- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: FC Tape Drives HPUX 11.0
StoreEver Tape Storage
1755398
Members
2898
Online
108832
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-11-2004 09:53 AM
тАО08-11-2004 09:53 AM
FC Tape Drives HPUX 11.0
Should a FC tape drive be displayed by ioscan? I only see fc and fcp but no tape drive listed under them.
I have installed QPK1100 and HWE1000 bundles. Also the HP A6795A fw revision and status LEDs on HP hub are ok.
When I send fcmsutil /dev/td0 get fabric I get a warning:
The Fabric parameters shown below might not be valid, since the HBA is not currently logged in with the Fabric.
Any assistance would be greatly appreciated.
Thanks!
I have installed QPK1100 and HWE1000 bundles. Also the HP A6795A fw revision and status LEDs on HP hub are ok.
When I send fcmsutil /dev/td0 get fabric I get a warning:
The Fabric parameters shown below might not be valid, since the HBA is not currently logged in with the Fabric.
Any assistance would be greatly appreciated.
Thanks!
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-11-2004 10:36 PM
тАО08-11-2004 10:36 PM
Re: FC Tape Drives HPUX 11.0
Hi,
FC tape driver must be displayed by
ioscan -fnC tape.
FC tape driver must be displayed by
ioscan -fnC tape.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-13-2004 02:55 AM
тАО08-13-2004 02:55 AM
Re: FC Tape Drives HPUX 11.0
run the command "ioscna -fn | grep -i unc" to see if any devices is unclaimed. If so you may need to install the driver for the tape drive (stape is used by HP drives)
since you are connecting to a hub this will be a loop config and you may want to check your tape drive to see if there is any config to state loop vs fabric (eg NL port vs N port)
since you are connecting to a hub this will be a loop config and you may want to check your tape drive to see if there is any config to state loop vs fabric (eg NL port vs N port)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-13-2004 03:17 AM
тАО08-13-2004 03:17 AM
Re: FC Tape Drives HPUX 11.0
SAN Canfigurtion problem.. your HBA is not being seen (or not logged in at your SAN switch)..
Get the out put of tdutil /dev/td0 (or fcmsutil /dev/td0) and give the output to your SAN folks so your HBA can be properly added to whatever zone your tapedrives are on..
Get the out put of tdutil /dev/td0 (or fcmsutil /dev/td0) and give the output to your SAN folks so your HBA can be properly added to whatever zone your tapedrives are on..
Hakuna Matata.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP