Problems with ram after upgrading the cpu

[Zen0xus]

Hey! I have a problem with my HP Proliant DL380 G6.

After upgrading my CPU (E5530 to X5670) i've had problems with the dimm slots.

I've installed on every dimm slot 4gb "Rx4 PC3 10600R RAM.
But the dimmslots 1-4-7 wont work after upgrading the cpu...

I tired everything, Changing the RAM etc and I don't know what to do...

Maybe you guys can help me

Kind Regards
 -Zen0xus

[SanjeevGoyal]

Hello,

Please follow the  HP ProLiant DL380 G6 QuickSpecs (Page No 3)

https://h20195.www2.hpe.com/v2/getdocument.aspx?docname=c04282582

Memory Type DDR3 Registered (RDIMM) and Unbuffered (UDIMM)
Standard (Performance
Models)
12GB (6 x 2GB) PC3-10600R (DDR3-1333) Registered DIMMs
Standard (Base Models) 6GB (3 x 2GB) PC3-10600R (DDR3-1333) Registered DIMMs
Standard (Entry Models) 4GB (2 x 2GB) PC3-10600R (DDR3-1333) Registered DIMMs
Standard (High Efficiency
Models)
4GB (2 x 2GB) PC3-10600E (DDR3-1333) Unbuffered DIMMs
Maximum (RDIMM) 192GB (12 x 16GB) for Registered Memory configurations
Maximum (UDIMM) 48GB (12 x 4GB) for Unbuffered Memory configurations
NOTE: If only one processor is installed, only half the DIMM slots are available
NOTE: when populating with the 16GB Memory Kits (Quad-Rank), only 12 DIMMs can be populated.
NOTE: For G6 and G7 servers using Xeon 5600 series processors, the default memory speed is
1333MHz with either one or two DIMMs per channel. For G6 and G7 servers using Xeon 5500 series
processors, an RBSU option is available to disable 1333MHz operation (which will result in 1067MHz
operation).
NOTE: UDIMM support is only on 12-slot servers.
NOTE: Depending on the memory configuration and processor model, the memory speed may run at
1333MHz, 1066MHz, or 800MHz. Please see the Online Memory Configuration Tool at:

HPE ProLiant DL360 G6 Server - Configuring Memory

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c01761995

If you feel this was helpful please click the KUDOS! thumb below!   

Regards,

[Zen0xus]

I've already seen this HPE entrys, but that hasnt helped me.

like i said, i tryed everything... (Changing the positions of the ram etc...)

But i am getting exact the same error. (Since i changed the CPU E5530 to X5670 One socket)).. Dimmsolot 1-4-7 wont work... or rather when i install RAM, the ilo is showing me:

PROC 1 DIMM 1G : not installed PROC 1 DIMM 2D : 4096 MB 1333 MHz PROC 1 DIMM 3A : 4096 MB 1333 MHz PROC 1 DIMM 4H : not installed PROC 1 DIMM 5E : 4096 MB 1333 MHz PROC 1 DIMM 6B : 4096 MB 1333 MHz PROC 1 DIMM 7I : not installed PROC 1 DIMM 8F : 8192 MB 1333 MHz PROC 1 DIMM 9C : 4096 MB 1333 MHz

[SanjeevGoyal]

Hello, 

I would suggest you contact to HPE  for deep drive analysis if you have already followed the suggested recommendations.

Regards,