Web Management with A5120-EI Series Switches available?

[Manfred M.]

I'm using FW Release HP A5120EI-CMW520-R2208.

Is the Web Management over http with this FW release available?

How do I configure the access - what "service-type" do I have to configure?

Where do I find the documentation for Web Management?

I'm just getting a nice Login-Page...

With kind regards

Manfred

[Manfred M. · Accepted solution]

Just had to read the RIGHT Manual on the RIGHT Website (H3C)....

The only thing I have forgotten to configure was:

authorization-attribute level 3

The service-type is telnet.

I found the description for configuring the Web interface in the H3C S5120-EI Series Ethernet Switches
Fundamentals Configuration Guide: http://www.h3c.com.hk/Technical_Support___Documents/Technical_Documents/Switches/H3C_S5120_Series_Switches/Configuration/Operation_Manual/H3C_S5120-EI_CG-Release_2210-6W100/01/ on page 61 (Chapter: Web login).

Configuration example for http access:
 
# Log in to the device via the console port and configure the IP address of VLAN 1 of the device. VLAN
1 is the default VLAN. 
<Sysname> system-view
[Sysname] interface vlan-interface 1
[Sysname-VLAN-interface1] ip address 192.168.0.58 255.255.255.0
[Sysname-VLAN-interface1] quit
# Create a local user named admin, and set the password to admin for the user. Specify the telnet service
type for the local user, and set the command level to 3 for this user. 
[Sysname] local-user admin
[Sysname-luser-admin] service-type telnet 
[Sysname-luser-admin] authorization-attribute level 3
[Sysname-luser-admin] password simple admin

That easy? YES!

P.S.:

Maybe you will have to activate the http service if it's not enabled by default:

[Sysname]ip http enable

Manfred

[gerooo]

hello,

i have do the same thing, but i got this when i go to the http interface :

HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 en ab010000 Save Help Logout User has no privilege. Are you sure to save the current configuration? HP A5120-24G-PoE+ EI Switch with 2 Interface Slots Software Version 5.20 ie 0 0 admin admin 3 

 if you have an answer, i will very happy.

thanks

[pnikies]

use firefox

[Justic]

Security Logging Disabled

[vplascencia]

are there a web mangement manual?

[BMNetworks]

I have the same problem. How can I resolve this issue? With firefox it work but most customers does only use IE

[Apachez-]

I think the user you wish to use must have the following service-type defined:

service-type web

And make sure you have "ip http enable" in the config (if you wish to use unencrypted http webgui):

display current-configuration | begin http

[naive]

I have an HPE 5120 series switch, i have enabled http login via console terminal, whenever i login via web ( ie) , i am required to enter "verify code" besides the username and the password, how do i get the "verify code" , the manuals dont speak anything of "verify code" except to fill that info when prompted. Any help would be appreciated .

Thanks!

[parnassus]

The Verify Code should be clearly visible on the same Login Page (it's a sort of Captcha) and it's (re)generated every time by the Switch in order to complete the login procedure on that page.

Probably you should use a different Web Browser (like Mozilla Firefox, as example) other than the one you're currently using (Microsoft Internet Explorer) to verify that that Web Browser is able to show it correctly.

[CarlyML587]

Hello.

For the web interface administration follow the next configuration.

[Sysname] local-user admin
[Sysname-luser-admin]service-type ?
ftp FTP service type
lan-access LAN-ACCESS service type
portal Portal service type
ssh Secure Shell service type
telnet TELNET service type
terminal TERMINAL service type
web Web service type
[Sysname-luser-admin] service-type ssh
[Sysname-luser-admin] service-type telent
[Sysname-luser-admin] service-type web
[Sysname-luser-admin] authorization-attribute level 3
[Sysname-luser-admin] password simple admin
[Sysname] ip http enable
Info: HTTP server has been started!

[Sysname] dis cur
#
telnet server enable
#
local-user admin
password cipher $c$3$555f45546ZcXOPW16Z
authorization-attribute level 3
service-type ssh telnet
service-type web
#
ssh server enable
#
ip https enable
#

In your browser type the IP of the device 192.168.0.58 and introduce the data in the field blank and the code to login.

Regards.