Re: Configure multicast over vlans

Mos007 · ‎02-03-2010

Hi,

I have 5412 switch and I need to configure the multicast to run over 3 vlans. I enabled the ip multicast routing.

Traffic still stay within the vlans, is there anything else I need to do?

I would like to hear anyone that can help me out with this asap.

thanks in advance!

Patrick Terlisten · ‎02-03-2010

Hello,

can you provide a "show running-config" of the 5412? Thanks.

Regards,
Patrick

Best regards,
Patrick

Mos007 · ‎02-03-2010

yes, here is it:

Running configuration:

; J8698A Configuration Editor; Created on release #K.14.47

hostname "ProCurve Switch 5412zl"
time timezone 2
module 1 type J8702A
module 2 type J8702A
module 3 type J8702A
module 4 type J8702A
module 5 type J8702A
module 6 type J8702A
module 7 type J8702A
module 8 type J8702A
module 9 type J8706A
module 12 type J8702A

ip default-gateway 10.10.13.254
ip routing
vlan 1
name "DEFAULT_VLAN"
no untagged A1-A24,B1-B24,C1-C24,D1-D24,E1-E24,F1-F24,G1-G24,H1-H24,I3-I24,L1-L24,Trk1
no ip address
exit
vlan 14
name "v14"
untagged B4,B6-B11,B14-B24,C1-C23,D1-D2,D4-D14,D16-D24,E1-E2,E4-E24,F1-F13,F15,F17,F19-F24,G1-G11,G13-G24,H1-H23,I22-I24
qos priority 3
ip helper-address 10.10.15.1
ip address 10.10.14.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B3,B5,B13,I3-I21,Trk1
jumbo
ip igmp
exit
vlan 15
name "v15"
untagged A1-A24,B1-B3,B5,B13,L13-L14
qos priority 5
ip address 10.10.15.254 255.255.255.0
tagged I3-I24
jumbo
ip igmp high-priority-forward
exit
vlan 16
name "v16"
untagged H24
qos priority 7
ip helper-address 10.10.15.1
ip address 10.10.16.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B24,C1-C24,D1-D24,E1-E24,F1-F24,G1-G24,H1-H23,I3-I21,L1-L24,Trk1
exit
vlan 13
name "v13"
untagged B12,C24,D3,D15,E3,F14,F16,F18,G12,L1-L12,L15-L23
qos priority 3
ip helper-address 10.10.15.1
ip address 10.10.13.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B3,B5,B13,I3-I24,Trk1
jumbo
ip igmp
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
qos protocol IP priority 7
qos protocol IPX priority 1
qos protocol ARP priority 6
qos protocol AppleTalk priority 0
qos protocol SNA priority 1
qos protocol NetBEUI priority 5
mirror 1 port A2
timesync sntp
sntp unicast
sntp server priority 1 10.10.15.1 3
web-management ssl
ip authorized-managers 10.10.15.239 255.255.255.255 access manager
ip timep manual 10.10.4.12
ip route 0.0.0.0 0.0.0.0 10.10.15.20
ip multicast-routing
interface A1
monitor all both mirror 1
exit
interface A3
monitor all both mirror 1
exit
interface A5
monitor all both mirror 1
exit
snmp-server community "xxx" operator
snmp-server community "xxx" operator unrestricted
primary-vlan 14

Patrick Terlisten · ‎02-03-2010

Hello,

try an "ip pim" in the VLANs, in which multicast traffic should be routed.

Could you post the output of "show ip igmp" and "show ip igmp config"?

Regards,
Patrick

Best regards,
Patrick

Mos007 · ‎02-03-2010

Patrick Terlisten · ‎02-03-2010

Hello,

just go into the vlan context and type

ip pim all

Regards,
Patrick

Best regards,
Patrick

Mos007 · ‎02-03-2010

I added the following to the setup but still no change. what am I doing wrong :(

ip multicast-routing
router rip
exit
router pim
exit
vlan 13
ip pim-dense
ip-addr 10.10.13.254
exit
exit
vlan 14
ip pim-dense
ip-addr 10.10.14.254
exit
exit
vlan 15
ip pim-dense
ip-addr 10.10.15.254
exit
exit

Jeff Carrell · ‎02-03-2010

in addition, each vlan you want multicast routing must also have a routing protocol (such as rip or ospf)...

so in your vlans you added 'ip pim' you also need 'ip rip' (since you have 'routing rip' enabled)...

hth..jeff

Mos007 · ‎02-03-2010

still not working ...

ProCurve Switch 5412zl# show running-config
Running configuration:

; J8698A Configuration Editor; Created on release #K.14.47

hostname "ProCurve Switch 5412zl"
time timezone 2
module 1 type J8702A
module 2 type J8702A
module 3 type J8702A
module 4 type J8702A
module 5 type J8702A
module 6 type J8702A
module 7 type J8702A
module 8 type J8702A
module 9 type J8706A
module 12 type J8702A

ip default-gateway 10.10.13.254
ip routing
vlan 1
name "DEFAULT_VLAN"
no untagged A1-A24,B1-B24,C1-C24,D1-D24,E1-E24,F1-F24,G1-G24,H1-H24,I3-I24,L1-L24,Trk1
no ip address
exit
vlan 14
untagged B4,B6-B11,B14-B24,C1-C23,D1-D2,D4-D14,D16-D24,E1-E2,E4-E24,F1-F13,F15,F17,F19-F24,G1-G11,G13-G24,H1-H23,I22-I24
qos priority 3
ip helper-address 10.10.15.1
ip address 10.10.14.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B3,B5,B13,I3-I21,Trk1
jumbo
ip igmp
exit
vlan 15
untagged A1-A24,B1-B3,B5,B13,L13-L14
qos priority 5
ip address 10.10.15.254 255.255.255.0
tagged I3-I24
jumbo
ip igmp high-priority-forward
exit
vlan 16
untagged H24
qos priority 7
ip helper-address 10.10.15.1
ip address 10.10.16.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B24,C1-C24,D1-D24,E1-E24,F1-F24,G1-G24,H1-H23,I3-I21,L1-L24,Trk1
exit
vlan 13
untagged B12,C24,D3,D15,E3,F14,F16,F18,G12,L1-L12,L15-L23
qos priority 3
ip helper-address 10.10.15.1
ip address 10.10.13.254 255.255.255.0
tagged A1-A14,A17-A24,B1-B3,B5,B13,I3-I24,Trk1
jumbo
ip igmp
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
qos protocol IP priority 7
qos protocol IPX priority 1
qos protocol ARP priority 6
qos protocol AppleTalk priority 0
qos protocol SNA priority 1
qos protocol NetBEUI priority 5
mirror 1 port A2
timesync sntp
sntp unicast
sntp server priority 1 10.10.15.1 3
web-management ssl
ip authorized-managers 10.10.15.239 255.255.255.255 access manager
ip timep manual 10.10.4.12
ip route 0.0.0.0 0.0.0.0 10.10.15.20
ip multicast-routing
router rip
exit
router pim
exit
interface A1
monitor all both mirror 1
exit
interface A3
monitor all both mirror 1
exit
interface A5
monitor all both mirror 1
exit
snmp-server community "xxx" operator
snmp-server community "xxx" operator unrestricted
spanning-tree Trk1 priority 4
vlan 13
ip rip 10.10.13.254
ip pim-dense
ip-addr any
exit
exit
vlan 14
ip rip 10.10.14.254
ip pim-dense
ip-addr any
exit
exit
vlan 15
ip rip 10.10.15.254
ip pim-dense
ip-addr any
exit
exit
primary-vlan 14

Patrick Terlisten · ‎02-04-2010

Hello,

what kind of application do you use?

Regards,
Patrick

Best regards,
Patrick

Mos007 · ‎02-04-2010

Hi Patrick,

I'm using the default MAC PRO bonjour protocol which working fine within the same vlan but does not working between vlans.

thanks,