3PAR Node rescue and Node SPI Image

[555-denoh]

I tested 3PAR7200 Node rescue.
　Test environment:　3PAR OS 3.2.2MU4
　Node1 SPI:　SPI Image 4.8.38. Release version. 16:57:04 Jul 17 2015.

I replaced Node0 with a SPI Image 1.2.9 node.
It stopped with the following error.

+-----------------------------------------------------------------------------+
HP SPI Image 1.2.9. Release version. 10:55:06 Nov 16 2012.
+-----------------------------------------------------------------------------+
Booting from device 0, AHCI0Invalid boot sector.
Use "boot net install" to correct this.

*** Fatal error: Code 39, sub-code 0x10 (0).
AHCI0 MBR does not have a valid partition table
Disabled FSBC boot watchdog.

*** Fatal error: Code 39, sub-code 0x10 (0).
*** Fatal error: Code 39, sub-code 0x10 (0).
Disabled FSBC boot watchdog.

Whack>

However, when I put a SPI Image 4.8.38 Node into Node0, the node rescue completed successfully.

Isn't SPI Image 1.2.9. Node built into SPI Image 4.8.38 Node?
Can SPI Image 1.2.9. Node use 3PAROS 3.2.2?
We don't know which SPI Image can support which 3PAR OS.
Is there a support matrix for SPI Image and 3PAR OS?

＝＝＝＝＝＝The following is a long work log.＝＝＝＝＝＝＝＝＝
Whack>
Whack>ide erase
ide commands unsupported on Sandy Bridge platforms
passing command to ahci...
Warning!! Security erase can take over an hour
Erase all AHCI0 drive data -- Are you sure? (Y/N) Yes
Erasing
.　　　　　=>***I'm only bothered by the display of "."
Whack>reset
Resetting...
Trapped IO 0xcf9 write of 0xa
Rebooting due to IO 0xcf9 write of 0xe
Board ID = BoardIdEOSNode 
EOS SAS Buffers Initialization Complete.
Loading PEIM at 0x000FFFD85A0 PeiVariable.efi
<part omitted>

Loading driver at 0x0007FBC1000 CBiosSmm.efi
Current Date and Time:  2024-08-20 01:55:57 (UTC-4)

HP SPI Image 1.2.9.  Release version. 10:55:06 Nov 16 2012.

Bootstrap CPU0
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3
      SKU Info: Max Frequency Ratio 18, Max Core Count 6
      CPU speed: 1800.00 MHz
      Bus speed:  100.00 MHz
      Bus to CPU ratio: 1/18

<part omitted>
]
    eth1 loopback Random pattern:         PASS
--> Starting: [21] Verify PCI Configuration
--> Starting: [22] Mass Storage Initialization
--> Starting: [23] Mass Storage Drive Test
    AHCI: skipping register test
    AHCI: skipping controller test
    AHCI0 seek test:                      PASS
    AHCI0 read test:                      PASS
    AHCI: skipping DMA read test
    First sector is blank.
--> Starting: [24] BIOS Automatic Update
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
--> Starting: [25] Fibre HBA Automatic Update
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
--> Starting: [26] Cluster Manager Reset
--> Starting: [27] Cluster Memory Initialization
Harrier ASIC found at 5.0.0.  CSR at 0xc0000000
Set0 DC DIMM 0.0.0 (J0300): Part #18HVF25672PZ-80EH1  SN:**removed**
Set0 DC DIMM 0.1.0 (J0301): Part #18HVF25672PZ-80EH1  SN:**removed** SPD Passed
Initializing Harrier at 5.0.0...
CSR=00:c0000000  SMW=00:a0000000  LMW=10:00000000  MMW=08:00000000
Running BIST Test: [GOOD]
CMA1: LPC1 is not Up, Trying LPC0
DMA PM using LPC2   CMA0 using LPC0  CMA1 using LPC0
RPC PM using LPC2   CMA0 using LPC0  CMA1 using LPC0
Set0 DC DIMM 0.0.0 (J0300): 2048 MB  CL4/6
Set0 DC DIMM 0.1.0 (J0301): 2048 MB  CL4/6
Present 1 Set 0, Side 0 Base = 00:00000000 Size = 00:ffffffff
Testing CMA interrupts: [............................]
Zero    32M cluster memory window: [                ]................]
Zero  4096M cluster memory window: [                               ]...............................]
Scan cluster memory for errors:    [                                ]................................]
CMA0 Cluster Memory is configured: 4096 MB CL4
Total Cluster Memory configured: 4096 MB
Harrier LPC Port Test: [............]
--> Starting: [28] Cluster Memory Diagnostic
test_list = 000136ff
    Testing CMA0 SMW data lines with walking 1
    Testing CMA0 SMW data lines with walking 0
    Testing CMA0 MMW data lines with walking 1
    Testing CMA0 MMW data lines with walking 0
    Testing CMA0 SMW ECC  lines with walking 1, channel 0
    Testing CMA0 SMW ECC  lines with walking 1, channel 1
    Testing CMA0 SMW ECC  lines with walking 0, channel 0
    Testing CMA0 SMW ECC  lines with walking 0, channel 1
    Testing CMA0 Opcode:  Zero ECC XOR PAR OR CRC
    Testing CMA0 SRC Interrupts CM->CM PM->CM CM->PM PM->PM 
    Testing CMA0 SMW address lines with walking 1
    Testing CMA0 SMW address lines with walking 0
Disabled FSBC boot watchdog.

Whack>
Whack>set perm cnt_no_os_boot=0
Whack>set perm cnt_no_cluster=0
Whack>set perm cnt_no_shutdown=0
Whack>set perm cnt_os_panic=0
Whack>set perm cnt_same_fatal=0
Whack>set perm cnt_log_error=0
Whack>set perm sys_serial=**removed**
Whack>eth dev 0
Selected ethernet device 0 at Memory c0600000
Whack>net addr 169.254.172.229
My address is 169.254.172.229
Whack>net netmask 0.0.0.16
Network mask 0.0.0.16
Whack>net gateway 192.168.40.72
Gateway address 192.168.40.72
Whack>net server 192.168.40.72
Server address 192.168.40.72
Whack>boot net install cr=3 ipaddr=169.254.172.229 nm=255.255.0.0 rp=192.168.40.72::rescue hn=1613873_0 eth=eth0
    Testing CMA0 MMW address lines with walking 1 (first 4 GB only)
    Testing CMA0 MMW address lines with walking 0 (first 4 GB only)
    Testing CMA0 with random XOR (all Cluster Memory)
4095 MB [                                                  ]..................................................]
--> Skipping: [29] Cluster PCI Diagnostic
--> Starting: [30] DIMM Information Collection
--> Skipping: [31] Manufacturing Centerpanel GPIO Test
--> Skipping: [32] Serial Port Loopback Test
--> Skipping: [33] Manufacturing Serial Port Test
--> Starting: [34] Environmental Initialization
--> Skipping: [35] Environmental Temperature and Voltage Test
--> Skipping: [36] Test CPU Operation
--> Skipping: [37] Manufacturing Cluster Link Initialization
--> Skipping: [38] Manufacturing Cluster Link Test
--> Skipping: [39] PCI Fibre Channel/SAS Adapter Test
--> Skipping: [40] PCI iSCSI Adapter Test
--> Starting: [41] System Error Reporting Init
--> Skipping: [43] Manufacturing CP EEPROM Test
--> Skipping: [44] Certify OS Startup
--> Skipping: [45] Table Execution Summary
+-----------------------------------------------------------------------------+
HP SPI Image 1.2.9.  Release version. 10:55:06 Nov 16 2012.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Pair0 DIMM0  (J0155): 8192 MB  CL5/10
|  Data Cache Size         4 GB  CL4/6
|                          Set0 DC DIMM 0.0.0 (J0300): 2048 MB  CL4/6
|                          Set0 DC DIMM 0.1.0 (J0301): 2048 MB  CL4/6
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk SSD U100 64GB     123612401529        64 GB
|  PCI Slot 0              LSI-SAS 9205-8e    
|  PCI Slot 1              Emulex  LPe12002          VM80175440          2-port
|  Board 920-200040.A5     FXN 2013/02/Wed 00139547  84:34:97:66:04:04
|  Cluster serial          1613873                   84:34:97:66:04:05
|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 01:56:54 (UTC-4)
+-----------------------------------------------------------------------------+
Booting from net...
    TFTP "install" from 192.168.40.72.............................................................................................................................................................................................................................................................................................complete

Setting FSB WDT Boot Complete State.
    CPU 0 [0] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core CountRebooting due to IO 0xcf9 write of 0x6
Board ID = BoardIdEOSNode 
EOS SAS Buffers Initialization Complete.
Loading PEIM at 0x000FFFD85A0 PeiVariable.efi
Loading PEIM at 0x000FFFD9CA0 ReadOnlyVariableOnReadOnlyVariable2Thunk.efi
Loading PEIM at 0x000FFFCD720 PchInitPeim.efi
<part omitted>

Loading driver at 0x0007FBC1000 CBiosSmm.efi
Current Date and Time:  2024-08-20 01:57:26 (UTC-4)

HP SPI Image 1.2.9.  Release version. 10:55:06 Nov 16 2012.

Bootstrap CPU0
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3
      SKU Info: Max Frequency Ratio 18, Max Core Count 6
      CPU speed: 1800.00 MHz
      Bus speed:  100.00 MHz
      Bus to CPU ratio: 1/18

Board reset reason: PCI_RESET
Previous reason   : PCI_RESET

--> Starting: [0] CPU Interrupt Vector Initialization
--> Starting: [1] CPU SDRAM Memory Scan
--> Starting: [2] PCI Bus Initialization
--------- Starting PCI scan #2:

