hpux 11.11 : hard disk failure

[chad_c]

hello....we are running an hpux 11.11 parisc 4440 .....we received the following hard drive failure

Unknown ------- 11:09:48 07/25/08 riovo Kernel OS vmunix Logical drive 0 transitioned from RECOVERING to OK
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix Hot Spare: No
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix Configured: Yes
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix Enclosure Bay: 8
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix Failure Reason: INVALID TARGET TSH
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix SCSI ID: 0
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix Channel: 1
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix disk failure:
Unknown ------- 10:24:03 07/25/08 riovo Kernel OS vmunix CISS: RAID SA controller on hardware path 0/5/2/0 has detected a physical

can anyone shed some light on how can we found out the cause of this and current status of the 5 disk array?

rgds,
chad

[Pedro Cirne]

Hi,

Post here the output of the following command:

#ioscan -fnCdisk

Pedro

[chad_c]

riovo# ioscan -fnCdisk
Class I H/W Path Driver S/W State H/W Type Description
=========================================================================
disk 0 0/0/3/0.0.0.0 sdisk CLAIMED DEVICE TEAC DV-28E-C
/dev/dsk/c0t0d0 /dev/rdsk/c0t0d0
disk 1 0/1/1/0.0.0 sdisk CLAIMED DEVICE HP 146 GST3146807LC
/dev/dsk/c2t0d0 /dev/rdsk/c2t0d0
disk 2 0/1/1/0.1.0 sdisk CLAIMED DEVICE HP 146 GST3146807LC
/dev/dsk/c2t1d0 /dev/rdsk/c2t1d0
disk 3 0/5/2/0.0.0 sdisk CLAIMED DEVICE COMPAQ LOGICAL VOLUME
/dev/dsk/c4t0d0 /dev/rdsk/c4t0d0
riovo#

[SKR_1]

You need to place a case with HP for this , if you have any support contract with HP.

Are you getting this alerts again and again.

I think this is an informational event for any of the disk failure which has been recovered automatically and is up and available now.

Thanks,

SKR

[chad_c]

can anyone shed some light on some good hpux commands to gather and check status of the 5 disk array?

[Pedro Cirne]

Hi,

Post the output of:

#ioscan -fn
#dmesg

Pedro

[Torsten.]

The messages are coming from your Smartarray controller - this is a hardware RAID.

Inspect your /dev/ciss_ driver (for example /dev/ciss3) from ioscan -fn

and perform

# sautil /dev/ciss3
# saconfig /dev/ciss3

and post the result.

[chad_c]

thank you....here are the listed command output

riovo# ioscan -fn
Class I H/W Path Driver S/W State H/W Type Description
=============================================================================
root 0 root CLAIMED BUS_NEXUS
ioa 0 0 sba CLAIMED BUS_NEXUS System Bus Adapter (880)
ba 0 0/0 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
tty 0 0/0/1/0 asio0 CLAIMED INTERFACE PCI SimpleComm (103c1290)
/dev/diag/mux0 /dev/mux0 /dev/tty0p0
tty 1 0/0/1/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)
/dev/GSPdiag1 /dev/diag/mux1 /dev/mux1 /dev/tty1p0 /dev/tty1p2 /dev/tty1p4
usb 0 0/0/2/0 hcd CLAIMED INTERFACE NEC USB Interface
usbhub 0 0/0/2/0.1 hub CLAIMED DEVICE USB Root Hub
usb 1 0/0/2/1 hcd CLAIMED INTERFACE NEC USB Interface
usbhub 1 0/0/2/1.1 hub CLAIMED DEVICE USB Root Hub
/dev/hub
usb 2 0/0/2/2 ehci CLAIMED INTERFACE NEC USB Interface
sideba 0 0/0/3/0 side_ba CLAIMED INTERFACE CMD IDE controller
ext_bus 0 0/0/3/0.0 side CLAIMED INTERFACE IDE Primary Channel
target 0 0/0/3/0.0.0 tgt CLAIMED DEVICE
disk 0 0/0/3/0.0.0.0 sdisk CLAIMED DEVICE TEAC DV-28E-C
/dev/dsk/c0t0d0 /dev/rdsk/c0t0d0
target 1 0/0/3/0.0.7 tgt CLAIMED DEVICE
ctl 0 0/0/3/0.0.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c0t7d0
ext_bus 1 0/0/3/0.1 side CLAIMED INTERFACE IDE Secondary Channel
target 2 0/0/3/0.1.7 tgt CLAIMED DEVICE
ctl 1 0/0/3/0.1.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c1t7d0
ba 1 0/1 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ext_bus 2 0/1/1/0 c8xx CLAIMED INTERFACE SCSI C1010 Ultra160 Wide LVD A6829-60101
target 3 0/1/1/0.0 tgt CLAIMED DEVICE
disk 1 0/1/1/0.0.0 sdisk CLAIMED DEVICE HP 146 GST3146807LC
/dev/dsk/c2t0d0 /dev/rdsk/c2t0d0
target 4 0/1/1/0.1 tgt CLAIMED DEVICE
disk 2 0/1/1/0.1.0 sdisk CLAIMED DEVICE HP 146 GST3146807LC
/dev/dsk/c2t1d0 /dev/rdsk/c2t1d0
target 5 0/1/1/0.7 tgt CLAIMED DEVICE
ctl 2 0/1/1/0.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c2t7d0
ext_bus 3 0/1/1/1 c8xx CLAIMED INTERFACE SCSI C1010 Ultra160 Wide LVD A6829-60101
target 6 0/1/1/1.7 tgt CLAIMED DEVICE
ctl 3 0/1/1/1.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c3t7d0
lan 0 0/1/2/0 igelan CLAIMED INTERFACE HP A6825-60101 PCI 1000Base-T Adapter
ba 2 0/2 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
lan 1 0/2/1/0 iether CLAIMED INTERFACE HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter
lan 2 0/2/1/1 iether CLAIMED INTERFACE HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter
ba 3 0/4 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
graphics 0 0/4/1/0 graph3 CLAIMED INTERFACE PCI Display (103c108b)
ba 4 0/5 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
ext_bus 4 0/5/2/0 ciss CLAIMED INTERFACE PCI RAID160 SmartArray Controller
/dev/ciss4
target 7 0/5/2/0.0 tgt CLAIMED DEVICE
disk 3 0/5/2/0.0.0 sdisk CLAIMED DEVICE COMPAQ LOGICAL VOLUME
/dev/dsk/c4t0d0 /dev/rdsk/c4t0d0
target 8 0/5/2/0.7 tgt CLAIMED DEVICE
ctl 4 0/5/2/0.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c4t7d0
ba 5 0/6 lba CLAIMED BUS_NEXUS Local PCI-X Bus Adapter (783)
lan 3 0/6/1/0 iether CLAIMED INTERFACE HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter
lan 4 0/6/1/1 iether CLAIMED INTERFACE HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter
memory 0 8 memory CLAIMED MEMORY Memory
ipmi 0 16 ipmi CLAIMED INTERFACE IPMI Controller
/dev/ipmi
processor 0 128 processor CLAIMED PROCESSOR Processor
processor 1 129 processor CLAIMED PROCESSOR Processor
processor 2 136 processor CLAIMED PROCESSOR Processor
processor 3 137 processor CLAIMED PROCESSOR Processor
riovo# dmesg

