Comware Based
1747980 Members
3925 Online
108756 Solutions
New Discussion юеВ

Re: Web Management with A5120-EI Series Switches available?

 
SOLVED
Go to solution
Manfred M.
Advisor

Web Management with A5120-EI Series Switches available?

I'm using FW Release HP A5120EI-CMW520-R2208.

 

Is the Web Management over http with this FW release available?

How do I configure the access - what "service-type" do I have to configure?

Where do I find the documentation for Web Management?

 

I'm just getting a nice Login-Page...

 

With kind regards

Manfred

10 REPLIES 10
Manfred M.
Advisor
Solution

Re: Web Management with A5120-EI Series Switches available?

Just had to read the RIGHT Manual on the RIGHT Website (H3C)....

 

The only thing I have forgotten to configure was:

authorization-attribute level 3

 

The service-type is telnet.

 

I found the description for configuring the Web interface in the H3C S5120-EI Series Ethernet Switches
Fundamentals Configuration Guide: http://www.h3c.com.hk/Technical_Support___Documents/Technical_Documents/Switches/H3C_S5120_Series_Switches/Configuration/Operation_Manual/H3C_S5120-EI_CG-Release_2210-6W100/01/ on page 61 (Chapter: Web login).

 

Configuration example for http access:
 
# Log in to the device via the console port and configure the IP address of VLAN 1 of the device. VLAN
1 is the default VLAN. 
<Sysname> system-view
[Sysname] interface vlan-interface 1
[Sysname-VLAN-interface1] ip address 192.168.0.58 255.255.255.0
[Sysname-VLAN-interface1] quit
# Create a local user named admin, and set the password to admin for the user. Specify the telnet service
type for the local user, and set the command level to 3 for this user. 
[Sysname] local-user admin
[Sysname-luser-admin] service-type telnet 
[Sysname-luser-admin] authorization-attribute level 3
[Sysname-luser-admin] password simple admin

 

That easy? YES!

 

P.S.:

Maybe you will have to activate the http service if it's not enabled by default:

[Sysname]ip http enable

 

Manfred

 

 

 

 

gerooo
Occasional Visitor

Re: Web Management with A5120-EI Series Switches available?

hello,

 

i have do the same thing, but i got this when i go to the http interface :

HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 en ab010000 Save Help Logout User has no privilege. Are you sure to save the current configuration? HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 ie 0 0 admin admin 3 

 if you have an answer, i will very happy.

 

thanks

pnikies
New Member

Re: Web Management with A5120-EI Series Switches available?

use firefox

Justic
New Member

Re: Web Management with A5120-EI Series Switches available?

Security Logging Disabled
vplascencia
New Member

Re: Web Management with A5120-EI Series Switches available?

are there a web mangement manual?

BMNetworks
Occasional Advisor

Re: Web Management with A5120-EI Series Switches available?

I have the same problem. How can I resolve this issue? With firefox it work but most customers does only use IE

Apachez-
Trusted Contributor

Re: Web Management with A5120-EI Series Switches available?

I think the user you wish to use must have the following service-type defined:

 

service-type web

 

And make sure you have "ip http enable" in the config (if you wish to use unencrypted http webgui):

 

display current-configuration | begin http

 

naive
Occasional Visitor

Re: Web Management with A5120-EI Series Switches available?

I have an HPE 5120 series switch, i have enabled http login via console terminal, whenever i login via web ( ie) , i am required to enter "verify code" besides the username and the password, how do i get the "verify code" , the manuals dont speak anything of "verify code" except to fill that info when prompted. Any help would be appreciated .

Thanks!

parnassus
Honored Contributor

Re: Web Management with A5120-EI Series Switches available?

The Verify Code should be clearly visible on the same Login Page (it's a sort of Captcha) and it's (re)generated every time by the Switch in order to complete the login procedure on that page.

Probably you should use a different Web Browser (like Mozilla Firefox, as example) other than the one you're currently using (Microsoft Internet Explorer) to verify that that Web Browser is able to show it correctly.


I'm not an HPE Employee
Kudos and Accepted Solution banner