- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Switching OMTOOL FAXSR from DecServer 700 port...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-17-2008 09:57 PM
тАО11-17-2008 09:57 PM
Switching OMTOOL FAXSR from DecServer 700 port to TTA port
if switching from a decserver 700 port setup?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-17-2008 10:04 PM
тАО11-17-2008 10:04 PM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
connector on it?
Which "alphaserver"? What's the connector on
it?
Normally, a PC-compatible, 9-pin Female to
25-pin Male, straight-through cable would be
my guess, but with no useful info to go on,
it's tough to do more than guess.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-18-2008 08:26 AM
тАО11-18-2008 08:26 AM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
connector on it?
Model MT1932ZDX. 25-pin female connector.
Which "alphaserver"? What's the connector on
it?
Alpha Server ES40 model. 9-pin TTA/TTB connecter, with obverse to the older DEC flat cable. Running the obverse of this plug to a standalone DC Flat cable connector /25-pin female connector. Then running a 25-pin male to 25-pin male straight thru cable to the multi-tech modem's female plug.
Normally, a PC-compatible, 9-pin Female to
25-pin Male, straight-through cable would be
my guess, but with no useful info to go on,
it's tough to do more than guess.
Need to shop for this type of 9-pin Female tpo 25-pin Male straight thru cable, I guess. Trying to impovise without one, and that could be the issue.
On the VMS side, the OMTOOL manual for FAXSR gives the commands:
$ SET TERMINAL devicename /SPEED=19200/NOMODEM/PERM
( I used TTB0 for devicename )
Then you are supposed to be able to test the modem using SET HOST:
$ SET HOST devicename /DTE
and test ATZ... TEST ATE1...etc.
All I get is this.....
$ set host ttb0/dte
%REM-I-TOQUIT, connection established
Press Ctrl/\ to quit, Ctrl/@ for command mode
CTRL/@ {enter}
DTEPAD> atz
%CLI-W-IVVERB, unrecognized command verb - check validity and spelling
\ATZ\
Message number 8007A5F4
DTEPAD> exit
CTRL/\
$
Think its the cable between the modem and the TTB0 9-ping plug on the back of the ES40 alphaserver? This is the lower of two 9-pin plugs on the ES40, and the other is for a serial Dec 420 monitor.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-18-2008 08:40 AM
тАО11-18-2008 08:40 AM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
the CTRL/@ is to get you to the DTEPAD command mode - not your modem!
Instead of doing CTRL/@, just enter your ATZ commands etc. You are already connected to the device. You then use CTRL/\ to break off the device, and back to DCL.
Duncan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-18-2008 09:20 AM
тАО11-18-2008 09:20 AM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
set host ttb0/dte
%REM-I-TOQUIT, connection established
Press Ctrl/\ to quit, Ctrl/@ for command mode
ATZ will not even show on the acreen, when typed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-18-2008 09:31 AM
тАО11-18-2008 09:31 AM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
The upper 9 pin port is for the RMC modem connection.
The lower port (with your VT420) is COM2, and the MMJ connector is COM1.
Try logging into the ES40 from the VT420 and you will see which port it is configure as. I would think that it is on TTB0.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-18-2008 10:40 AM
тАО11-18-2008 10:40 AM
Re: Switching OMTOOL FAXSR from DecServer 700 port to TTA port
Defined the port b for a vt400 series, and was able to log in as a serial console. Woohoo! And the TTA0 works is repsonding with the modem as well. Needs a little
fine tuning, bu this should work. Thanks for the wonderful input. David
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2012 08:21 AM
тАО02-15-2012 08:21 AM
OMTOOL FAXSR Manual
I have been recently asked to support a VMS 7.3 system running FAXSR - and in desperate need of the user's guide - Does anyone know where I can find a copy of the manual? (Preferably digital but old fashion paper manual will do just as well). Thanks in advance!