Jul 25 15:22
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: autofs_link(): File system was registered at index 3.
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 6.
0 sba
0/0 lba
0/0/1/0 asio0
0/0/1/1 asio0
0/0/2/0 hcd
0/0/2/0.1 hub
0/0/2/1 hcd
0/0/2/1.1 hub
0/0/2/2 ehci
0/0/3/0 side_ba
0/0/3/0.0 side
0/0/3/0.0.0 tgt
0/0/3/0.0.0.0 sdisk
0/0/3/0.0.7 tgt
0/0/3/0.0.7.0 sctl
0/0/3/0.1 side
0/0/3/0.1.7 tgt
0/0/3/0.1.7.0 sctl
0/1 lba
c8xx BUS: 2 SCSI C1010 Ultra160 Wide LVD A6829-60101 assigned CPU: 0
0/1/1/0 c8xx
0/1/1/0.0 tgt
0/1/1/0.0.0 sdisk
0/1/1/0.1 tgt
0/1/1/0.1.0 sdisk
0/1/1/0.7 tgt
0/1/1/0.7.0 sctl
c8xx BUS: 3 SCSI C1010 Ultra160 Wide LVD A6829-60101 assigned CPU: 1
0/1/1/1 c8xx
0/1/1/1.7 tgt
0/1/1/1.7.0 sctl
0/1/2/0 igelan
0/2 lba
0/2/1/0 iether
0/2/1/1 iether
0/4 lba
Variable size pages used to map 1000 graf pages at ffffffffc1000000
0/4/1/0 graph3
0/5 lba
CISS: RAID SA controller on hardware path 0/5/2/0 is now online.
0/5/2/0 ciss
0/5/2/0.0 tgt
0/5/2/0.0.0 sdisk
0/5/2/0.7 tgt
0/5/2/0.7.0 sctl
0/6 lba
0/6/1/0 iether
0/6/1/1 iether
8 memory
16 ipmi
128 processor
129 processor
136 processor
137 processor

System Console is on the Built-In Serial Interface
igelan0: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/1/2/0
iether1: INITIALIZING HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter at hardware path 0/2/1/0
iether2: INITIALIZING HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter at hardware path 0/2/1/1
iether3: INITIALIZING HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter at hardware path 0/6/1/0
iether4: INITIALIZING HP A7012-60001 PCI/PCI-X 1000Base-T Dual-port Adapter at hardware path 0/6/1/1
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Dump device table: (start & size given in 1-Kbyte blocks)
entry 0000000000000000 - major is 31, minor is 0x21000; start = 953184, size = 8388608
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 8386560 Kbytes, lockable: 6456500 Kbytes, available: 7416860 Kbytes

CISS: RAID SA controller on hardware path 0/5/2/0 has detected a physical
disk failure:
Channel: 1
SCSI ID: 0
Failure Reason: INVALID TARGET TSH
Enclosure Bay: 8
Configured: Yes
Hot Spare: No
CISS: RAID SA controller on hardware path 0/5/2/0 has detected a logical
drive status change:
Logical drive 0 transitioned from OK to INTERIM RECOVERY
Drive type: RAID 5 - Distributed Data Guarding
CISS: RAID SA controller on hardware path 0/5/2/0 has detected a logical
drive status change:
Logical drive 0 transitioned from INTERIM RECOVERY to READY FOR RECOVERY
Drive type: RAID 5 - Distributed Data Guarding
CISS: RAID SA controller on hardware path 0/5/2/0 has detected a logical
drive status change:
Logical drive 0 transitioned from READY FOR RECOVERY to RECOVERING
Drive type: RAID 5 - Distributed Data Guarding
CISS: RAID SA controller on hardware path 0/5/2/0 has detected a logical
drive status change:
Logical drive 0 transitioned from RECOVERING to OK
Drive type: RAID 5 - Distributed Data Guarding
riovo#
riovo# sautil /dev/ciss3

******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.06 ****
**** ****
**** (C) Copyright 2003, 2004 Hewlett-Packard Development Company, L.P. ****
******************************************************************************


sautil: Unrecognized device file specified: "/dev/ciss3"

sautil: Error - File open failed
sautil: No such file or directory, errno=2


RAID SA device files (/dev/cissX) found using "/usr/sbin/ioscan -kfnd ciss":

Class I H/W Path Driver S/W State H/W Type Description
=================================================================
ext_bus 4 0/5/2/0 ciss CLAIMED INTERFACE PCI RAID160 SmartArray Controller
/dev/ciss4

Run "sautil run_startup_script" if you suspect that the device file is missing or corrupted.
Run "sautil" to view usage screen.

riovo# saconfig /dev/ciss3


saconfig (/dev/ciss3): Error - File open failed
saconfig (/dev/ciss3): No such file or directory, errno=2


SmartArray RAID device files (/dev/cissX) found using "/usr/sbin/ioscan -kfnd ciss":

Class I H/W Path Driver S/W State H/W Type Description
=================================================================
ext_bus 4 0/5/2/0 ciss CLAIMED INTERFACE PCI RAID160 SmartArray Controller
/dev/ciss4

Run "sautil run_startup_script" if you suspect that the device file is missing or corrupted.
riovo#

[Torsten.]

Read my post again!

ciss3 was an EXAMPLE!

Your device is /dev/ciss4 !

# sautil /dev/ciss4
# saconfig /dev/ciss4

[chad_c]

makes sense...thank you.


******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.06 ****
**** ****
**** (C) Copyright 2003, 2004 Hewlett-Packard Development Company, L.P. ****
******************************************************************************



---- DRIVER INFORMATION ------------------------------------------------------

Driver State........................ READY

---- CONTROLLER INFORMATION --------------------------------------------------

Controller Product Number........... A7143A
Controller Product Name............. HP RAID160 SA SCSI Controller
Hardware Path....................... 0/5/2/0
Serial Number....................... P746C0DDARO0W8
Device File......................... /dev/ciss4
Hardware Revision................... 'A'
Boot Block Revision................. 3.24
Firmware Revision (running)......... 3.54
Firmware Revision (in ROM).......... 3.54
Firmware Revision (inactive)........ 3.54
# of Logical Drives................. 1
# of Physical Disks Configured...... 5
# of Physical Disks Detected........ 4
Logical Drive Rebuild Priority...... 118 (high)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... enabled
SCSI Transfer Detection Mode........ Auto Detect


---- ARRAY ACCELERATOR (CACHE) INFORMATION -----------------------------------

Array Accelerator Board Present?.... yes
Cache Configuration Status.......... cache enabled
Cache Ratio......................... 50% Read / 50% Write
Total Cache Size (MB)............... 256
Read Cache........................ 112
Write Cache....................... 112
Transfer Buffer................... 032
Battery Pack Count.................. 2
Battery Status (pack #1)............ ok
Battery Status (pack #2)............ ok


---- LOGICAL DRIVE SUMMARY ---------------------------------------------------

# RAID Size Status

0 5 208392 MB OK


---- SCSI DEVICE SUMMARY -----------------------------------------------------

Location Ch ID Type Capacity Status

N/A 1 0 N/A N/A FAILED
external 1 1 DISK 72.8 GB OK
external 1 7 PROCESSOR
external 3 0 DISK 72.8 GB OK
external 3 1 DISK 72.8 GB OK
external 3 2 DISK 72.8 GB SPARE (activated)
external 3 15 PROCESSOR


---- SCSI BUS SUMMARY --------------------------------------------------------

External Internal
Ch LVD_Mode Connector Connector

1 YES YES -
2 YES - -
3 YES YES -
4 YES - -


---- LOGICAL DRIVE 0 ---------------------------------------------------------

Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding)
Logical Drive Size.................. 208392 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 4

Participating Physical Disk(s)...... Ch:ID
1: 0 <-- NOT RESPONDING
1: 1
3: 0
3: 1

Participating Spare Disk(s)......... Ch:ID
3: 2 <-- activated for 1:0

Stripe Size......................... 16 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0x140E1144
Media Exchange Detected?............ no


---- SCSI DEVICE 1:1 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 1
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288285
Device Serial Number............................. 3KP0Q20N00007548UG25
Device Firmware Version.......................... HPB3
SCSI Transfer Rate (actual)...................... Ultra-160
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... no
Packetized SCSI supported...................... no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ no
Currently running QAS (U320 only).............. no



