- Community Home
- >
- Servers and Operating Systems
- >
- Server Clustering
- >
- Re: Configuring HP including logical drives and ho...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-12-2020 01:18 AM - edited 11-13-2020 01:12 AM
11-12-2020 01:18 AM - edited 11-13-2020 01:12 AM
Configuring HP including logical drives and hosts
Settings are in general default unless specified My CC Pay
To create HP P2000 G3 Vdisks, select requirements as appropriate. In the GUI, select Configuration View > Logical > Vdisks. For example, if you create 4 + P RAID-5 arrays with a spare and 1:1 mapping to volumes, the system data is stripped across all the LUNs in the controller storage pool. For performance and robustness, much larger disk-member arrays (Vdisks) are not recommended.
The HP P2000 G3 LUNS are default volume-mapped to all ports on the controller. This mapping is useful if the controller is separately zoned only to the system nodes. Otherwise time consuming, individual mapping of each system port is required. The LUNS cannot be shared. Access must be limited to the system ports only.
To detect a controller, it might be necessary to run the svctask detectmdisk and svcinfo lsdiscoverystatus commands.
Select the standard host profile and FC host type. Disk spin-down is not supported as unresponsive disks can result in taking storage pools offline.
LUNs are exported through the available FC ports of the HP P2000 G3 storage system. Configure these LUNs as default mapping or explicit.
Special LUNsThere are no special considerations for logical unit numbering. LUN 0 can be exported where necessary.
Target portsA HP P2000 G3 storage system has a total of four 8 GB Fibre Channel ports.
- Tags:
- answer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-15-2020 09:37 PM
11-15-2020 09:37 PM
Re: Configuring HP including logical drives and hosts
Hello,
I did not understand, please explain what is exactly your query or what is your requirement.
I hope the below link helps you.
https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c05079929
https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c02520791
https://www.storagenetworks.com/documents/manuals/hp-p2000-user-manual.pdf
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
I am a HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]