  00.00.00 SandyBridge DMI2:
           Vendor Intel, Device 0x3c00, Rev 0x07
           Host/PCI bridge - Intel Device
  00.01.00 SandyBridge PCIe Root Port 1a:
           Vendor Intel, Device 0x3c02, Rev 0x07
           PCI/PCI bridge, bus 01-07
      01.00.00 PEX8648 #0:
               Vendor PLX, Device 0x8648, Rev 0xbb
               PCI/PCI bridge, bus 02-07
          02.01.00 PEX8648 #0 DS1 (slot 2):
                   Vendor PLX, Device 0x8648, Rev 0xbb
                   PCI/PCI bridge, bus 03
          02.04.00 PEX8648 #0 DS4:
                   Vendor PLX, Device 0x8648, Rev 0xbb
                   PCI/PCI bridge, bus 04
              04.00.00 Harrier LPC2:
                       Vendor 3PAR, Device 0x0003, Rev 0x00
                       Large  Memory Window 1 at 20:00000000
                       Disk cache controller
          02.05.00 PEX8648 #0 DS5:
                   Vendor PLX, Device 0x8648, Rev 0xbb
                   PCI/PCI bridge, bus 05
              05.00.00 Harrier LPC0:
                       Vendor 3PAR, Device 0x0003, Rev 0x00
                       Small  Memory Window 1 at    a0000000
                       Large  Memory Window 1 at 10:00000000
                       Medium Memory Window 1 at 08:00000000
                       Disk cache controller
          02.08.00 PEX8648 #0 DS8:
                   Vendor PLX, Device 0x8648, Rev 0xbb
                   PCI/PCI bridge, bus 06
              06.00.00 Slot 0:
                       Vendor LSI, Device 0x0087, Rev 0x01
                       SAS mass storage controller
          02.09.00 PEX8648 #0 DS9:
                   Vendor PLX, Device 0x8648, Rev 0xbb
                   PCI/PCI bridge, bus 07
              07.00.00 Slot 1:
                       Vendor Emulex, Device 0xf100, Rev 0x03
                       Fibre Channel controller
              07.00.01 Slot 1:
                       Vendor Emulex, Device 0xf100, Rev 0x03
                       Fibre Channel controller
  00.01.01 SandyBridge PCIe Root Port 1b:
           Vendor Intel, Device 0x3c03, Rev 0x07
           PCI/PCI bridge, bus 08
  00.03.00 SandyBridge PCIe Root Port 3a:
           Vendor Intel, Device 0x3c08, Rev 0x07
           PCI/PCI bridge, bus 09
  00.03.01 SandyBridge PCIe Root Port 3b:
           Vendor Intel, Device 0x3c09, Rev 0x07
           PCI/PCI bridge, bus 0a
  00.03.02 SandyBridge PCIe Root Port 3c:
           Vendor Intel, Device 0x3c0a, Rev 0x07
           PCI/PCI bridge, bus 0b
  00.03.03 SandyBridge PCIe Root Port 3d:
           Vendor Intel, Device 0x3c0b, Rev 0x07
           PCI/PCI bridge, bus 0c
  00.04.00 SandyBridge DMA Engine CH0:
           Vendor Intel, Device 0x3c20, Rev 0x07
           Base system controller
  00.04.01 SandyBridge DMA Engine CH1:
           Vendor Intel, Device 0x3c21, Rev 0x07
           Base system controller
  00.04.02 SandyBridge DMA Engine CH2:
           Vendor Intel, Device 0x3c22, Rev 0x07
           Base system controller
  00.04.03 SandyBridge DMA Engine CH3:
           Vendor Intel, Device 0x3c23, Rev 0x07
           Base system controller
  00.04.04 SandyBridge DMA Engine CH4:
           Vendor Intel, Device 0x3c24, Rev 0x07
           Base system controller
  00.04.05 SandyBridge DMA Engine CH5:
           Vendor Intel, Device 0x3c25, Rev 0x07
           Base system controller
  00.04.06 SandyBridge DMA Engine CH6:
           Vendor Intel, Device 0x3c26, Rev 0x07
           Base system controller
  00.04.07 SandyBridge DMA Engine CH7:
           Vendor Intel, Device 0x3c27, Rev 0x07
           Base system controller
  00.05.00 SandyBridge Memory Map/VTd:
           Vendor Intel, Device 0x3c28, Rev 0x07
           Base system controller
  00.05.02 SandyBridge RAS:
           Vendor Intel, Device 0x3c2a, Rev 0x07
           Base system controller
  00.05.04 SandyBridge IOAPIC:
           Vendor Intel, Device 0x3c2c, Rev 0x07
           Base system controller
  00.11.00 PCH Virtual Root Port:
           Vendor Intel, Device 0x1d3e, Rev 0x06
           PCI/PCI bridge, bus 0d
  00.1c.00 PCH PCI Express Port 1:
           Vendor Intel, Device 0x1d10, Rev 0xb6
           PCI/PCI bridge, bus 0e
  00.1c.06 PCH PCI Express Port 7:
           Vendor Intel, Device 0x1d1c, Rev 0xb6
           PCI/PCI bridge, bus 0f
      0f.00.00 Intel 82574 #0:
               Vendor Intel, Device 0x10d3, Rev 0x00
               Ethernet network controller
  00.1c.07 PCH PCI Express Port 8:
           Vendor Intel, Device 0x244e, Rev 0xb6
           PCI/PCI bridge, bus 10
      10.00.00 Intel 82574 #1:
               Vendor Intel, Device 0x10d3, Rev 0x00
               Ethernet network controller
  00.1e.00 PCH DMI to PCI Bridge:
           Vendor Intel, Device 0x1d25, Rev 0xa6
           PCI/PCI bridge, bus 11
  00.1f.00 PCH LPC:
           Vendor Intel, Device 0x1d41, Rev 0x06
           PCI/ISA bridge
  00.1f.02 PCH SATA:
           Vendor Intel, Device 0x1d02, Rev 0x06
           SATA mass storage controller
  00.1f.03 PCH SMBus:
           Vendor Intel, Device 0x1d22, Rev 0x06
           System Management Bus controller
  16-bit I/O space:               [       1000 ..        503f]
  32-bit prefetchable memory:     [          (none)          ]
  32-bit non-prefetchable memory: [   90000000 ..    c07fffff]
  64-bit prefetchable memory:     [10:00000000 .. 2f:ffffffff]
  36-bit prefetchable memory:     [08:00000000 .. 0b:ffffffff]

PCI bus scan and allocation completed in 2 passes.

PCIe  1.0.0: Serial EEPROM contents verified.
--> Starting: [3] Serial Port Initialization
--> Starting: [4] Remote Console Initialization
--> Starting: [5] Random Number Generator Init
--> Starting: [6] CPU SDRAM Memory Test
--> Starting: [7] Process NVRAM values
    Prior reset 2024-08-20 01:45:50
    Last reset  2024-08-20 01:55:43
    This reset  2024-08-20 01:57:11
    Time now    2024-08-20 01:57:29
--> Starting: [9] CPU APIC Initialization
    CPU 0 [0] Microcode check...
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
      CPU speed: 1800.00 MHz
      Bus speed:  100.00 MHz
      Bus to CPU ratio: 1/18
    CPU 0 [0] Done

    CPU 1 [1] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU 1 [1] shutting down.

    CPU 2 [2] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU 2 [2] shutting down.

    CPU 9 [9] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU 9 [9] shutting down.

    CPU b [b] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU b [b] shutting down.

    CPU 3 [3] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU 3 [3] shutting down.

    CPU 8 [8] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU 8 [8] shutting down.

    CPU a [a] starting up.
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3

      SKU Info: Max Frequency Ratio 18, Max Core Count 6
    CPU a [a] shutting down.

