- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Autogen not getting correct number of processes
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:09 AM
тАО03-25-2010 08:09 AM
MAXPROCESSCNT parameter information:
Feedback information.
Old value was 3000, New value is 3000
Maximum Observed Processes: 325
- AUTOGEN parameter calculation has been overridden.
The calculated value was 2400. The value 3000
will be used in accordance with the following requirements:
MAXPROCESSCNT has been specified by a hard-coded value of 3000.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:12 AM
тАО03-25-2010 08:12 AM
Re: Autogen not getting correct number of processes
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:23 AM
тАО03-25-2010 08:23 AM
SolutionSYS$SYSTEM:AGEN$FEEEDBACK.EXE writes a text file SYS$SYSTEM:AGEN$FEEDBACK.DAT
which you can search
$ sear sys$system:agen$feedback.dat proc
PROCESSES_PEAK = 78
MAXPROCESSCNT_CUR = 227
Purely Personal Opinion
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:28 AM
тАО03-25-2010 08:28 AM
Re: Autogen not getting correct number of processes
$ mc agen$feedback
$ sea sys$system:agen$feedback.dat processcnt_cur
do you see the correct value or not ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:40 AM
тАО03-25-2010 08:40 AM
Re: Autogen not getting correct number of processes
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 08:47 AM
тАО03-25-2010 08:47 AM
Re: Autogen not getting correct number of processes
AUTOGEN collects and uses feedback data, if you tell it to.
Autogen saves the feedback data in the SAVPARAMS phase or during SHUTDOWN with SAVE_FEEDBACK.
Autogen uses the feedback data in the GENPARAMS phase unless you specify P3 as NOFEEDBACK or there is some problem with the feedback data.
Check for messages in SYS$SYSTEM:AGEN$PARAMS.REPORT.
If you want AUTOGEN to save the feedback data and use it, specify:
$ @SYS$UPDATE:AUTOGEN SAVPARAMS GENPARAMS
Then check SYS$SYSTEM:AGEN$PARAMS.REPORT. If everything looks o.k., invoke AUTOGEN again with:
$ @SYS$UPDATE:AUTOGEN GETDATA SETPARAMS
and then reboot.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 09:10 AM
тАО03-25-2010 09:10 AM
Re: Autogen not getting correct number of processes
@SYS$UPDATE:AUTOGEN SAVPARAMS SAVPARAMS
at a time of peak load is a good idea. Some of the collected data is a snapshot of current data.
You can do
@SYS$UPDATE:AUTOGEN GETDATA TESTFILES
to use the collected feedback to generate a report at another time.
Purely Personal Opinion
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 09:43 AM
тАО03-25-2010 09:43 AM
Re: Autogen not getting correct number of processes
@SYS$UPDATE:AUTOGEN SAVPARAMS SAVPARAMS
and then running AUTOGEN to use the data at a later date.
But even if you collect feedback at a high period, what if you run AUTOGEN at a low useage time and it collects the low useage feedback? Won't that distort the result as well?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 10:06 AM
тАО03-25-2010 10:06 AM
Re: Autogen not getting correct number of processes
the PEAK values will still be preserved as long as you don't reboot the system. If you have to reboot after a phase of high usage and before willing to run AUTOGEN, use the SAVE_FEEDBACK option during shutdown.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2010 03:02 PM
тАО03-25-2010 03:02 PM
Re: Autogen not getting correct number of processes
$ @AUTOGEN GETDATA TESTFILES
or
$ @AUTOGEN GETDATA SETPARAMS
etc.