Constructing the bootconf file.
* Setting primary boot path to "0/1/1/0.0.0".
NOTE: tlinstall is searching filesystem - please be patient
NOTE: Successfully completed
* Loading_software: Complete
======= 08/31/20 11:23:04 EDT Building the new kernel.
* Build_Kernel: Begin
NOTE: Since the /stand/vmunix kernel is already in place, the kernel will
not be re-built. Note that no mod_kernel directives will be processed.
* Build_Kernel: Complete
* Boot_From_Client_Disk: Begin
======= 08/31/20 11:23:07 EDT Rebooting machine as expected.
NOTE: Rebooting system.

sync'ing disks (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty

Closing open logical volumes...
Done

Any idea to try to restore it?

Thank you again

[LuisFSalas]

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 1000 MHz Active Functional 67108864 67108864
1 1000 MHz Idle Functional 67108864 67108864

Central Bus Speed (in MHz) : 200
Available Memory : 4194304 KB
Good Memory Required : Not initialized. Defaults to 32 MB.

Primary boot path: 0/1/1/0.0
Alternate boot path: 0/0/2/0.3
Console path: 0/7/1/1.0
Keyboard path: 0/0/4/0.0

Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.
Proceeding...

Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL booting hpux

Boot
: disk(0/1/1/0.0.0.0.0.0.0;0)/stand/vmunix
10944512 + 2215936 + 22823144 start 0x1fafe8

alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
[Osxinit]: Allocated ots_timeout_lock [4027fac0]
igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0
igelan1: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/2/1/0

System Console is on the Built-In Serial Interface
Entering cifs_init...
Initialization finished successfully... slot is 9
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Starting the STREAMS daemons-phase 1
Checking root file system.
file system is clean - log replay is not required
Root check done.
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 4192256 Kbytes, lockable: 3112640 Kbytes, available: 3586532 Kbytes

insf: Installing special files for sdisk instance 0 address 0/0/2/0.0.0.0
insf: Installing special files for sdisk instance 1 address 0/1/1/0.0.0
insf: Installing special files for stape instance 0 address 0/3/1/0.3.0
Volume group "/dev/vg00" has been successfully changed.
* Running the ioinit command ("/sbin/ioinit -c")
* Creating device files via the insf command.
insf: Installing special files for hub instance 0 address 0/0/1/0.1
insf: Installing special files for hub instance 1 address 0/0/1/1.1
insf: Installing special files for sdisk instance 0 address 0/0/2/0.0.0.0
insf: Installing special files for sctl instance 0 address 0/0/2/0.0.7.0
insf: Installing special files for sctl instance 1 address 0/0/2/0.1.7.0
insf: Installing special files for sdisk instance 1 address 0/1/1/0.0.0
insf: Installing special files for sctl instance 2 address 0/1/1/0.7.0
insf: Installing special files for sctl instance 3 address 0/1/1/1.7.0
insf: Installing special files for stape instance 0 address 0/3/1/0.3.0
insf: Installing special files for sctl instance 4 address 0/3/1/0.7.0
insf: Installing special files for sctl instance 5 address 0/3/1/1.7.0
insf: Installing special files for asio0 instance 0 address 0/7/1/0
insf: Installing special files for asio0 instance 1 address 0/7/1/1
insf: Installing special files for ipmi instance 0 address 16
insf: Installing special files for pseudo driver cn
insf: Installing special files for pseudo driver mm
insf: Installing special files for pseudo driver devkrs
insf: Installing special files for pseudo driver ptym
insf: Installing special files for pseudo driver ptys
insf: Installing special files for pseudo driver ip
insf: Installing special files for pseudo driver arp
insf: Installing special files for pseudo driver rawip
insf: Installing special files for pseudo driver tcp
insf: Installing special files for pseudo driver udp
insf: Installing special files for pseudo driver stcpmap
insf: Installing special files for pseudo driver nuls
insf: Installing special files for pseudo driver netqa
insf: Installing special files for pseudo driver dmem
insf: Installing special files for pseudo driver diag0
insf: Installing special files for pseudo driver telm
insf: Installing special files for pseudo driver tels
insf: Installing special files for pseudo driver tlclts
insf: Installing special files for pseudo driver tlcots
insf: Installing special files for pseudo driver iomem
insf: Installing special files for pseudo driver tlcotsod
insf: Installing special files for pseudo driver dev_config
insf: Installing special files for pseudo driver strlog
insf: Installing special files for pseudo driver sad
insf: Installing special files for pseudo driver echo
insf: Installing special files for pseudo driver dlpi
insf: Installing special files for pseudo driver ptm
insf: Installing special files for pseudo driver pts
insf: Installing special files for pseudo driver beep
insf: Installing special files for pseudo driver framebuf
insf: Installing special files for pseudo driver diag1
insf: Installing special files for pseudo driver klog
insf: Installing special files for pseudo driver sy
insf: Installing special files for pseudo driver kepd
insf: Installing special files for pseudo driver diag2
insf: Installing special files for pseudo driver root
* Boot_From_Client_Disk: Complete
* Run_SD_Configure_Scripts: Begin
* Run_SD_Configure_Scripts: Complete
* Run_Postconfigure_Scripts: Begin
* Applying the networking information.
* Applying the timezone: GMT0BST.
* Run all specified post-configure scripts.
* Executing user specified script:
"/opt/ignite/data/scripts/os_arch_post_c".
* Running in recovery mode (os_arch_post_c).
* Executing user specified commands.
Volume Group configuration for /dev/vg00 has been saved in /etc/lvmconf/vg00.conf
* Run_Postconfigure_Scripts: Complete
======= 08/31/20 16:26:48 BST Installation complete: Successful

####### # #
# # # #
# # # #
# # ###
# # # #
# # # #
####### # #

NOTE: Rebooting system.

sync'ing disks (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty

Closing open logical volumes...
Done

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 1000 MHz Active Functional 67108864 67108864
1 1000 MHz Idle Functional 67108864 67108864

Central Bus Speed (in MHz) : 200
Available Memory : 4194304 KB
Good Memory Required : Not initialized. Defaults to 32 MB.

Primary boot path: 0/1/1/0.0
Alternate boot path: 0/0/2/0.3
Console path: 0/7/1/1.0
Keyboard path: 0/0/4/0.0

Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.
Proceeding...

Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL booting hpux

Boot
: disk(0/1/1/0.0.0.0.0.0.0;0)/stand/vmunix
10944512 + 2215936 + 22823144 start 0x1fafe8

alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
[Osxinit]: Allocated ots_timeout_lock [40220ac0]
igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0
igelan1: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/2/1/0

System Console is on the Built-In Serial Interface
Entering cifs_init...
Initialization finished successfully... slot is 9
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Starting the STREAMS daemons-phase 1
Checking root file system.
file system is clean - log replay is not required
Root check done.
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 4192256 Kbytes, lockable: 3112640 Kbytes, available: 3586532 Kbytes

/sbin/ioinitrc:
insf: Installing special files for ipmi instance 0 address 16
insf: Installing special files for pseudo driver framebuf
/sbin/krs_sysinit:
ln: Warning! /stand/krs/_stand_vmunix.krs and /stand/krs_lkg//_stand_vmunix.krs are identical
ln: Warning! /stand/krs/system.krs and /stand/krs_lkg//system.krs are identical

/sbin/bcheckrc:
Checking for LVM volume groups and Activating (if any exist)
Volume group "/dev/vg00" has been successfully changed.
vxfs fsck: sanity check: root file system OK (mounted read/write)
Checking hfs file systems
/sbin/fsclean: /dev/vg00/lvol1 (mounted) ok
HFS file systems are OK, not running fsck
Checking vxfs file systems
/dev/vg00/lvol3 :
vxfs fsck: sanity check: root file system OK (mounted read/write)
/dev/vg00/lvol4 :
vxfs fsck: sanity check: /dev/vg00/lvol4 OK

Cleaning /etc/ptmp...
(c)Copyright 1983-2000 Hewlett-Packard Co., All Rights Reserved.
(c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California
(c)Copyright 1980, 1984, 1986 Novell, Inc.
(c)Copyright 1986-1992 Sun Microsystems, Inc.
(c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology
(c)Copyright 1989-1993 The Open Software Foundation, Inc.
(c)Copyright 1986 Digital Equipment Corp.
(c)Copyright 1990 Motorola, Inc.
(c)Copyright 1990, 1991, 1992 Cornell University
(c)Copyright 1989-1991 The University of Maryland
(c)Copyright 1988 Carnegie Mellon University
(c)Copyright 1991-2000 Mentat Inc.
(c)Copyright 1996 Morning Star Technologies, Inc.
(c)Copyright 1996 Progressive Systems, Inc.
(c)Copyright 1991-2000 Isogon Corporation, All Rights Reserved.

RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure by the U.S. Government is subject to
restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in
Technical Data and Computer Software clause in DFARS 252.227-7013.

Hewlett-Packard Company
3000 Hanover Street
Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set
forth in FAR 52.227-19(c)(1,2).

Open Source Software has been installed on this system. See
/opt/OpenSource/etc/copyright

/sbin/auto_parms: DHCP access is disabled (see /etc/auto_parms.log)

cat: Cannot open /usr/local/graphon/etc/gold.conf: No such file or directory

HP-UX Start-up in progress
__________________________

Configure system crash dumps ............................................. OK
Removing old vxvm files .................................................. OK
Mount file systems ....................................................... OK
Update kernel and loadable modules ....................................... N/A
Initialize loadable modules .............................................. NOTICE: modld: Module already loaded
OK
Setting hostname ......................................................... OK
Start Kernel Logging facility ............................................ N/A
Set privilege group ...................................................... N/A
Display date ............................................................. N/A
Copy processor logs to /var/tombstones ................................... FAIL *
Save system crash dump if needed ......................................... N/A
Start evp ................................................................ OK
Enable auxiliary swap space .............................................. OK
Start syncer daemon ...................................................... OK
Configure Loopback interfaces (lo0) ...................................... OK
Configure EARLY NDD tunables ............................................. OK
Configuring all unconfigured software filesets ........................... OK
Configuring PFIL ......................................................... OK
Starting IPFilter ........................................................ NOTICE: modld: Module already loaded
OK
Recover editor crash files ............................................... OK
Clean UUCP ............................................................... FAIL *
List and/or clear temporary files ........................................ OK
Clean up old log files ................................................... OK
Start system message logging daemon ...................................... OK
Start pty allocator daemon ............................................... Aug 31 16:30:35 OMN01 syslogd: /var/adm/syslog/mail.log: No such file or directory
Aug 31 16:30:35 OMN01 syslogd: /var/adm/syslog/syslog.log: No such file or directory
OK
Configuring OLA/R interface .............................................. N/A
Start network tracing and logging daemon ................................. OK
Configure HP igelan Gigabit Ethernet interfaces .......................... OK
Configure HP iether Gigabit Ethernet interfaces .......................... OK
Configure HP Gigabit Ethernet interfaces ................................. OK
Configure HP Ethernet interfaces ......................................... OK
Create PCI FDDI device files. ............................................ OK
Configure HP 100BASE-T interfaces ........................................ N/A
Configure VLAN interfaces ................................................ OK
Configure LAN interfaces ................................................. OK
Start name server daemon ................................................. N/A
Start OTS ................................................................ FAIL *
Starting HP-UX Secure Shell .............................................. FAIL *
Start NFS core subsystem ................................................. OK
Start NIS+ server subsystem .............................................. OK
Start NIS+ client subsystem .............................................. OK
Start NIS server subsystem ............................................... OK
Start NIS client subsystem ............................................... OK
Start NFS client subsystem ............................................... OK
Start the Trusted Mode with NIS+ subsystem ............................... N/A
Configure pseudo devices for MAC/LLA access .............................. OK
Start multicast routing daemon ........................................... N/A
Start Internet services daemon ........................................... OK
Start dynamic routing daemon ............................................. N/A
Start router discover protocol daemon .................................... N/A
Configuring PPP Interface ................................................ OK
Start RARP protocol daemon ............................................... N/A
Start remote system status daemon ........................................ N/A
Configuring man pages for Internet Services .............................. OK
Starting mail daemon ..................................................... N/A
Starting outbound connection daemons for DDFA software ................... N/A
Start SNMP Master Network Management daemon .............................. N/A
Start OSPF MIB Network Management subAgent ............................... N/A
Start SNMP HP-UNIX Network Management subAgent ........................... N/A
Start SNMP MIB-2 Network Management subAgent ............................. N/A
Start SNMP Trap Dest Network Management subAgent ......................... N/A
Start DCE daemons ........................................................ N/A
Start SNMP PCI FDDI Network Management subAgent .......................... OK
Start RPC daemon if needed ............................................... N/A
Start CIM cimserver subsystem ............................................ N/A
Start Isogon License Server Daemon ....................................... N/A
Initialize Instant Capacity .............................................. OK
Start remote boot daemon ................................................. N/A
Starting X Font Server at TCP port 7000 .................................. N/A
Start vt daemon .......................................................... N/A
Starting UDC server ...................................................... N/A
Start time synchronization ............................................... N/A
Start accounting ......................................................... N/A
Install/Load XF86 DLKM Helper Modules .................................... OK
Starting the password/group assist subsystem ............................. OK
Starting HP Disk Array Manager daemons. .................................. OK
Starting disk array monitor daemons. ..................................... OK
Start print spooler ...................................................... N/A
Starting HP Distributed Print Service .................................... OK
Start clock daemon ....................................................... OK
Start diagnostic subsystem ............................................... cron aborted: can't change directory to the crontab directory.
OK
Start auditing subsystem ................................................. N/A
Start audio server daemon ................................................ N/A
Start Distributed Single Logical Screen daemon ........................... N/A
Start USB hub daemon ..................................................... OK
SAM System administration configuration .................................. OK
OVPA performance software is being started. .............................. N/A
Initialize the fax devicefile ............................................ OK
Starting ObAM Application Server ......................................... N/A
Initialize Software Distributor agent daemon ............................. OK
Starting CIFS Client ..................................................... N/A
Configure HP RAID SA interfaces .......................................... N/A
Starting Event Monitoring Service ........................................ OK
Start EMS SNMP subagent .................................................. OK
Configure HP Fibre Channel Mass Storage interfaces ....................... OK
Configure HP Internal RAID interfaces .................................... N/A
Configure for Java ....................................................... OK
Configuring Ultra320 SCSI Mass Storage interfaces ........................ OK
Configure HP Fibre Channel Tachyon TL/TS Mass Storage interfaces ......... OK
Configuring HP Fibre Channel FCD Mass Storage interfaces ................. OK
Start NFS server subsystem ............................................... OK
Start X print server(s) .................................................. N/A
Starting the GraphOn Login Daemon ........................................ N/A
Starting the NSUE (Marconi Communications Software Systems) subsystem .... nohup: /usr/nsue/bin/RunNSUE: No such file or directory
OK
Starting OVTrcSrv... ..................................................... FAIL *
Starting OVCtrl... ....................................................... OK
Start CDE login server ................................................... OK
Starting PRNGD (Pseudo Random Number Generator Daemon) ................... N/A

* - An error has occurred !
* - Refer to the file /etc/rc.log for more information.

The system is ready.

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:cim1 "/opt/wbem/lbin/cimserverd"

GenericSysName [HP Release B.11.11] (see /etc/issue)
Console Login:

[Patrick Wallek]

I don't know what all you have downloaded.  If you have downloaded the DVD set that is the HP-UX installation set, then once you create DVDs from the ISOs, you should be able to boot from DVD 1.

As far as your backup goes, I don't know that there is much you can do.  It appears that the tape is corrupted.

[Bertram Stoeckler]

> cat ./netscapedirsvr6/nds-nsperl/var/opt/netscape/servers/lib/nsperl5.005_03/lib/pa-risc2.0-thread/core/xsub.h

If the "cat" command produces garbage, then there is one thing you may try to do. It could be that the file is "tar"-ed or "gzip"-ed. So check if the "file" command is able to determine the file-type. (It reads the header)

file ./netscapedirsvr6/nds-nsperl/var/opt/netscape/servers/lib/nsperl5.005_03/lib/pa-risc2.0-thread/core/xsub.h

If the file command is not able to report the type, then you definetelly have a corrupted DVD/CD ROM.

You can also simply try to "untar" or "ungzip" it. 

cat ./netscapedirsvr6/nds-nsperl/var/opt/netscape/servers/lib/nsperl5.005_03/lib/pa-risc2.0-thread/core/xsub.h | gunzip > /tmp/my_xsub.h 

Hope that helps.

[Steven Schweda]

> Anyway, I am still not sure that ISO's can be bootable.

   A CD-R (or DVD-R) made from a bootable CD-ROM (or DVD-ROM) image
("ISO") file should be bootable.  I do it all the time, on various
operating systems.

> An ISO image can create a bootable DVD. That is how HPE distributes
> HP-UX now.

   Except that for 11.11, it's a set of CD-ROMs, not DVDs.

> https://fsck.technology/software/HP/HP-UX%20Install%20Media/

   Note the (sub-DVD) sizes of the files here:

      https://fsck.technology/software/HP/HP-UX%20Install%20Media/HP-UX%2011iv1%20%282005-09%29/

   Posting a long transcript without an explanation of what you're doing
to get it is not as helpful as it could be.

> [...] It appears that the tape is corrupted.

   Yup.

   Of course, "ISO" is a standards organization (https://www.iso.org);
"ISO 9660" is a particular ISO standard which "Specifies the volume and
file structure of compact read-only optical disks (CD-ROM) [...]".  (And
"COVID" is a lame abbreviation of "COVID-19", as in COrona Virus ID-19
(2019 being the year in which it was identified).  "ID" without the
"-19" is rather pointless.)