- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: Strange ILO Problem on DL380G3
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-10-2006 03:03 AM
тАО02-10-2006 03:03 AM
Strange ILO Problem on DL380G3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-13-2006 05:26 PM
тАО02-13-2006 05:26 PM
Re: Strange ILO Problem on DL380G3
Here are 2 ways you can enable it ...
1. Switch the iLO Secutity override switch on the system board to "on". This overrides iLO security. (Remember to switch off the security override after iLO has been suitably configured)
2. If the system has a Linux or Windows OS running on it, then HP online configuration utility (HPONCFG) can be used to set the the value of "F8_PROMT_ENABLED" in iLO Global configuration to "Yes".
If the iLO is not responding on network, please re-check the network configuration of iLO using F8 menu in the POST or HPONCFG.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-13-2006 08:16 PM
тАО02-13-2006 08:16 PM
Re: Strange ILO Problem on DL380G3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-30-2006 12:21 AM
тАО03-30-2006 12:21 AM
Re: Strange ILO Problem on DL380G3
sometimes this kvm-switch or the display itself detects the video signal to slow so it won't display anything untill the video-signal is stable fore some time.
It also needs some time to switch when the display changes resolution (between PXE-boot and bios-config menu.
if this is so, blindly typeing F8 (repeatedly) when powering on the server before the display comes up may help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-31-2006 04:09 AM
тАО03-31-2006 04:09 AM
Re: Strange ILO Problem on DL380G3
I recommend flashing the firmware again-
1) unplug
2) set the iLO security jumper
3) boot the server to the Smartstart firmware maintenance CD
4) update the iLO firmware
5) shut down, power off, unplug, restore the security switch