- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Early System Initialisation
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-01-2024 01:35 AM - last edited on 05-07-2024 04:51 PM by support_s
05-01-2024 01:35 AM - last edited on 05-07-2024 04:51 PM by support_s
Early System Initialisation
Hi just setting up a ML350 Gen10, Started normally several times. Checked iLo firmware and software. Out dated - nothing has been updated.
Rebooted and now Early system Intialisation reaches Memory Initialisation - Complete and hangs there.
Had a RSOD appear on one reboot whcih states "ia32 exception type 06 - invalid opcode exception"
Tried to update firmware (to v1.40 first) however receive error message "The file signature is invalid. Make sure you are suing a valid, signed flash file and try again. (EDIT - Hmmmm unzip and instal worked! Updates completed)
Critical Log Entries state (NOTE ALL CRITICAL ERRORS REMOVED POST UPDATES)
Uncorrectable MAchine Check Exception (Processor 1, APIC ID 0x00000000, Bank 0x00000001, Status 0xBF800000'00100134, Address 0x00000001B'CF8066c0, Misc 0x00000000. 00000086.
Uncorrectable MAchine Check Exception (Processor 1, APIC ID 0x00000000, Bank 0x00000006, Status 0xB3800000'00000E0B, Address 0x000000000'00000000, Misc 0x00000000. 00000000.
Server Critical Fault (service Information: Input Power Loss, Power Supply, Power Supply 1 (03h))
Where to from here please? ISSUE remains IA32 EXception type 06
- Tags:
- ProLiant Server
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-02-2024 07:32 AM
05-02-2024 07:32 AM
Re: Early System Initialisation
Hello,
You may restore all configuration settings to their manufacturing defaults.
You may refer to item 22 of the server's system board component diagram.
You may refer to "System maintenance switch descriptions" for performing this procedure.
Please refer to note 2 on this page.
For performing this procedure, power off the server, remove the power cable from the power supplies, remove the access panel and then set the system maintenance switch position 6 is set to the On position and then replace the access panel, connect the power cable and then power on the server.
Once a message indicates that a system maintenance switch is in on position and needs to be reversed, then power off the server, remove the power cable from the power supplies and then reverse the system maintenance switch's position.
Regards,
Views expressed herein are my personal opinion and are not the views of HPE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2024 08:48 PM - edited 05-05-2024 01:11 AM
05-04-2024 08:48 PM - edited 05-05-2024 01:11 AM
Re: Early System Initialisation
Thank you I have done that several times and I have installed latest SPP.
Now I have the following error. IA32
Now have the following error. IA32 Exception Type 0D - General Protection Exception
[cid:image001.png@01DA9E57.3DB20070]
[cid:image002.png@01DA9E57.3DB20070]
I tried to change the amount of memory.
It use to boot with 32Gb but as soon as I try 64Gb or more, it errors out. No does not boot at all!
Regards, James
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2024 08:51 PM
05-04-2024 08:51 PM
Re: Early System Initialisation
Thank you I have don that several times and I have installed latest SPP.
I tried to change the amount of memory. It boots with 32Gb but as soon as I try 64Gb or more, it errors out. I have 3x32Gb and 3x16Gb but only boots when I use 1 32Gb stick
I now have the following error.
IA32 exception Type 0D - General Protection Exception,
!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-05-2024 10:07 PM
05-05-2024 10:07 PM
Re: Early System Initialisation
Thank you I have done that several times and I have installed the latest SPP.
Now I have the following error. IA32 Exception Type 0D - General Protection Exceptions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-06-2024 07:00 PM
05-06-2024 07:00 PM
Re: Early System Initialisation
- This seems like a hardware issue. We need to review the operating system and AHS logs to provide a solution.
- Kindly raise a support ticket with HPE for further analysis.
I'm an HPE employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
![Accept or Kudo](/html/assets/hpe_banner_SME_signature.png)