netbeans 5.0 openvms itanium 8.2-1

[Lucinda_1]

installed java150
when installing ide server get error
The following product will be installed to destination:
HP I64VMS IDESERVER T5.0-1 DISK$I64SYS:[VMS$COMMON.]

Portion done: 0%...10%...20%...30%...50%...60%...70%
%PCSI-E-FILNOTPUR, error deleting DISK$I64SYS:[SYS0.SYSCOMMON.][IDE$SERVER.JARS]
ORG-NETBEANS-MODULES-JAVA-J2SEPROJECT-COPYLIBSTASK.JAR;1
-SYSTEM-W-BADFILENAME, bad file name syntax
Portion done: 80%...90%
%PCSI-I-PRCOUTPUT, output from subprocess follows ...
%DCL-E-OPENIN, error opening DEVI64$DKA0:[USER.PERRYL.NEWNETBEANS]HOTSPOT.COM; a
s input
-RMS-E-FNF, file not found
%PCSI-I-PRCERREXE, error executing: @SYS$STARTUP:IDE$STARTUP.COM

%PCSI-E-EXESTAFAIL, product supplied EXECUTE START procedure failed
-RMS-E-FNF, file not found
%PCSI-E-OPFAILED, operation failed
Terminating is strongly recommended. Do you want to terminate? [YES] y
%PCSI-E-CANCEL_WIP, termination resulted in an incomplete modification to the sy
stem
%PCSI-E-S_OPCAN, operation cancelled by request

[Wim Van den Wyngaert · Accepted solution]

From the release notes :

JDK 5.0 must be installed on an ODS-5 formatted disk.

Wim

[Lucinda_1]

this disk is, correct?
Disk DEVI64$DKA0:, device type HP 36.4G ST336754LC, is online, mounted, file-
oriented device, shareable, available to cluster, error logging is enabled.

Error count 0 Operations completed 196715
Owner process "" Owner UIC [SYSTEM]
Owner process ID 00000000 Dev Prot S:RWPL,O:RWPL,G:R,W
Reference count 194 Default buffer size 512
Current preferred CPU Id 1 Fastpath 1
Total blocks 71132960 Sectors per track 96
Total cylinders 7719 Tracks per cylinder 96
Logical Volume Size 71132960 Expansion Size Limit 2147475456

Volume label "I64SYS" Relative volume number 0
Cluster size 16 Transaction count 214
Free blocks 46647920 Maximum files allowed 16711679
Extend quantity 5 Mount count 1
Mount status System Cache name "_DEVI64$DKA0:XQPCACHE"
Extent cache size 64 Maximum blocks in extent cache 4664792
File ID cache size 64 Blocks in extent cache 47328
Quota cache size 0 Maximum buffers in FCP cache 4120
Volume owner UIC [1,1] Vol Prot S:RWCD,O:RWCD,G:RWCD,W:RWCD

Volume Status: ODS-5, subject to mount verification, protected subsystems
enabled, file high-water marking, write-through caching enabled.

[Ian Miller.]

Is your system disk in ODS5 format?
(see SHOW DEVICE/FULL DISK$I64SYS)

[Volker Halle]

Lucinda,

did you try $ SET PROC/PARSE=EXTENDED

Volker.

[Lucinda_1]

dka0 is the system disk

[Lucinda_1]

how will the set proc help install when the file is missing?

[Volker Halle]

Lucinda,

there is another error happening earlier, so you don't know, if the installation provided all the correct files.

The 'bad' filename is:

ORG-NETBEANS-MODULES-JAVA-J2SEPROJECT-COPYLIBSTASK.JAR;1
-SYSTEM-W-BADFILENAME, bad file name syntax

Try manually creating such a file on your DISK$I64SYS: and see what happens.

Volker.

[Lucinda_1]

the files existed
In the installation guide it tells you about the PCSI bug that will not allow deletion of files of a particular format. The solution is to delete the :[SYS0.SYSCOMMON.][IDE$SERVER]JARS.DIR file by hand after the product remove.

Then do the product install ideserver.

[Lucinda_1]

Here is where i am now


The following product will be installed to destination:
HP I64VMS IDESERVER T5.0-1 DISK$I64SYS:[VMS$COMMON.]

