- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Layer 3 switching
Switches, Hubs, and Modems
1757739
Members
2149
Online
108863
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-11-2003 06:58 PM
тАО08-11-2003 06:58 PM
Layer 3 switching
Hi all
I am using 2 HP 5304 L3 switch & trying to configure OSPF routing .i need to know whether HP switch's support zero support,ifso what's the command to enable that.i tried my best it's not accepting.
I am using 2 HP 5304 L3 switch & trying to configure OSPF routing .i need to know whether HP switch's support zero support,ifso what's the command to enable that.i tried my best it's not accepting.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-11-2003 11:49 PM
тАО08-11-2003 11:49 PM
Re: Layer 3 switching
i think is
# conf t
ip subnet-zero
setting OSPF is like a cisco router!
# conf t
ip subnet-zero
setting OSPF is like a cisco router!
Teach is the best way to learn
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2003 02:56 AM
тАО08-12-2003 02:56 AM
Re: Layer 3 switching
Hi,
The IP Subnet Zero command applies to Cisco boxes or 93XX but not the 53XX. I just configured 10.10.10.1/9 (255.128.0.0) which is 1 Bit for Subnetting and the 53XX (E.07.30) accepts it. SO what range were you trying to configure? What was the error message?
Thanks, Ardon
The IP Subnet Zero command applies to Cisco boxes or 93XX but not the 53XX. I just configured 10.10.10.1/9 (255.128.0.0) which is 1 Bit for Subnetting and the 53XX (E.07.30) accepts it. SO what range were you trying to configure? What was the error message?
Thanks, Ardon
ProCurve Networking Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-13-2003 04:29 AM
тАО08-13-2003 04:29 AM
Re: Layer 3 switching
IP-subnet zero ,i tried already but it's not picking up.even i upgraded the flash to the latest version E_07_30.
Is it advisable to use zero subnet?
Is it advisable to use zero subnet?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP