system not booting from disk & also from CD-ROM drive

[sbb]

Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


POTENTIAL BOOT DEVICES

Path# Device Path Device Type
----- ----------------- -------------------------
P0 scsiB.6 HP 73.4GMAW3073NP


Main Menu: Enter command or menu > boot p0
Interact with IPL (Y, N, or Cancel)?> y

Booting...
Boot IO Dependent Code (IODC) revision 2


HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL> hpux -is

Boot
: disk(0/2/1/1.6.0.0.0.0.0;0)/stand/vmunix
13344768 + 2494464 + 21779800 start 0x2dbd68
alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
iether0: INITIALIZING HP PCI
Firmware Version 2.13

Duplex Console IO Dependent Code (IODC) revision 1

Stored message buffer up to panic:
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
0 sba
0/0 lba
0/2 lba
Initializing the Ultra320 SCSI Controller at 0/2/1/0. Controller firmware versi5
0/2/1/0 mpt
SCSI Ultra320 0/2/1/0 instance 0: The driver is now online
0/2/1/0.7 tgt
0/2/1/0.7.0 sctl
Initializing the Ultra320 SCSI Controller at 0/2/1/1. Controller firmware versi5
0/2/1/1 mpt
SCSI Ultra320 0/2/1/1 instance 1: The driver is now online
0/2/1/1.6 tgt
0/2/1/1.6.0 sdisk
0/2/1/1.7 tgt
0/2/1/1.7.0 sctl
0/3 lba
0/3/1/0 hcd
0/3/1/0.1 hub
0/3/1/0.1.2 hid
0/3/1/1 hcd
0/3/1/1.1 hub
0/3/1/1.1.2 hid
0/3/1/2 ehci
0/3/2/0 side_ba
0/3/2/0.0 side
0/3/2/0.0.7 tgt
0/3/2/0.0.7.0 sctl
0/3/2/0.1 side
0/3/2/0.1.7 tgt
0/3/2/0.1.7.0 sctl
0/3/3/0 iether
0/4 lba
0/4/0/0 gvid_core
8 memory
16 ipmi
17 asio0
18 asio0
128 processor
129 processor
iether0: INITIALIZING HP PCI 1000Base-T Built-in at hardware path 0/3/3/0

System Console is on the Built-In Serial Interface
WARNING: ROOT device 0x1f016000 is a non-LVM partition, disallowed on LVM disk.
WARNING: ROOT device 0x1f016000 has been deconfigured (set to 0xffffffff).


-----------------------------------------------------
| |
| SYSTEM HALTING during LVM Configuration |
| |
Non-lvm root on LVM disk
| |
-----------------------------------------------------


linkstamp: Thu Feb 21 11:59:34 IST 2008
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: C$
panic: LVM: Configuration failure

PC-Offset Stack Trace (read across, top of stack is 1st):
0x002ee558 0x0061f434 0x0061ed2c
0x0061f0a0 0x0045fcb0 0x00572014
0x00461a20 0x0018e634 0x002dc364
End Of Stack

Trap Type 15 (Data page fault):
Instruction Address (pcsq.pcoq) = 0x0.0x5763d0
Instruction (iir) = 0x531a0020 (load/store)
Target Address (isr.ior) = 0x0.0x0000000000000010
Base Register (gr24) = 0x0000000000000000
Savestate Ptr (ssp) = 0x7d71000.0x400003ffffff0f68
Savestate Return Pointer (ss_rp) = 0x0000000000000000

System Panic:

linkstamp: Thu Feb 21 11:59:34 IST 2008
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: C$
panic: Data page fault

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative.

Firmware Version 2.13

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State CoProcessor Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 1000 MHz Active Functional 64 MB/64 MB
1 1000 MHz Idle Functional 64 MB/64 MB

Central Bus Speed (in MHz) : 200
Available Memory : 4194304 KB
Good Memory Required : Not initialized. Defaults to 32 MB.

Primary boot path: scsiA.0
0/2/1/0.0
Alternate boot path: lan.0.0.0.0
0/3/3/0
Console path: serial_A.643
17.643
Keyboard path: usb0
0/3/1/0.0
Keyboard path ignored for serial consoles.




Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

Boot terminated.


---- Main Menu ---------------------------------------------------------------

Command Description
------- -----------
BOot [PRI|ALT|] Boot from specified path
PAth [PRI|ALT|CON|KEY []] Display or change a path
SEArch [DIsplay|[[IPL] []]] Search for boot devices

COnfiguration menu Displays or sets boot values
INformation menu Displays hardware information
SERvice menu Displays service commands

DIsplay Redisplay the current menu
HElp [|] Display help for menu or command
RESET Restart the system
----
Main Menu: Enter command or menu >

[Suraj K Sankari]

Hi,
Do you know how many disks are there in your server ? Is there any CD or DVD attached into the server ?
because in "sea" reasult its showing only 1 disk.

Path# Device Path Device Type
----- ----------------- -------------------------
P0 scsiB.6 HP 73.4GMAW3073NP

and while booting the server this error also showing "Non-lvm root on LVM disk"

this means no lvm disk are found by the system

do one thing switch off the server take out all disks, CD or DVD ROM from server and fix again then do a "sea"

Suraj

[avizen9]

looks os doesnt detect hardisk.

[johnsonpk]

Hi,

Try booting in lvm maintenance mode and restore the boot/root definition


on isl prompt issue the below command

hpux -lm

once booted

#lvlnboot -r /dev/vg00/lvol3 (for root lvol)
#lvlnboot -s /dev/vg00/lvol2 (for swap)
#lvlnboot -b /dev/vg00/lvol1 (for stand)

then reboot the system with reboot commad

Thanks!!
Johnson