- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: HP 1/8 G2 Tape Autoloader Mechanical block 8C/...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-09-2021 03:00 AM
02-09-2021 03:00 AM
HP 1/8 G2 Tape Autoloader Mechanical block 8C/08
Good Day!
Any help after power cut or power off and my Autoloader is start running going to failed and after power on showing error code Mechanical Block Issue Code: 8c 08 any advise.
THnaks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-11-2021 06:52 AM - edited 02-11-2021 06:53 AM
02-11-2021 06:52 AM - edited 02-11-2021 06:53 AM
Re: HP 1/8 G2 Tape Autoloader Mechanical block 8C/08
Hi,
Power off.
Releasing the magazines manually
Check with a Light if there is something blocking the Gripper.
Maybe you need to remove also the Tapedrive.
Most times, a Tape is falling Inside.
See: HPE StoreEver 1/8 G2 Tape Autoloader User and Service Guide
From the back of the device, find the access holes for the right and left magazines.
1. Right magazine release access hole
2. Left magazine release access hole
The magazine release is a small latch.
3. Insert the end of a small metal pin or straightened paper clip into the magazine access hole at the back of
the autoloader about 1.5 cm (0.6 inch), while another person grasps the magazine on that side and pulls it
out of the front of the autoloader.
Cali
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-13-2021 03:34 AM
02-13-2021 03:34 AM
Re: HP 1/8 G2 Tape Autoloader Mechanical block 8C/08
Hello!
I tried that one now showing "MAGAZINE REMOVED" after 15 minutes shwoing "Robotic Stopped Error Code: B3 07 or "INSERT RIGHT MAGAZINE"
Please advise
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-13-2021 06:42 AM
02-13-2021 06:42 AM
Re: HP 1/8 G2 Tape Autoloader Mechanical block 8C/08
For Power On, Insert the Magazin again.