- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ILO stops working after switch is rebooted
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2006 06:56 PM
тАО07-05-2006 06:56 PM
ILO stops working after switch is rebooted
Currently I have 3 servers where I can't ping the ILO IP address. All of these are connected to the same switch that was rebooted yesterday.
How do I get ILO to work again, WITHOUT rebooting the whole server?
I tried just disconnecting/connecting the cable in hope that it would start working again, but no no.
thanks for any help...
/Goran
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2006 08:54 PM
тАО07-05-2006 08:54 PM
Re: ILO stops working after switch is rebooted
have you lokked in the ILO Configuration during POST to get sure the get an IP Adress ?
You can look else in the Systemmanagement Hompage there should be an entry to configure the ILO Board.
greets from vienna,
Franz
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2006 09:25 PM
тАО07-05-2006 09:25 PM
Re: ILO stops working after switch is rebooted
my system management homepage doesnt have an option for ILO anywhere.
Maybe I have an old support pack installed or something. Also tried to install hponcfg but it complained that my support back is too old...so now I need to update that too I guess :(
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2006 05:18 AM
тАО07-07-2006 05:18 AM
Re: ILO stops working after switch is rebooted
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2006 05:44 AM
тАО07-07-2006 05:44 AM
Re: ILO stops working after switch is rebooted
Scott