- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- X-Terminal, Entria
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-23-2001 09:58 AM
тАО05-23-2001 09:58 AM
I have changed no software but I did change from using thin net to 10 base T. Which is connected to the internet using a cisco 10/100
switch [Catalyst 3500 XL 12 port]. I also had to change all of my ip addresses.
When I turn on xterm It recognizes 10 base t
but puts a big red x through icon. Then gives error messages "NoEtherTwist hub detected"
then for each of the two file servers that it is suppose to down load from it says that they are down or unreachable.
from xterm configure screens when I go to telnet option I can telnet into both of them.
I ran all enware test on unix boxes and could find no problems
Does anyone know how I might correct problem
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-25-2001 10:45 AM
тАО05-25-2001 10:45 AM
Re: X-Terminal, Entria
We have a similar setup here. I have an Entria C3230A with release B.07.11. When I first power up the unit I have the red X through the 10BaseT card with the No EtherTwist hub detected message. After the downloading of the X server software is done, The "X" goes away and the Xterm boots to broadcast. I'd be interested in seeing what you Xterm settings for download are.
We have are network parameters set to "From Fields Below" and are defining the file server.
Ron
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-25-2001 12:21 PM
тАО05-25-2001 12:21 PM
Re: X-Terminal, Entria
s700_800 11.00 HP ENWARE B.07.11.00PL02 06/2000
PHSS_21692:1. PANap19385 - B.07.11 always switches to
the alternate file server
When both primary and alternate file-servers are
configured, the XTerm always downloads its code from
the alternate file server.2. PANap19485 - Envizex and 10/100 networking
When booting through an auto-sensing 10/100 switch
(HP ProCurve 10/100 J3295A), the Envizex could no longer
download the binaries/config. from the server. Messages are displayed :
"No cable" "No etherTwist hub detected"
3. PANap19539 - Envizex connected to auto-sensing 10-100 switch fails booting ...
maybe worth installing ? Or are you using hubs/routers ?
what about autosensing ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2001 06:50 AM
тАО06-06-2001 06:50 AM
Re: X-Terminal, Entria
>conf term
>int fa 0/8
>speed 100
>duplex half
>spanning-tree portfast
>exit
I still have the problem that these boxes are really slow on this switch. When I revert to using an old Catalyst 1900 these problems go away.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2001 06:59 AM