    Programming PCI interrupt lines
    APIC INT Vend.Dev Bus.Dev.Func Slot INT  AIRQ Vec ind  MSI
    0    02                        MB        2    ee  10
    0    03                        MB        3    7a  18
    0    04                        MB        4    7b  20
    0    08                        MB        8    7c  40
    0    09                        MB        9    75  48
    0    0d                        MB        13   7e  68
    0    0e                        MB        14   76  70
    0    0f                        MB        15   77  78
    0    11  8086.1d02  0.1f.2     MB    B   17   90  88
    0    12                        MB        18   7d  90
    0    16                        MB        22   78  b0
    0    17                        MB        23   79  b8
    1    00  1000.0087  6.0.0      0     A   24   30  00   0x00 -> 0xfec01020
    1    01  10df.f100  7.0.0      1     A   25   31  08   0x01 -> 0xfec01020
    1    0a  10df.f100  7.0.1      1     B   34   32  50   0x0a -> 0xfec01020
    1    10  1590.0003  5.0.0      MB    A   40   c0  80   0x10 -> 0xfec01020
    1    14  1590.0003  4.0.0      MB    A   44   c4  a0   0x14 -> 0xfec01020
    1    16  8086.10d3  f.0.0      MB    A   46   91  b0   0x16 -> 0xfec01020
    1    17  8086.10d3 10.0.0      MB    A   47   92  b8   0x17 -> 0xfec01020
    Timer Interrupt test:                 PASS
--> Starting: [10] CPU SDRAM ECC Initialization
--> Starting: [11] Board GPIO Init
--> Starting: [12] Node Fan Test
--> Starting: [14] Power Supply and Battery Init
--> Starting: [15] Power Supply and Battery Test
--> Starting: [16] PROM Checksum Test
    PROM checksum:                        PASS
--> Starting: [17] Ethernet PROM Test
    eth0 PROM contents:                   PASS
    eth0 PROM checksum:                   PASS
    eth1 PROM contents:                   PASS
    eth1 PROM checksum:                   PASS
--> Starting: [18] Real Time Clock Test
--> Starting: [19] Board GPIO Test
    FPGA Scratchpad Test [    ]....]           PASS
    NEMOE Loopback Test [          ]..........]      PASS
--> Starting: [20] Ethernet Loopback Test
    eth0 device registers:                PASS
    eth1 device registers:                PASS
    eth0 loopback All zeros:              PASS
    eth0 loopback All ones:               PASS
    eth0 loopback Walking ones:           PASS
    eth0 loopback Walking zeros:          PASS
    eth0 loopback Random pattern:         PASS
    eth1 loopback All zeros:              PASS
    eth1 loopback All ones:               PASS
    eth1 loopback Walking ones:           PASS
    eth1 loopback Walking zeros:          PASS
    eth1 loopback Random pattern:         PASS
--> Starting: [21] Verify PCI Configuration
--> Starting: [22] Mass Storage Initialization
--> Starting: [23] Mass Storage Drive Test
    AHCI: skipping register test
    AHCI: skipping controller test
    AHCI0 seek test:                      PASS
    AHCI0 read test:                      PASS
    AHCI: skipping DMA read test
    First sector is blank.
--> Starting: [24] BIOS Automatic Update
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
--> Starting: [25] Fibre HBA Automatic Update
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
AHCI0 MBR does not have a valid partition table
--> Starting: [26] Cluster Manager Reset
--> Starting: [27] Cluster Memory Initialization
Harrier ASIC found at 5.0.0.  CSR at 0xc0000000
Set0 DC DIMM 0.0.0 (J0300): Part #18HVF25672PZ-80EH1  SN:**confidential info erased**
Set0 DC DIMM 0.1.0 (J0301): Part #18HVF25672PZ-80EH1  SN:**confidential info erased** SPD Passed
Initializing Harrier at 5.0.0...
CSR=00:c0000000  SMW=00:a0000000  LMW=10:00000000  MMW=08:00000000
Running BIST Test: [GOOD]
CMA1: LPC1 is not Up, Trying LPC0
DMA PM using LPC2   CMA0 using LPC0  CMA1 using LPC0
RPC PM using LPC2   CMA0 using LPC0  CMA1 using LPC0
Set0 DC DIMM 0.0.0 (J0300): 2048 MB  CL4/6
Set0 DC DIMM 0.1.0 (J0301): 2048 MB  CL4/6
Present 1 Set 0, Side 0 Base = 00:00000000 Size = 00:ffffffff
Testing CMA interrupts: [............................]
Zero    32M cluster memory window: [                ]................]
Zero  4096M cluster memory window: [                               ]...............................]
Scan cluster memory for errors:    [                                ]................................]
CMA0 Cluster Memory is configured: 4096 MB CL4
Total Cluster Memory configured: 4096 MB
Harrier LPC Port Test: [............]
--> Starting: [28] Cluster Memory Diagnostic
test_list = 000136ff
    Testing CMA0 SMW data lines with walking 1
    Testing CMA0 SMW data lines with walking 0
    Testing CMA0 MMW data lines with walking 1
    Testing CMA0 MMW data lines with walking 0
    Testing CMA0 SMW ECC  lines with walking 1, channel 0
    Testing CMA0 SMW ECC  lines with walking 1, channel 1
    Testing CMA0 SMW ECC  lines with walking 0, channel 0
    Testing CMA0 SMW ECC  lines with walking 0, channel 1
    Testing CMA0 Opcode:  Zero ECC XOR PAR OR CRC
    Testing CMA0 SRC Interrupts CM->CM PM->CM CM->PM PM->PM 
    Testing CMA0 SMW address lines with walking 1
    Testing CMA0 SMW address lines with walking 0
    Testing CMA0 MMW address lines with walking 1 (first 4 GB only)
    Testing CMA0 MMW address lines with walking 0 (first 4 GB only)
    Testing CMA0 with random XOR (all Cluster Memory)
4095 MB [                                                  ]..................................................]
--> Starting: [29] Cluster PCI Diagnostic
--> Starting: [30] DIMM Information Collection
--> Skipping: [31] Manufacturing Centerpanel GPIO Test
--> Starting: [32] Serial Port Loopback Test
    Serial Port 0 [                ]................]      PASS
    Serial Port 1 [                ]................]      PASS
    Serial Port 2 [                ]................]      PASS
--> Skipping: [33] Manufacturing Serial Port Test
--> Starting: [34] Environmental Initialization
--> Starting: [35] Environmental Temperature and Voltage Test
           Expected   Reading  Lo Limit  Hi Limit  Status
        NODE 12.00V:  12.12 V   11.37 V   12.62 V  Within Tolerance
    NODE AUX 12.00V:  12.15 V   11.37 V   12.60 V  Within Tolerance
         HBA 12.00V:  12.12 V   11.35 V   12.64 V  Within Tolerance
         NODE 5.00V:   4.99 V    4.73 V    5.25 V  Within Tolerance
     NODE AUX 5.00V:   5.01 V    4.73 V    5.25 V  Within Tolerance
         NODE 3.30V:   3.30 V    3.12 V    3.47 V  Within Tolerance
          HBA 3.30V:   3.30 V    3.10 V    3.49 V  Within Tolerance
         FPGA 3.30V:   3.28 V    3.12 V    3.48 V  Within Tolerance
      PCIe SW 2.50V:   2.47 V    2.37 V    2.63 V  Within Tolerance
         PHY0 1.90V:   1.91 V    1.80 V    2.00 V  Within Tolerance
         PHY1 1.90V:   1.90 V    1.80 V    2.00 V  Within Tolerance
      CPU PLL 1.80V:   1.79 V    1.70 V    1.89 V  Within Tolerance
      PCIe SW 1.50V:   1.48 V    1.42 V    1.59 V  Within Tolerance
         NODE 1.20V:   1.19 V    1.13 V    1.26 V  Within Tolerance
          PCH 1.10V:   1.09 V    1.04 V    1.17 V  Within Tolerance
      CPU VTT 1.05V:   1.05 V    1.00 V    1.10 V  Within Tolerance
         NODE 1.00V:   0.99 V    0.89 V    1.05 V  Within Tolerance
     CPU VCCP 0.85V:   0.90 V    0.70 V    1.20 V  Within Tolerance
      CPU VSA 0.90V:   0.89 V    0.69 V    1.20 V  Within Tolerance
    DDR2 VDDQ 1.80V:   1.82 V    1.70 V    1.89 V  Within Tolerance
    DDR2 VTT  0.90V:   0.89 V    0.85 V    0.95 V  Within Tolerance
    DDR3 VDDQ 1.37V:   1.36 V    1.29 V    1.44 V  Within Tolerance
     DDR3 VTT 0.68V:   0.68 V    0.64 V    0.72 V  Within Tolerance
  Node Input 12.00V:  12.10 V   11.40 V   12.60 V  Within Tolerance
  Node InputCurrent:   5.58 A    0.00 A   16.61 A  Within Tolerance
   Node Input Power:  67.5  W   60.0  W  200.0  W  Within Tolerance
      LM87 Int Temp:     43 C       0 C      68 C  Within Tolerance
      LM87 Ext Temp:     39 C      -4 C      60 C  Within Tolerance
          LM92 Temp:     40 C       0 C      64 C  Within Tolerance
      LM94 Int Temp:     39 C       0 C      72 C  Within Tolerance
      LM94 Ext Temp:     38 C       0 C      67 C  Within Tolerance
   CPU Package Temp:     48 C       0 C     101 C  Within Tolerance
         DIMM0 Temp:     41 C       0 C      80 C  Within Tolerance
--> Starting: [36] Test CPU Operation
--> Skipping: [37] Manufacturing Cluster Link Initialization
--> Skipping: [38] Manufacturing Cluster Link Test
--> Starting: [39] PCI Fibre Channel/SAS Adapter Test
SAS HBA LSI    0087 at  6.0.0 (PCI slot 0)  [Ver: 11.00]
   Register test          [  ]..]                PASS
   PCI walking bits       [        ]........]          PASS
   PCI pattern test       [   ]...]               PASS
   CM0.2 walking bits     [        ]........]          PASS
   CM0.2 pattern test     [   ]...]               PASS
FC HBA Emulex f100 at  7.0.0 (PCI slot 1)   [U3D2.01X14]
   Register test          [        ]........]          PASS
   Memory test            [  ]..]                PASS
   PCI walking bits       [   ]...]               PASS
   PCI pattern test       [   ]...]               PASS
   CM0.2 walking bits     [   ]...]               PASS
   CM0.2 pattern test     [   ]...]               PASS
FC HBA Emulex f100 at  7.0.1 (PCI slot 1)   [U3D2.01X14]
   Register test          [        ]........]          PASS
   Memory test            [  ]..]                PASS
   PCI walking bits       [   ]...]               PASS
   PCI pattern test       [   ]...]               PASS
   CM0.2 walking bits     [   ]...]               PASS
   CM0.2 pattern test     [   ]...]               PASS
--> Starting: [40] PCI iSCSI Adapter Test
--> Starting: [41] System Error Reporting Init
--> Skipping: [43] Manufacturing CP EEPROM Test
--> Starting: [44] Certify OS Startup
--> Skipping: [45] Table Execution Summary
+-----------------------------------------------------------------------------+
HP SPI Image 1.2.9.  Release version. 10:55:06 Nov 16 2012.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Pair0 DIMM0  (J0155): 8192 MB  CL5/10
|  Data Cache Size         4 GB  CL4/6
|                          Set0 DC DIMM 0.0.0 (J0300): 2048 MB  CL4/6
|                          Set0 DC DIMM 0.1.0 (J0301): 2048 MB  CL4/6
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk SSD U100 64GB     123612401529        64 GB
|  PCI Slot 0              LSI-SAS 9205-8e    
|  PCI Slot 1              Emulex  LPe12002          VM80175440          2-port
|  Board 920-200040.A5     FXN 2013/02/Wed 00139547  84:34:97:66:04:04
|  Cluster serial          1613873                   84:34:97:66:04:05
|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 01:58:18 (UTC-4)
+-----------------------------------------------------------------------------+
Booting from device 0, AHCI0Invalid boot sector.
Use "boot net install" to correct this.

*** Fatal error: Code 39, sub-code 0x10 (0).
AHCI0 MBR does not have a valid partition table
Disabled FSBC boot watchdog.

*** Fatal error: Code 39, sub-code 0x10 (0).

*** Fatal error: Code 39, sub-code 0x10 (0).
Disabled FSBC boot watchdog.

Whack>
Whack>banner
+-----------------------------------------------------------------------------+
HP SPI Image 1.2.9.  Release version. 10:55:06 Nov 16 2012.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Pair0 DIMM0  (J0155): 8192 MB  CL5/10
|  Data Cache Size         4 GB  CL4/6
|                          Set0 DC DIMM 0.0.0 (J0300): 2048 MB  CL4/6
|                          Set0 DC DIMM 0.1.0 (J0301): 2048 MB  CL4/6
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk SSD U100 64GB     123612401529        64 GB
|  PCI Slot 0              LSI-SAS 9205-8e           No SN               
|  PCI Slot 1              Emulex  LPe12002          VM80175440          2-port
|  Board 920-200040.A5     FXN 2013/02/Wed 00139547  84:34:97:66:04:04
|  Cluster serial          1613873                   84:34:97:66:04:05
|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 01:58:36 (UTC-4)
+-----------------------------------------------------------------------------+
Whack>
Whack>
Whack>
Whack>Loading PEIM at 0x000FFFD85A0 CpuPeim.efi
Loading PEIM at 0x000FFFCBD20 PcatSingleSegmentPciCfg2Pei.efi
Loading PEIM at 0x000FFFCD620 PciCfgOnPciCfg2Thunk.efi
Loading PEIM at 0x000FFFD5CA0 PlatformInfo.efi
Board ID = BoardIdEOSNode 
   Verifying NEMOE startup...
   Waited 2700 ms for NEMOE boot
EOS SAS Buffers Initialization Completed.
BIOS Version: HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.

<part omitted>

Bootstrap CPU0
      Intel(R) Xeon(R) CPU E5-2428L 0 @ 1.80GHz
      Family 6, Model 45, Stepping 7, Features bfebfbff:3
      SKU Info: Max Frequency Ratio 18, Max Core Count 6
      CPU speed: 1800.00 MHz
      Bus speed:  100.00 MHz
      Bus to CPU ratio: 1/18

Board reset reason: PCI_RESET
Previous reason   : PCI_RESET

Disabled FSBC boot watchdog.

Warning: PCI scan has not completed.  It is not safe to use most Whack
commands at this point.  Please resume initialization by typing "go" now.
Whack>banner
+-----------------------------------------------------------------------------+
HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Set0 CC DIMM0.0 (J0155): 8192 MB  CL5/10
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA Disk               Not present
|  PCI Slot 0              FAILED
|  PCI Slot 1              FAILED
|  Board 920-200040.A6     FXN 2019/03/Sun 00016530  |  Cluster serial          1613873Ethernet device requires completion of the PCI bus scan.

|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 15:11:19 (UTC+9)
+-----------------------------------------------------------------------------+
Whack>ide eras        prom edit
Board Spin:       04
Size * 256 bytes: 04
Board Class:      920
Board Base:       200040
Board Rev:        A6
Assembly Vendor:  FXN
Assembly Year:    2019
Assembly Week:    03
Assembly Day:     01
Assembly Serial:  00016530
System Serial:    1613873
Node ID:          00
Midplane Type:    1a
Node Type:        20
W19:              0fffffff
Whack>
Whack>
Whack>prom hp
HW Revision:         004 
Product ID:          HP_3PAR 7200            
Assembly Serial Num: **removed**
Assembly Part Num:   QR482-63001     
Saleable Serial Num: **removed**
Saleable Part Num:   QR482A          
Spare Part Num:      683245-001      
Whack>ahci init
Disk 0: AHCI0:
       Model: SanDisk DX110064A5xnNMRI  Serial: **removed** Rev: X231600
    Capacity: 64.023 GB (125045424 blks)  SSD
         WWN: 5001b44ca6c2
   Interface: ATA-8     PIO mode: 0   Queue depth: 31   ECC bytes 0
        Write cache     ON
        SMART           ON
        Power saving    OFF
Whack>ide erase
ide commands unsupported on this platform
passing command to ahci...
Warning!! Security erase can take over an hour
Erase all AHCI0 drive data -- Are you sure? (Y/N) Yes
Security Status Bits = 0x21
Security Set Password passed
Security Erase Prepare passed
Enhanced Security Erase supported
Performing Enhanced Security Erase
Erasing
........
Security Erase Unit passed
Security Status Bits = 0x21
Whack>banner
+-----------------------------------------------------------------------------+
HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Set0 CC DIMM0.0 (J0155): 8192 MB  CL5/10
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk DX110064A5xnNMRI  144337400642        64 GB
|  PCI Slot 0              FAILED
|  PCI Slot 1              FAILED
|  Board 920-200040.A6     FXN 2019/03/Sun 00016530  |  Cluster serial          1613873Ethernet device requires completion of the PCI bus scan.

|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 15:20:27 (UTC+9)
+-----------------------------------------------------------------------------+
Whack>
Whack>
Whack>reset
Resetting...
Trapped IO 0xcf9 write of 0xa
Rebooting due to IO 0xcf9 write of 0xe
Loading PEIM at 0x000FFFD85A0 CpuPeim.efi
Loading PEIM at 0x000FFFCBD20 PcatSingleSegmentPciCfg2Pei.efi
Loading PEIM at 0x000FFFCD620 PciCfgOnPciCfg2Thunk.efi
Loading PEIM at 0x000FFFD5CA0 PlatformInfo.efi
Board ID = BoardIdEOSNode 
   Verifying NEMOE startup...
EOS SAS Buffers Initialization Completed.
BIOS Version: HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.

<part omitted>

Refresh Rate 7.800us tREF = 2080 (0x0820)
Refresh Rate 7.800us tREF = 2080 (0x0820)
Testing CMA interrupts: [............................]
Zero    32M cluster memory window: [                ]................]
Zero  4096M cluster memory window: [                               ]...............................]
Scan cluster memory for errors:    [                                ]................................]
CMA0 Cluster Memory is configured: 4096 MB CL4
Total Cluster Memory configured: 4096 MB
Harrier LPC Port Test: [............]
--> Starting: [28] Cluster Memory Diagnostic
    test_list = 000136ff
    Testing CMA0 SMW data lines with walking 1
    Testing CMA0 SMW data lines with walking 0
    Testing CMA0 MMW data lines with walking 1
    Testing CMA0 MMW data lines with walking 0
Disabled FSBC boot watchdog.

Whack>
Whack>set perm cnt_no_os_boot=0
Whack>set perm cnt_no_cluster=0
Whack>set perm cnt_no_shutdown=0
Whack>set perm cnt_os_panic=0
Whack>set perm cnt_same_fatal=0
Whack>set perm cnt_log_error=0
Whack>set perm sys_serial=1613873
Whack>eth dev 0
Selected ethernet device 0 at Memory c0600000
Whack>net addr 169.254.172.229
My address is 169.254.172.229
Whack>net netmask 0.0.0.16
Network mask 0.0.0.16
Whack>net gateway 192.168.40.72
Gateway address 192.168.40.72
Whack>net server 192.168.40.72
Server address 192.168.40.72
Whack>boot net install cr=3 ipaddr=169.254.172.229 nm=255.255.0.0 rp=192.168.40.72::rescue hn=1613873_0 eth=eth0
    Testing CMA0 SMW ECC  lines with walking 1, channel 0
    Testing CMA0 SMW ECC  lines with walking 1, channel 1
    Testing CMA0 SMW ECC  lines with walking 0, channel 0
    Testing CMA0 SMW ECC  lines with walking 0, channel 1
    Testing CMA0 XCB Opcode:  Zero ECC XOR PAR OR CRC
    Testing CMA0 SRC Interrupts CM->CM PM->CM CM->PM PM->PM 
    Testing CMA0 SMW address lines with walking 1
    Testing CMA0 SMW address lines with walking 0
    Testing CMA0 MMW address lines with walking 1 (first 4 GB only)
    Testing CMA0 MMW address lines with walking 0 (first 4 GB only)
    Testing CMA0 with random XOR (all Cluster Memory)
4095 MB [                                                  ]..................................................
--> Skipping: [29] Cluster PCI Diagnostic
--> Starting: [30] DIMM Information Collection
Collecting CPU DIMM info:
Collecting ASIC DIMM info:
--> Skipping: [31] Manufacturing Centerpanel GPIO Test
--> Skipping: [32] Serial Port Loopback Test
--> Skipping: [33] Manufacturing Serial Port Test
--> Starting: [34] Environmental Initialization
--> Skipping: [35] Environmental Temperature and Voltage Test
--> Skipping: [36] Test CPU Operation
--> Skipping: [37] Manufacturing Cluster Link Initialization
--> Skipping: [38] Manufacturing Cluster Link Test
--> Skipping: [39] PCI Fibre Channel/SAS Adapter Test
--> Skipping: [40] PCI iSCSI Adapter Test
--> Starting: [41] System Error Reporting Init
--> Skipping: [43] Manufacturing CP EEPROM Test
--> Skipping: [44] Certify OS Startup
--> Skipping: [45] Table Execution Summary
+-----------------------------------------------------------------------------+
HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Set0 CC DIMM0.0 (J0155): 8192 MB  CL5/10
|  Data Cache Size         4 GB  CL4/6
|                          Set0 DC DIMM0.0 (J0300): 2048 MB  CL4/6
|                          Set0 DC DIMM1.0 (J0301): 2048 MB  CL4/6
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk DX110064A5xnNMRI  144337400642        64 GB
|  PCI Slot 0              LSI-SAS 9205-8e    
|  PCI Slot 1              Emulex  LPe12002          VM80175440          2-port
|  Board 920-200040.A6     FXN 2019/03/Sun 00016530  b4:b5:2f:a7:5c:b8
|  Cluster serial          1613873                   b4:b5:2f:a7:5c:b9
|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 15:22:13 (UTC+9)
+-----------------------------------------------------------------------------+
AHCI0 MBR does not have a valid partition table
BIOS wrote initial PCIe tree to idelog
Booting from net...
    TFTP "install" from 192.168.40.72.............................................................................................................................................................................................................................................................................................complete

Setting FSB WDT Boot Complete State.
WARNING: Ancient bootloader, some functionality may be limited!
[    0.000000] reserve_trampoline_memory ffff880000006000

<part omitted>

--> Starting: [40] PCI iSCSI Adapter Test
--> Starting: [41] System Error Reporting Init
--> Skipping: [43] Manufacturing CP EEPROM Test
--> Starting: [44] Certify OS Startup
--> Skipping: [45] Table Execution Summary
+-----------------------------------------------------------------------------+
HP SPI Image 4.8.38.  Release version. 16:57:04 Jul 17 2015.
+-----------------------------------------------------------------------------+
|  CPU                     1 x 1.80 GHz Sandy Bridge quad core HT dual
|  Control Cache Size      7.100 GB  (cpu mem type 11) CL9
|                          Set0 CC DIMM0.0 (J0155): 8192 MB  CL5/10
|  Data Cache Size         4 GB  CL4/6
|                          Set0 DC DIMM0.0 (J0300): 2048 MB  CL4/6
|                          Set0 DC DIMM1.0 (J0301): 2048 MB  CL4/6
|  Slot ID                 0  [2 Node HP 3PAR 7200 Centerplane]
|  FPGA                    Eos v0.e
|  SATA0 Disk              SanDisk DX110064A5xnNMRI  144337400642        64 GB
|  PCI Slot 0              LSI-SAS 9205-8e    
|  PCI Slot 1              Emulex  LPe12002          VM80175440          2-port
|  Board 920-200040.A6     FXN 2019/03/Sun 00016530  b4:b5:2f:a7:5c:b8
|  Cluster serial          1613873                   b4:b5:2f:a7:5c:b9
|  Board reset reason      PCI_RESET
|  Current Time            2024-08-20 15:26:56 (UTC+9)
+-----------------------------------------------------------------------------+
BIOS wrote initial PCIe tree to idelog
Booting from device 0, AHCI0
Setting FSB WDT Boot Complete State.
GRUB loading.
W. 
 elcome to GRUB!

P 
 ress ESC to display the GRUB menu... 10    9    8    7    6    5    4    3    2    1    0                                                                                                                                                      
  Booting '3.2.2.612'

<Part omitted>

init: coreman: file system usage - /dev/sda7 - used=9304148KB (used-core=560KB) free=17983624KB total=27287772KB
init: coreman: space removal targets - freeMin=0KB freePct=0KB  corePct=0KB targetToRemove=0KB targetToRemoveMinLow=0KB
init: coreman: exit - no free space requirements to satisfy
init: Launching tpd_cfg_tornado_dcncage script to work around 'Configures a Tornado Enclosures DP-1 port' issue
init: Running local boot script
3PAR(R) InForm(tm) OS 3.2.2.612 1613873-0 ttyS0
1613873-0 login: 

[Moderator edit: Erased the confidential info.]

[Mr_Techie]

Hi @555-denoh 

Replying you for a old thread, 

The errors you're encountering with the 3PAR7200 during the node rescue process suggest compatibility issues between the SPI (Service Pack Image) and the 3PAR OS version

Some key points to note is: 

-Each SPI image is designed to work with specific versions of the 3PAR OS. An SPI image that is too old (like 1.2.9) may not support newer features or the underlying OS structure of a more recent 3PAR OS (like 3.2.2MU4).

- In your case, the SPI Image 1.2.9 is not compatible with the 3PAR OS 3.2.2MU4, which is why you are seeing boot errors when using it with that version.

- Since the SPI Image 4.8.38 completed the node rescue successfully, it confirms that it is compatible with the 3PAR OS version you are using. This image likely contains the necessary updates and configurations required for proper functionality.

- You might need to check the HPE 3PAR Storage System Compatibility Guide or Release Notes for specific information regarding supported versions.

I hope this helps, Let me know

[555-denoh · Accepted solution]

Hello .
This is Hajime Shimaya
Thank you for your advice.　
We have solved this problem.

<>Purpose>
We need to execute 3PAR OS on a New 2 nodes for The inspection

<Action plan>
I installed the 3PAR OS 3.2.2 (eMU4) SSD of equipment 7200 in a new node(SPI 1.2.9).
I boot up it with that combination. After booting it, I will try to upgrade the SPI with the upgradecage command.

<Progress>
1. Insert the 3PAR OS 3.2.2 (eMU4) SSD of equipment 7200 into the two new nodes(SPI 1.2.9) .
2. Booted normally, and I found the update from SPI 1.2.9 to SPI 4.8.38 when the OS Booting up.
This is a behavior I hadn't noticed before.
===========Console Message================
Currently in the main SPI flash memory: [5632 KB]
HP SPI Image 1.2.9. Release version. 10:55:06 Nov 16 2012.
SPI image loaded: [8192 KB]
HP SPI Image 4.8.38. Release version. 16:57:04 Jul 17 2015.
will be written to the main flash memory.
Flash Update Task Listing:
#: Dst Src Length Flags
-- ---------- ---------- ---------- -------------------------
0: 0x00000000 0x00000000 0x00010000 (0x00)
1: 0x00280000 0x00280000 0x00580000 (0x88) BIOS Reboot
Erasing SPI at: 0x00000000; Length: 0x00010000
Verifying Erase at: 0x00000000; Length: 0x00010000
Writing SPI at: 0x00000000; Length: 0x00010000
Verifying SPI at: 0x00000000; Length: 0x00010000
Erasing SPI at: 0x00280000; Length: 0x00580000
Erasing blocks: [ ]...........]
Verifying Erase at: 0x00280000; Length: 0x00580000
Verifying erase: [ ]...........]
Writing SPI at: 0x00280000; Length: 0x00580000
Writing bytes: [ ]...........]
Verifying SPI at: 0x00280000; Length: 0x00580000
Verifying bytes: [ ]...........]
Flash updates complete. You may now reboot
===========Console Message================

3. New Nodes boot up Login prompt, but I can't login in with 3paradm/3pardata.
4. When I access from SP 7, 1
===========Console Message================
Could not open connection to CLI server process on "192.168.40.72":

Socket connection timed out to port 2550 on 192.168.40.72
System name or port may be invalid, or the process may not have started yet or may have failed.
===========Console Message================
but I can't login
The node port changed, so that's where the error occurred. Probably because the MAC address changed.

5.I couldn't shutdown command, so I pulled out the node and stopped 3PAR Node.
6.Returned the SSD to the original.
7. Started equipment 7200 with the original configuration.
8. Performed node rescue on two new nodes with SPI 4.8.38.
Both were successful. The inspection is now complete.

Thanks Regard.

[Sunitha_Mod]

Hello Hajime, 

That's Excellent! 

We are extremely glad to know the issue has been resolved. 

[Mr_Techie]

@555-denoh 

I'm glad it was solved.