- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Procurve 2824 not showing IP address
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-27-2010 06:51 AM
04-27-2010 06:51 AM
Procurve 2824 not showing IP address
Thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-08-2010 06:39 PM
06-08-2010 06:39 PM
Re: Procurve 2824 not showing IP address
switch1# show arp
you can also show the mac address with the associated port number
switch1# show mac
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-09-2010 05:21 AM
06-09-2010 05:21 AM
Re: Procurve 2824 not showing IP address
I am not sure where to enter switch1# statement
Also, do I enter switch1
Please elaborate.
Thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-09-2010 06:17 AM
06-09-2010 06:17 AM
Re: Procurve 2824 not showing IP address
You do not apply ip addresses directly to a port as you would a firewall or a router.
You apply the ip address to the vlan interface so if your switch only has its default configuration you would have only one vlan and you would do the following at the CLI.
Enter configuration mode and type:
vlan 1
ip address x.x.x.x 255.255.255.0
exit
You should then be able to access the switch via the IP address.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-09-2010 07:01 AM
06-09-2010 07:01 AM
Re: Procurve 2824 not showing IP address
I am a noob at this and still learning so please bear with me.
OK. Went to the CLI and checked out the VLan settings but did not understand it. At the command prompt, I entered vlan 1 and it said that it is an 'invalid input'.
I checked that the VLAN ID is 1, name is DEFAULT_VLAN, VLan type is Static and the ports are untagged.
Now the question is what do I enter in the CLI?
Thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-09-2010 07:14 AM
06-09-2010 07:14 AM
Re: Procurve 2824 not showing IP address
However, in response to your last post you would need to be in configuration mode for the command â vlan 1â to work to enter configuration mode type â configure terminalâ or â conf tâ . If you do change vlan 1â s ip address this will be the IP address you use to connect to your switch so if you already have an ip address set for remote access then I would leave it alone (unless itâ s not correct).
To determine If you vlan 1 (default_vlan) already has an ip address you can just use the â show runâ command and you should see if listed as below:
Vlan 1
Default_vlan
Untagged 1-24
Ip address x.x.x.x 255.255.255.0
Exit
That being saidâ ¦What I think you are asking and what brakern19 already answered was how do I find out what device IP addresses (e.g computer, printer, server) are connected to each of your switch ports?
You should be able to enter the "show arp" command at either of the following prompts
switchname#
switchname(config)#
So for example:
switchname# ping 192.168.1.X (for each of the ip addresses in your network)
Then you can run the â show arpâ like this:
switchname#show arp
It should then show a list of the IP addresses and the corresponding ports the switch used to reach the end device.
Please ensure you give points to brakerm19 and not myself as he has the correct answer Iâ m just elaborating.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-09-2010 07:23 AM
06-09-2010 07:23 AM
Re: Procurve 2824 not showing IP address
Sorry I should have read your original post more carefully I don't think my first post concerns what you are trying to accomplish it shows how to apply an IP address to your switch so you can reach it.
However, in response to your last post you would need to be in configuration mode for the command "vlan 1" to work to enter configuration mode type "configure terminal" or "conf t". If you do change vlan's ip address this will be the IP address you use to connect to your switch so if you already have an ip address set for remote access then I would leave it alone (unless it's not correct).
To determine If you vlan 1 (default_vlan) already has an ip address you can just use the "show run" command and you should see if listed as below:
Vlan 1
Default_vlan
Untagged 1-24
Ip address x.x.x.x 255.255.255.0
Exit
That being said...What I think you are asking and what brakern19 already answered was how do I find out what device IP addresses (e.g computer, printer, server) are connected to each of your switch ports?
You should be able to enter the "show arp" command at either of the following prompts
switchname#
switchname(config)#
So for example:
switchname# ping 192.168.1.X (for each of the ip addresses in your network)
Then you can run the "how arp" like this:
switchname#show arp
It should then show a list of the IP addresses and the corresponding ports the switch used to reach the end device.
Please ensure you give points to brakerm19 and not myself as he has the correct answer I'm just elaborating.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-10-2010 03:34 PM
06-10-2010 03:34 PM
Re: Procurve 2824 not showing IP address
OR
Are you trying to find the IP address of a client device connected to the switch?
the 'switch1#' is the CLI prompt. this is not a command you type.
at the CLI prompt (switchname#)
type: show management
This will show all address assigned to the switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-11-2010 05:15 AM
06-11-2010 05:15 AM
Re: Procurve 2824 not showing IP address
I know the IP address of the switch but when I go to web interface or when I telnet to the switch, I cannot see the ip addresses of the devices connected to the ports of that switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-11-2010 05:24 AM
06-11-2010 05:24 AM
Re: Procurve 2824 not showing IP address
Have you been able to get the "show arp" command to work yet?