HPE SimpliVity
1748136 Members
3560 Online
108758 Solutions
New Discussion юеВ

Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

 
SOLVED
Go to solution
RicT1
Valued Contributor

Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

Hi,

I tried to deploy a single Simplivity DL380 Gen 10 XS node in version 3.7.6 and each time i have the following error: step 31 of 32 -Cannot connect to Virtual Controller after rebooting it.

After the installation error, i can connect normally to the ESXi (10.0.0.116) and the OVC (10.0.0.117).

I found this error on orchestrator log file:

2019-01-30 14:45:29,985Z INFO  OmniStack-10.0.0.116 [c.s.d.o.Orchestrator] connect(SvtControlConnect.java:82) - Connection to OmniCube at 10.0.0.117 port 9190 failed - exception java.net.ConnectException: Connection refused: connect
java.net.ConnectException: Connection refused: connect
    at java.net.DualStackPlainSocketImpl.waitForConnect(Native Method)
    at java.net.DualStackPlainSocketImpl.socketConnect(Unknown Source)
    at java.net.AbstractPlainSocketImpl.doConnect(Unknown Source)
    at java.net.AbstractPlainSocketImpl.connectToAddress(Unknown Source)
    at java.net.AbstractPlainSocketImpl.connect(Unknown Source)
    at java.net.PlainSocketImpl.connect(Unknown Source)
    at java.net.SocksSocketImpl.connect(Unknown Source)
    at java.net.Socket.connect(Unknown Source)
    at sun.security.ssl.SSLSocketImpl.connect(Unknown Source)
    at com.simplivity.util.network.AutoCert.initSSLSocket(AutoCert.java:224)
    at com.simplivity.util.network.AutoCert.getSvtTrustStore(AutoCert.java:191)
    at com.simplivity.util.network.AutoCert.verifyCert(AutoCert.java:110)
    at com.simplivity.util.network.AutoCertThrift.getTransport(AutoCertThrift.java:51)
    at com.simplivity.deploy.orchestrator.SvtControlConnect.connect(SvtControlConnect.java:73)
    at com.simplivity.deploy.orchestrator.DeployActions.connectSVT(DeployActions.java:3319)
    at com.simplivity.deploy.orchestrator.CustomerDeploy.runSteps(CustomerDeploy.java:163)
    at com.simplivity.deploy.orchestrator.DeployExecutor.run(DeployExecutor.java:439)
    at java.lang.Thread.run(Unknown Source)
2019-01-30 14:45:29,986Z ERROR OmniStack-10.0.0.116 [c.s.d.o.Orchestrator] error(DeployLogger.java:98) - step 31 of 32 (49.78%) - Cannot connect to Virtual Controller after rebooting it - at 10.0.0.117

Thanks for help on this problem

Regards

 

 

 

4 REPLIES 4
DeclanOR
Respected Contributor

Re: Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

Hi @RicT1

Thanks for your query.

You will probably need to raise a support ticket to look into this with you, however, can you maybe try one thing?

Can you power down the node for 5 mins, and then re-attempt the deployment? If this doesn't help, then please raise a ticket.

Thanks,

Declan.

Accept or Kudo



RicT1
Valued Contributor
Solution

Re: Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

Hi,

The issue was cause by a faulty GPU card. The CPU card was blinking red at the rear of the server. HPe support will replace the GPU card.

Also, i could connect the OVC after the failed deployement and i found the following error with dmesg command.

[ 56.498229] IA0: C2S Console: [ 6169.240000] xi2cps e0005000.ps7-i2c: I2C_ERROR err_status 0x4 isr 0x4 CR 0x320e SR 0x40 recv_count 0 send_count 0
[ 56.508455] IA0: C2S Console: [ 6169.250000] envmon ERROR: get_i2c_register:418 Unable to send I2c data: Input/output error
[ 56.517019] IA0: C2S Console: [ 6169.260000] envmon ERROR: get_STTS2002_temp:444 Unable to get I2C register! bus /dev/i2c-1, addr 0x18 reg 0x0: Input/output error
[ 56.529014] IA0: C2S Console: [ 6169.270000] xi2cps e0005000.ps7-i2c: I2C_ERROR err_status 0x4 isr 0x4 CR 0x320e SR 0x40 recv_count 0 send_count 0
[ 56.539241] IA0: C2S Console: [ 6169.280000] envmon ERROR: get_i2c_register:418 Unable to send I2c data: Input/output error
[ 56.547745] IA0: C2S Console: [ 6169.290000] envmon ERROR: get_STTS2002_temp:444 Unable to get I2C register! bus /dev/i2c-1, addr 0x18 reg 0x0: Input/output error

Thanks,

Ric

 

DeclanOR
Respected Contributor

Re: Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

@RicT1 

Thanks for confirming. I suspect you mean the TIA (accelerator) card correct?

This is what I suspected. A drain of the flea power as suggested often resolves issues with the TIA card which is why I recommended the power down for 5 minutes. If the TIA was actually faulty, then this would not have helped either.

Glad to hear you got this resolved with help of support.

Best ragrds,

DeclanOR

Accept or Kudo



RicT1
Valued Contributor

Re: Deployement failed step 31 of 32 :Cannot connect to Virtual Controller after reboot

Hello,

Yes i confirm, it's mean the TIA (accelerator) card.

Best Regards

Ric