- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: disable vrrp messages
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2007 08:35 PM
тАО04-02-2007 08:35 PM
We have 2 redundant routers connected each configured with vrrp.
The logs of one of them (procurve 5412zl) is filling up with these messages:
W 04/03/07 08:49:02 00783 vrrp: Pkt recd on a non-VRRP Vlan with vid 10
how can i disable this without disabling other warning messages(so only discard vrrp warning messages)
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2007 11:13 PM
тАО04-02-2007 11:13 PM
Re: disable vrrp messages
Configure Vlan10 on the Other VRRP switch and configure a Virtual Router for it and you won't get this message.
Unless you get these Event Log Messages on a Syslog server, Event logs can cleared but not disabled.
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2007 11:48 PM
тАО04-02-2007 11:48 PM
Re: disable vrrp messages
we have 2 firewalls which are configured to use vrrp for their vlan's and which are connected to 2 internal switches.
These 2 internal switches are also router for our internal networks and are configured with vrrp. i get these messages on the vlan's where the firewalls are connected on(and where the firewalls will do the vrrp).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2007 12:04 AM
тАО04-03-2007 12:04 AM
Re: disable vrrp messages
I suggest you block the VRRP messages from its source.
I believe with the firewalls you can block this kind of traffic, and it depends on the firewalls you have.
You can configure VRRP authentication for the messages on the Firewalls.
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2007 02:45 PM
тАО04-03-2007 02:45 PM
SolutionName: eventType
Type: OBJECT-TYPE
OID: 1.3.6.1.2.1.16.9.1.1.3
Full path: iso(1).org(3).dod(6).internet(1).mgmt(2).mib-2(1).rmon(16).event(9).eventTable(1).eventEntry(1).eventType(3)
Module: RMON-MIB
Parent: eventEntry
Prev sibling: eventDescription
Next sibling: eventCommunity
Numerical syntax: Integer (32 bit)
Base syntax: INTEGER
Composed syntax: INTEGER
Status: mandatory
Max access: read-write
Value list: 1: none(1)
2: log(2)
3: snmp-trap(3)
4: log-and-trap(4)
Description: The type of notification that the probe will make
about this event. In the case of log, an entry is
made in the log table for each event. In the case of
snmp-trap, an SNMP trap is sent to one or more
management stations.
The default is 4 (log-and-trap) you want to disable it which is 1.
5412(config)# setmib 1.3.6.1.2.1.16.9.1.1.3.783 -i 1
Don't forget to assign points to posts that were helpful to you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2007 05:18 PM
тАО04-03-2007 05:18 PM
Re: disable vrrp messages
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2007 06:04 PM
тАО04-03-2007 06:04 PM
Re: disable vrrp messages
the snmp stuff works great!
do you know where i can download the mib(instead of pulling it from the device itself) to use as a reference?
I also saw that the snmp "number" you mentioned was also in the log entry itself which was very helpfull.
thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2007 06:44 PM
тАО04-03-2007 06:44 PM
Re: disable vrrp messages
http://www.hp.com/rnd/software/MIBs.htm
From the MIB itself, the description is:
logDescription OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An implementation dependent description of the
event that activated this log entry."
So there is no list of all possible log types in the MIB file. The closest you can get to a list (that I know of) is with:
5412zl(config)# walkmib 1.3.6.1.2.1.16.9.2.1.4
Hope that helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2015 08:25 AM
тАО06-30-2015 08:25 AM
Re: disable vrrp messages
when i run this command it repeats the OID saying unable to create. Is there something else that needs to be done?