- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Change single controller MSA500 G2
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2009 07:13 AM
тАО02-02-2009 07:13 AM
Change single controller MSA500 G2
Just to check. When i wanted to change a controller MSA500 G2 (Single), i need to power of the MSA and the servers connected to it.
Remove the damage controller and replace it with the new one. Also I need to replace the battery cache of the damage to the new.
there its something else i need to do?
Best regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2009 08:35 AM
тАО02-02-2009 08:35 AM
Re: Change single controller MSA500 G2
best to check through the maint manual here :-
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00172836/c00172836.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2009 08:36 AM
тАО02-02-2009 08:36 AM
Re: Change single controller MSA500 G2
i will
tks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-26-2014 06:14 AM
тАО11-26-2014 06:14 AM
Re: Change single controller MSA500 G2
HI
I want to replace one of the two redundant controllers.
Can I remove it during operation of the system?
I found the description of the HP StorageWorks Modular Smart Array500 Generation 2 Storage System Maintenance and Service Guide:
to remove redundant conntroler:
1.Determine if the controller configuration supports hot-plug cache replacement:
тИТ
If the storage system is equipped with a single controller, power down the storage system (on page9).
тИТ
If the system has redundant controllers and the replacement cache is a different capacity than the failed cache, power down the storage system (on page9).
тИТ
If the system has redundant controllers and the replacement cache is the same capacity as the failed cache, proceed with step 2.
2.Remove the controller ("Modular Smart Array 500 Generation 2 Controller" on page 13).
3.Remove the existing cache module.
Repeat steps 2 and 3 if the storage system has redundant controllers and the
replacement cache is a different capacity than the failed cache.
To replace the cache module:
1.Install the module in the slot....
Thanks and regards
Przemyslaw