- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: Proliant ML330 G# and RH3 rev4 install problem
Operating System - Linux
1755661
Members
3547
Online
108837
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2005 08:46 AM
тАО07-13-2005 08:46 AM
Proliant ML330 G# and RH3 rev4 install problem
I am running a clean install
This machine does not recognize its ide drive.
It has a CSA-6 Ultra 100 controller with a maxtor disk.
The smart start disk does not supply a driver.
Any ideas?
CS
This machine does not recognize its ide drive.
It has a CSA-6 Ultra 100 controller with a maxtor disk.
The smart start disk does not supply a driver.
Any ideas?
CS
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2005 09:41 AM
тАО07-13-2005 09:41 AM
Re: Proliant ML330 G# and RH3 rev4 install problem
I'm assuming that this 'CSA-6 Ultra' wasn't supplied with the server by HP?
Could I get some more details on what the 'CSA-6' actually is? I asumme it's some sort of SATA controller, but.. Who makes it? Is it a SATA RAID controller?
I was unable to find any concrete details about it, let alone know what driver you should use for it.
Could I get some more details on what the 'CSA-6' actually is? I asumme it's some sort of SATA controller, but.. Who makes it? Is it a SATA RAID controller?
I was unable to find any concrete details about it, let alone know what driver you should use for it.
One long-haired git at your service...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2005 07:23 PM
тАО07-14-2005 07:23 PM
Re: Proliant ML330 G# and RH3 rev4 install problem
Even I also faced same type of issue. I think RHEL 3 U4 installer doesn't have driver for that controller. We need to manually provide driver that.
RHEL 4 U1 and SLES 9 SP1 will recognize the ide drive and installation goes fine.
RHEL 4 U1 and SLES 9 SP1 will recognize the ide drive and installation goes fine.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP