- Community Home
- >
- Welcome
- >
- Other HPE Product Questions
- >
- HPE 5940 SWITCH: Cannot ping after configure bond ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-19-2022 08:38 PM - last edited on 10-19-2022 11:27 PM by support_s
10-19-2022 08:38 PM - last edited on 10-19-2022 11:27 PM by support_s
HPE 5940 SWITCH: Cannot ping after configure bond LACP Layer3/4 with linux host
Hi Everyone,
I'm facing an issue when configuring bond LACP Layer3/4 with Linux host.
The bond0 configuration in the Linux node:
# cat /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=4 miimon=100 xmit_hash_policy=layer3+4"
MTU=1500
DEVICE=bond0
BOOTPROTO=none
IPADDR=10.0.0.15
NETMASK=255.255.255.0
NETWORK=10.0.0.0
BROADCAST=10.0.0.255
NM_CONTROLLED=no
IPV6_AUTOCONF=no
ONBOOT=yes
The switch configuration:
#
vlan 102
name TEST
#
interface Vlan-interface102
ip address 10.0.0.1 255.255.255.0
#
interface Route-Aggregation39
link-aggregation mode dynamic
link-aggregation load-sharing mode flexible
#
interface Route-Aggregation39.102
#
interface Ten-GigabitEthernet1/0/39
port link-mode route
port link-aggregation group 39
#
interface Ten-GigabitEthernet1/0/40
port link-mode route
port link-aggregation group 39
#
interface Ten-GigabitEthernet1/0/41
port link-mode route
port link-aggregation group 39
#
interface Ten-GigabitEthernet1/0/42
port link-mode route
port link-aggregation group 39
#
I could see Current state is UP and Line protocol state is UP for RAGG39 but still could not ping from Linux host (10.0.0.15) to Vlan-interface102 (10.0.0.1).
1_I did not configure IP address for RAGG39 because I think it will use IP of Vlan-interface102 (10.0.0.1) for load balancing, please correct me if I was wrong.
2_Is traffic from VLAN 102 will go through subinterface Route-Aggregation39.102 ?
Many thanks for any help!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-19-2022 11:25 PM
10-19-2022 11:25 PM
Re: HPE 5940 SWITCH: Cannot ping after configure bond LACP Layer3/4 with linux host
Hello @ehonnen,
Thank you for writing to us! HPE Networking forum has moved to Aruba Airheads Community and for HPE networking and Aruba product queries, request you to visit and post your query here: Aruba Airheads Community
You can refer to the below link as well for more details:
HPE Networking forum migration to Aruba Airheads c... - Hewlett Packard Enterprise Community
Sunitha G
I'm an HPE employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]