Portion done: 0%...10%...20%...30%...50%...60%...70%...80%...90%
%PCSI-I-PRCOUTPUT, output from subprocess follows ...
%DCL-E-OPENIN, error opening NOR$USER:[PERRYL.NEWNETBEANS]HOTSPOT.COM; as input
-RMS-E-FNF, file not found
%PCSI-I-PRCERREXE, error executing: @SYS$STARTUP:IDE$STARTUP.COM

%PCSI-E-EXESTAFAIL, product supplied EXECUTE START procedure failed
-RMS-E-FNF, file not found
%PCSI-E-OPFAILED, operation failed
Terminating is strongly recommended. Do you want to terminate? [YES]

[Volker Halle]

Lucinda,

how come IDE$STARTUP.COM is trying to execute a file on your user disk ?

%DCL-E-OPENIN, error opening NOR$USER:[PERRYL.NEWNETBEANS]HOTSPOT.COM; as input
-RMS-E-FNF, file not found

Are there some logicals defined to point to that non-existing file ? Or are there references to other DCL procedures, which are called by IDE$STARTUP.COM ?

Volker.

[Lucinda_1]

not a clue

[Volker Halle]

Lucinda,

as you terminated the installation, you can't look at the IDE$STARTUP.COM file.

Try extracting that file and have a look at it. Especially look at all lines containing '@'.

$ PROD EXTRACT FILE IDESERVER/SELECT=IDE$STARTUP.COM

Volker.

[Lucinda_1]

$ $ PROD EXTRACT FILE IDESERVER/SELECT=IDE$STARTUP.COM

The following product has been selected:
HP I64VMS IDESERVER T5.0-1 Layered Product

Do you want to continue? [YES] Y

Portion done: 0%...100%
$ TYPE IDE$STARTUP.COM
%TYPE-W-SEARCHFAIL, error searching for SYS$COMMON:[SYSMGR]IDE$STARTUP.COM;
-RMS-E-FNF, file not found
$ DIR DISK0:[*...]IDE$STARTUP.COM

Directory DEVI64$DKA0:[SYS0.SYSCOMMON.SYS$STARTUP]

IDE$STARTUP.COM;1

Total of 1 file.

Directory DEVI64$DKA0:[VMS$COMMON.SYS$STARTUP]

IDE$STARTUP.COM;1

Total of 1 file.

Grand total of 2 directories, 2 files.
$

[Lucinda_1]

$ type DEVI64$DKA0:[SYS0.SYSCOMMON.SYS$STARTUP]ide$startup.com
$! Startup command procedure to start the IDE Server
$! Version 1.0
$! This command procedure was generated during installation
$! on 5-DEC-2006 11:54:37.59
$ define/system/exec/trans=(conc, term) IDE$ROOT DEVI64$DKA0:[SYS0.SYSCOMMON.]
$ define/system/exec/trans=(conc, term) IDE$JARS_ROOT DEVI64$DKA0:[SYS0.SYSCOMMO
N.IDE$SERVER.JARS.]
$ define/system/exec/trans=(conc, term) IDE$ANT_ROOT DEVI64$DKA0:[SYS0.SYSCOMM
ON.IDE$SERVER.ANT.]
$ @DEVI64$DKA0:[SYS0.SYSCOMMON.][IDE$SERVER.COM]IDE$IDESTARTUP.COM
$ exit
$

[Volker Halle]

Lucinda,

so what does IDE$STARTUP.COM do or what other procedures does it call ?

Volker.

[Lucinda_1]

see answer above your question

[Volker Halle]

Lucinda,

what happens if you manually invoke @SYS$STARTUP:ide$startup.com ? Same error ?

What's in DEVI64$DKA0:[SYS0.SYSCOMMON.][IDE$SERVER.COM]IDE$IDESTARTUP.COM

Search all .COMs on your disk for the string 'hotspot'

As an example, you will get this type of error message like this:

$ @hotspot
%DCL-E-OPENIN, error opening USERDISK1:[HALLE]HOTSPOT.COM; as input
-RMS-E-FNF, file not found

Volker.

[Lucinda_1]

no HOTSPOT files on my system at all. However, I was able to
$ define/system ide$jdk_version 150

Then...

$ @sys$startup:ide$shutdown
$ @sys$startup:ide$startup

AND IT IS WORKING, I AM ABLE TO REMOTE CONNECT FROM MY DESKTOP

[Craig A Berry]

Hotspot is the Java bytecode engine used on Itanium. My best guess is that the NetBeans installation assumes you are installing from a process where Java is set up and running. It may well use Java for some pre- or post-installation tasks. You probably need to run something like:

@SYS$COMMON:[JAVA$150.COM]JAVA$150_SETUP

before installing NetBeans.

[Lucinda_1]

see solution above