---- SCSI DEVICE 1:7 [PROCESSOR] ---------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 7
Device Type...................................... PROCESSOR
Device Vendor ID................................. COMPAQ
Device Product ID................................ PROLIANT 4L7E*DT
SCSI Transfer Rate (maximum)..................... Ultra-320


---- SCSI DEVICE 3:0 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 3
SCSI ID.......................................... 0
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07289BC4
Device Serial Number............................. DNA1P6707LPY0627
Device Firmware Version.......................... HPB1
SCSI Transfer Rate (actual)...................... Ultra-160
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. INVALID TARGET TSH

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... no
Packetized SCSI supported...................... no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ no
Currently running QAS (U320 only).............. no



---- SCSI DEVICE 3:1 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 3
SCSI ID.......................................... 1
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07289BC4
Device Serial Number............................. DSA1P6B02K1A0648
Device Firmware Version.......................... HPB1
SCSI Transfer Rate (actual)...................... Ultra-160
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... no
Packetized SCSI supported...................... no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ no
Currently running QAS (U320 only).............. no



---- SCSI DEVICE 3:2 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 3
SCSI ID.......................................... 2
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... SPARE (activated)
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288285
Device Serial Number............................. 3KP0PS9H00007548N7BR
Device Firmware Version.......................... HPB3
SCSI Transfer Rate (actual)...................... Ultra-160
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... yes
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... no
Packetized SCSI supported...................... no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ no
Currently running QAS (U320 only).............. no



---- SCSI DEVICE 3:15 [PROCESSOR] --------------------------------------------

Connector Location............................... external
Channel Number................................... 3
SCSI ID.......................................... 15
Device Type...................................... PROCESSOR
Device Vendor ID................................. COMPAQ
Device Product ID................................ PROLIANT 4L7E*DB
SCSI Transfer Rate (maximum)..................... Ultra-320


---- DIAGRAM OF EXTERNAL CONNECTORS ON BRACKET -------------------------------

========---========
| |
| ULTRA-3 <--- LOOK FOR THIS LOGO
| / \ |
| <- |
| \ / |
| |
| * * |
| * * * * |
(Ch 1)---> * * * * <--- (Ch 2)
| * * * * |
| * * |
| |
| * * |
| * * * * |
(Ch 3)---> * * * * <--- (Ch 4)
| * * * * |
| * * |
| |
| |
~ ~ ~ ~ ~


******************************************************************************
**** End of SAUTIL Output ****
******************************************************************************

******************** SmartArray RAID Controller /dev/ciss4 ********************

Auto-Fail Missing Disks at Boot = enabled
Cache Configuration Status = cache enabled
Cache Ratio = 50% Read / 50% Write

---------- PHYSICAL DRIVES ----------

Location Ch ID Size Status

External 1 1 72.8 GB OK
External 3 0 72.8 GB OK
External 3 1 72.8 GB OK
External 3 2 72.8 GB SPARE

---------- LOGICAL DRIVE 0 ----------

RAID Level = 5
Size = 208392 MB
Stripe Size = 16 KB
Status = OK

Participating Physical Drive(s):

Ch ID

1 0
1 1
3 0
3 1

Participating Spare Drive(s):

Ch ID

3 2

[Torsten. · Accepted solution]

I guess you can find it by yourself.

N/A 1 0 N/A N/A FAILED
external 1 1 DISK 72.8 GB OK
external 1 7 PROCESSOR
external 3 0 DISK 72.8 GB OK
external 3 1 DISK 72.8 GB OK
external 3 2 DISK 72.8 GB SPARE (activated)


Do you see the first line?


Participating Physical Disk(s)...... Ch:ID
1: 0 <-- NOT RESPONDING



This disk is bad and needs replacement - spare disk is activated.

Do you see a red LED?

[chad_c]

excellent work....thank you.

[chad_c]

.