- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: R12000 UPS REPO Alarm
ProLiant Servers (ML,DL,SL)
1756305
Members
2801
Online
108844
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2010 10:40 AM
тАО01-06-2010 10:40 AM
R12000 UPS REPO Alarm
Our new used R12000 UPS shuts down after initial power up of electronic modules. There are two alarms: the bypass alarm, which is OK, and the Remote Emergency Power Off (REPO) alarm which is not OK, and I believe is the problem. It indicates that the UPS was powered off remotely. There is no remote switch hooked up. This unit is purely for testing batteries and electronics modules, so the only external connection is the power input. I've been researching how to disable this REPO error internally through the control panel but the manuals don't cover this. Any help would be appreciated.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2010 07:23 AM
тАО01-07-2010 07:23 AM
Re: R12000 UPS REPO Alarm
Hi, maybe there's something stuck in the port causing it to be triggered?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2010 09:09 AM
тАО01-07-2010 09:09 AM
Re: R12000 UPS REPO Alarm
Thank you for the reply. I was able to get rid of the REPO alarm. There are two wire terminals in rear of the R12000 where an emergency switch is supposed to be connected. We jumped the terminals with a wire and now the REPO error has disappeared, even when the wire is disconnected. It was probably a stuck relay. Thanks again, closing thread.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2010 09:13 AM
тАО01-07-2010 09:13 AM
Re: R12000 UPS REPO Alarm
I found the solution. It is stated in my reply to the first responder.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP