I/O and dump

[mark.M]

rp3440
OS ll.00
what is this???

Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1

P1 0/1/1/0.1 intscsia.1 Random access media 1

P2 0/1/1/0.0 intscsia.0 Random access media 1



Main Menu: Enter command or menu > bo p0
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.38 OCT 26, 1994

ISL booting hpux (;0):INSTALL

Boot
: disk(0/0/2/0.0.0.0.0.0.0;0):WINSTALL
8962064 + 1174208 + 1998104 start 0x278968



Firmware Version 45.11

Duplex Console IO Dependent Code (IODC) revision 1



Stored message buffer up to panic:

System Panic:

linkstamp: Thu Jul 19 11:39:34 MDT 2001
_release_version: @(#)B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PS
T 1997
__kern_ci_revision: $Header: kern_sequence.c,v 1.6.106.512 97/11/05 18:01:46 mso
sa Exp $

panic: set_machine_parameters_64: Unidentified cpu type returned from PDC_MODEL

PC-Offset Stack Trace (read across, top of stack is 1st):
0x0037c8ac 0x004e8bc8 0x004e8a28
0x004e7040 0x0038bdfc 0x00278e9c
End Of Stack



*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative.

[baiju_3 · Accepted solution]

Does this model support 11.0 ? I am not sure , see the link it says 11i v1 and v2.

http://www.hp.com/products1/servers/rackoptimized/rp3400_series/index.html


thx,
bl.

[Adisuria Wangsadinata_1]

Hi,

To be frank with you, the answer of your question is : this is the error message when you try to install something on your system.

You need to check on the system log (SL) on your MP (Management Processor) :

1. from your console, press 'CTRL+B'
2. input the user/password
(Admin/Admin OR Oper/Oper)
3. type SL > E > T
4. check also the power status (PS) :
type CM > PS
5. check the LED status on your system
from MP prompt, type VFP

You can check the PIM information from BCH mode, goto INFO >PIMINFO

If you can describe more detail about the situation, it's very help to narrow down to the exact problem.

As stated on the message above, it's better you log a call also to HP.

Hope this information can help you.

Cheers,
AW

[mark.M]

thank you lalb
i'm slov....

[Adisuria Wangsadinata_1]

Hi,

See the url below :

Supported system on HP-UX 11.i v1:
http://www.docs.hp.com/en/5990-7279/ch03s01.html

Supported system on HP-UX 11.00 :
http://www.docs.hp.com/en/5990-6721/ch01s08.html

RP3440 is for HP-UX 11.i NOT HP-UX 11.00.

So it's looks like you used wrong version to install RP3440 OR some problem on the hardware (for troubleshooting check previous reply from me).

Hope this information can help you.

Cheers,
AW

[Arunvijai_4]

As per the specification, It will support only 11i v1 and 11iv2. Take a look this page,

http://www.hp.com/products1/servers/rackoptimized/rp3400_series/specifications.html

-Arun