- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Interrupt 15
ProLiant Servers (ML,DL,SL)
1778255
Members
1915
Online
109083
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2000 04:00 PM
тАО12-03-2000 04:00 PM
Interrupt 15
I have a Compaq Proliant 1600 running NetWare 5.0. This server also has a Adaptec 29160 scsi card installed. The adaptec card is taking interrupt 15. Interrupt 15 is one of 3 interrupts that NetWare reserves.
How can I change the interrupt that the Adaptec card is using?
How can I change the interrupt that the Adaptec card is using?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2000 04:00 PM
тАО12-03-2000 04:00 PM
Re: Interrupt 15
IRQ 15 should not be a problem running under Netware 5 .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2000 04:00 PM
тАО12-05-2000 04:00 PM
Re: Interrupt 15
* Reboot the server and press F10 when prompted to enter setup.
* Select System configuration, then Configure hardware
* Find the device you want to change the IRQ of in the device list
* Press F6 to change the resources it uses
Note:
To change the IRQ of a Smart controller you have to change the resources of the device BELOW it in the list (usually has a name of PCI device function 1). The reason for this is that the Smart controller is a bridged device.
RagS!
* Select System configuration, then Configure hardware
* Find the device you want to change the IRQ of in the device list
* Press F6 to change the resources it uses
Note:
To change the IRQ of a Smart controller you have to change the resources of the device BELOW it in the list (usually has a name of PCI device function 1). The reason for this is that the Smart controller is a bridged device.
RagS!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP